• 대한기계학회논문집
• /
• 제11권1호
• /
• pp.145-153
• /
• 1987

본 논문에서는 예혼합동축분류화염에 있어서 재순환역 안으로의 기체(공기, 연료, 혼합기) 주입과 2차공기의 족회가 화염안정성, 화염형상 및 재순환역에 미치는 영향을 명확히 하였다.

• 한국분무공학회지
• /
• 제16권1호
• /
• pp.7-14
• /
• 2011

High pressure LPG fuel spray with a conventional swirl injector was visualized and the impact of the injection pressure was also investigated using a DISI (direct injection spark ignition) LPG single cylinder engine. Engine performance and emission characteristics were evaluated over three different injection pressure and engine loads at an engine speed of 1500 rpm. The fuel spray pattern appeared to notably have longer penetration length and narrower spray angle than those of gasoline due to its lower angular momentum and rapid vaporization. Fuel injection pressure did not affect combustion behaviors but for high injection pressure and low load condition ($P_{inj}$=120 bar and 2 bar IMEP), which was expected weak flow field configuration and low pressure inside the cylinder. In terms of nano particle formation the positions of peak values in particle size distributions were not also changed regardless of the injection pressure, and its number densities were dramatically reduced compared to those of gasoline.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.35-41
• /
• 2014

The wood pellet, which is one of the woody biomass energy, has very high economic efficiency and combustion efficiency during their combustion. The existing pellet burner have many problems such as low combustion efficiency, flame stabilization, ash problem and ignition time etc. We developed cyclonic wood pellet burner aim to 20,000kcal/hr boiler and measured temperature profiles and exhaust gases in order to investigate the flame stability and optimum combustion condition at any air flow conditions. As results, we confirmed the reappearance and the isotropy of the experimental results in the burner. At the first air flow inlet condition of excess air ratio ${\alpha}=0.02$, second air flow $490{\ell}/min$ had the best combustion condition when pellet supplied 30g. This result means that we need much air supply only for the swirling of second air flow. So we tested various second air flux at first air excess air ratio ${\alpha}=0.7$ condition. At this condition, we could find out that we don't need much second air and total air flux compared to the former condition. We will continuously test this work of air flow distribution, and swirl effect of first air flow, and ash elimination.

• 한국수소및신에너지학회논문집
• /
• 제18권1호
• /
• pp.75-84
• /
• 2007

The effects of hydrogen enrichment to methane on NOx formation have been investigated with swirl stabilized pre-mixed hydrogen enriched methane flame in a laboratory-scale pre-mixed combustor(nominally of 5,000 kcal/hr). The hydrogen enriched methane fuel and air were mixed in a pre-mixer and introduced to the combustor through different degrees of swirl vanes. The flame stability was examined for different amount of hydrogen addition to the methane fuel, different combustion air flow rates and swirl strengths by comparing equivalence ratio at the lean flame limit. The hydrogen addition effects and swirl intensity on the combustion characteristics of pre-mixed methane flames were examined using gas analyzers, and OH chemiluminescence techniques to provide information about species concentration of emission gases and flowfield. The results of NOx and CO emissions were compared with a diffusion flame type combustor. The results show that the lean stability limit depends on the amount of hydrogen addition and the swirl intensity. The lean stability limit is extended by hydrogen addition, and is reduced for higher swirl intensity at lower equivalence ratio. The addition of hydrogen increases the NOx emission, however, this effect can be reduced by increasing either the excess air or swirl intensity. The NOx emission of hydrogen enriched methane premixed flame was lower than the corresponding diffusion flame under the fuel lean condition.

• 한국항공우주학회지
• /
• 제48권1호
• /
• pp.35-42
• /
• 2020

비행체용 전기식 구동장치는 일반적으로 공력비행 조종날개의 편향각 또는 추력방향을 제어하는 장치로 본 논문은 공력제어와 추력방향 제어가 모두 가능한 전기식 구동장치의 설계 및 개발을 다루고 있다. 본 논문에서는 하나의 작동기로 미익과 제트 베인을 동시에 제어할 수 있고, 비행체의 표적까지 비행동안 효율을 증가시키기 위하여 수직 발사 및 고속 선회 후 제트 베인을 분리할 수 있는 새로운 소형 전기식 구동장치를 제안하였다. 이를 위하여, 푸시-푸시 링크 구조를 사용한 전기식 구동장치를 설계하였고 수학적 모델을 유도하였다. 수학적 모델은 시뮬레이션 결과와 실험 결과를 비교하여 모델의 타당성을 검증하였다. 개발된 구동장치의 성능 및 신뢰성은 성능시험, 환경시험, 지상연소시험을 통하여 검증하였다. 제안된 구동장치는 성능 및 신뢰성 뿐만 아니라 단순하고 콤팩트한 구조로 인해 비행체용 전기식 구동장치로 유용할 것으로 기대된다.