• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.57-62
• /
• 2013

Because there is no suspension and differential devices at cart body, the deformation of the frame happened during kart driving affects the driving performance caused by the elastic deformation and the fatigue life of kart frame resulted from the permanent deformation. The dynamic behavior of kart caused by the torsional deformation during circular driving is the important factor of these two kinds of deformations. In order to analyze the dynamic behavior of kart at this curved section, GPS is used to trace the track of kart and the torsional stress at kart-frame has been measured with real time. The mechanical properties of kart-frames for leisure and racing are investigated through material property analysis and tensile test. Torsional stress concentration and frame distortion are investigated through stress analysis on frame on the basis of study result. The real karts for leisure and racing kart are also tested in each driving condition by using the driving analysis equipment. The driving behavior of kart at the curved section are investigated through this test. As the phenomenon of load movement due to centrifugal force at car is happened during circular driving, the torsional stress occurs at cart steel frame.

• Journal of Advanced Navigation Technology
• /
• v.26 no.6
• /
• pp.448-455
• /
• 2022

In this study, when establishing a UTM(UAS Traffic Management) system, a corridor must be set to separate the flight distance between unmanned aerial vehicles, and the size of the corridor was calculated in consideration of TSE(Total System Error). The flight data of the straight section and the turning section were collected using a hybrid vertical take-off and landing unmanned aerial vehicle. The flight data were derived from the TSE using the SQSM(Scalar Quantity Summation Method) method, and the impact on the straight and turning sections was analyzed by calculating in detail by NSE(Navigation System Error) and FTE(Flight Technical Error). The corridor size was calculated by referring to the TSE analysis results and PBN (Performance-based Navigation) manual.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.87-92
• /
• 2010

This study evaluates the laboratory properties of asphalt binder and mixture modified with R-EPDM(Recycling Ethylene Propylene Dien Monometer), which consists of R-EPDM as a main ingredient that is an industrial by-product made by manufacturing waste EPDM below 50 mesh as an additive. Superpave system was used to determine the PG(Performane Grade) and evaluate the property of R-EPDM modified binder. OACs(Optimum Asphalt Contents) of R-EPDM modified asphalt mixtures were determined by Superpave mix design using gyratory compactor and wheel tracking test and moisture susceptibility test were carried out with R-EPDM modified asphalt mixtures at OACs. The results from these tests, rutting-resistance and freezing and thawing resistance by moisture susceptibility of R-EPDM modified asphalt mixtures were superior to one of general asphalt mixtures(AP-5).

• The KSFM Journal of Fluid Machinery
• /
• v.5 no.3 s.16
• /
• pp.46-53
• /
• 2002

This paper reports an experimental investigation on a centrifugal compressor with the adjustable inlet guide vane. The compression system is composed of a radial impeller, a vaneless diffuser, and an IGV. The results have shown that surge line on the performance map is affected by the amount of prewhirl and the prewhirl has an effect on transient region between rotating stall and surge. The surge lines have been shifted toward the lower flow region with the increased positive prewhirl and the higher flow region with the increased negative prewhirl. During the unsteady performance test, it was also found that the transient region was reduced with the increased negative prewhirl, and weak signals of rotating stall were detected just before surge as the positive prewhirl was increased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.375-378
• /
• 2011

A valve's high response for controlling thruster is essential for rapid turning during initial short moment after launching. The actuator for controlling the valve is simultaneously used in controlling canard of a guided missile. This paper explain development process for the electromechanical actuator interlocked with canard by arranging in following order, design, analysis, manufacture, test and evaluation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.309-309
• /
• 2014

음극방식법은 피방식체에 외부전원을 인가하거나 보다 활성인 금속을 전기적으로 연결하여 피방식체의 전위가 일정 전위까지 음극분극 되도록 하여 부식을 억제하는 방법이다. 이러한 음극 방식의 결과로 $OH^-$이온이 금속 표면 부근에 생성되고 금속/해수 사이의 pH 증가를 유발하게 되며, 높은 pH는 $Mg(OH)_2$ 및 $CaCO_3$의 석출을 유발한다. 전착 박막은 각각 1, 3, 6, 12시간 및 5, 15, $20mA/cm^2$의 전류 밀도 조건에서 자연 해수, $CO_2$ 가스가 용해된 해수 용액 내에서 스틸 기판 상에 전기적 증착기술을 가해 형성되었다. 상기 조건에서 증착 된 박막의 내용물은 주사 전자 현미경 (SEM) 및 X-선회절(XRD)에 의해 조사되었다. 또한 코팅 박막의 내식성은 전기화학적 양극 분극시험에 의해 평가되었다.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.6
• /
• pp.776-781
• /
• 2010

In the ship-handling simulator, it is important for a ship manoeuvring model to represent the dynamic characteristic of a ship and to be simple for reducing calculation time. Especially, even if principal dimensions of a ship are given in initial design stage, or manoeuvring test data are only given by model or real ship's trials, simulations are often needed to check the manoeuvrability of a ship. In this paper, a simple manoeuvring model based on turning test data of a ship is mathematically developed. And the simulation results are verified by comparing with turning test results of a real ship.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.4-4
• /
• 1999

최근 충남대에서는 다양한 추진제와 연소 조건으로 액체로켓 연소 실험이 진행되고 있으며 그에 비례하여 많은 사고들이 발생하고 있다. 한 예로 GO$_2$/kerosene을 추진제로 하는 노즐삭마 시험용 로켓엔진(추력 1001bf, 연소실 압력 600psia) 개발 중에 화염이 인젝터면에 형성되어 인젝터면을 손상시키는 사고를 여러 번 경험하게 되었다. 본 연구는 인젝터 손상의 원인을 규명하여 안정적인 인젝터 설계에 도움을 주기 위한 목적으로 실험용 동축 인젝터를 제작하여 화염 부상 특성을 실험적으로 연구하였다. 사용된 인젝터는 연료인 Kerosene을 접선형 선회기로부터 90$^{\circ}$의 원뿔 각을 가지고 분무되도록 설계하였으며, 그 주위로 산하제인 GO$_2$가 연소실의 축방향에 수평하게 분무되도록 설계하였다. 2-유체 동축 인젝터의 난류 확산 화염에서 연료와 산화제의 혼합은 화염 특성을 결정하는 주요 변수이므로 인젝터로부터 분무되는 추진제간의 유량을 변화시켜 화염 부상 특성을 연구하였다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.11a
• /
• pp.257-258
• /
• 2019

이 연구는 기 개발한 간이 선박조종 시뮬레이터의 조종성능 개선에 관한 것이다. 선박조종 시뮬레이터에서 모델선박의 조종성 지수는 임의로 정하는 것이 아니라 가능한 모델대상선박의 실제 움직임과 동등하거나 유사하게 설정되어야 한다. 선행연구에서는 이미 발표된 대학교 실습선(한바다호)의 선박조종 실선데이터를 기반으로 모델선박의 조종성 지수를 도출하였으나, 타각이 10°를 초과할 경우 네 종류의 실선시험 결과와 평균 17.9%의 상대오차가 발생하였다. 이에, 타각 10°, 20° 및 35°에서의 한바다호 조종성 지수에 대해 에르미트 보간을 이용하여 3차 다항식을 산출하고, 이를 모델선박에 적용하였다. 그 결과 타각 35° 이내의 전 구간에서 조종성능의 상대오차가 평균 13.7%에서 11.6%로 약 2.1% 개선됨을 확인하였다.

• Journal of the Korean Institute of Gas
• /
• v.14 no.3
• /
• pp.1-7
• /
• 2010

According to Indoor Air Quality(IAQ) management law for multi-use buildings, SEEONE CO., Ltd. made pilot and tested it to remove minute particle, odor, VOCs, etc. within the standards of IAQ. This pilot made by SEEONE CO., Ltd. is vortex scrubber washing electrolyzed water. As 30 minutes test result in multi-use building indoor place, minute particle(the smoke of a cigarette) was reduced $920{\mu}g/m^3{\rightarrow}112{\mu}g/m^3$, gaseous contaminants was reduced Formaldehyde (HCHO) 20ppm$\rightarrow$4ppm, Ammonia($NH_3$) 50ppm$\rightarrow$1ppm, Trimethylamine ($(CH_3CH_2)_3N$) 15ppm$\rightarrow$trace, Methylethylketone($CH_3COC_2H_5$) 25ppm$\rightarrow$trace, Acetic acid ($CH_3COOH$) 20ppm$\rightarrow$trace, Acetaldehyde($CH_3CHO$) 15ppm$\rightarrow$2ppm and Acetone($CH_3COCH_3$) 50ppm$\rightarrow$N.D. The pilot test result of the air filter using electroyzed water in vortex scrubber showed high removal efficiency. Because purified air maintain indoor humidity of approximately 40~60%, so users can feel pleasant. In E.coli, S.aureus sterilization test and CODcr, turbidity treatment test by electrolysis, germs was sterilized over 99.99% and CODcr and turbidity was decreased gradually. So water used for washing can be reused by electrolysis.