• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2018.05a
• /
• pp.185-186
• /
• 2018

에어보트(Air boat)는, 판옥선처럼 선체 밑바닥이 편평한 형태로 되어있어 물위는 물론 일반 선박이 갈 수 없는 얕은 수면, 개펄, 빙상, 늪지수풀 위를 달릴 수 있는 모터보트의 한 종류이다. 선체상부 뒤쪽에 장착된 로터의 회전에 의한 풍력으로 추진되며, 로터 바로 뒤에 방향키가 있다. 선체 재질로는 스틸, FRP가 주로 사용되고 있으며 최근 알루미늄, 탄소섬유의 적용이 늘어나고 있다. 수상크루징, 낚시, 스쿠버 등에 활용되며, 선저의 독특한 형상으로 인해 군사용, 인명구조용, 수산물수송용 등으로도 사용된다. 이 연구에서는 12인승 비미니탑 에어보트를 설계, 제작하고 해상 시운전을 실시하였다. 또한 소음저감을 위해 머플러를 설계 제작하고, 35노트에서 75~78dB 수준으로 성능을 검증하였다.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.31 no.4
• /
• pp.22-25
• /
• 1994

선체성능, 선박운항성능 및 기관성능의 현황파악과 예측을 하는 것은 선박설계자, 선박운항자 및 선박관리운영자에게 설계, 보선관리 및 용역관리상 대단히 중요하다. 선체성능의 전산원용예측에 관한 대부분의 문헌은 모형수조시험 및 공시해상시험의 자료를 수식화하는 데 집중하고 있다. 따라서 현재까지 자료의 수식화, 예측된 자료와 성능시험결과치의 상관기법 및 PC soft ware를 이용한 선박성능예측의 체계적 접근법 등에 관한 연구가 활발히 진행되어 왔다. 또한 선박의 Abstract Log Book의 자료 및 주기관 성능자료의 수식화, PC soft ware 개발에 의한 선박운 항성능 및 기관성능예측에 대한 연구가 역시 수행되고 있다. 이와 관련하여 본 고에서는 선체 성능(저항과 추진계수), 선박운항성능 및 주기관성능의 예측에 관하여 그 개요를 소개코져 한다.

• 해운
• /
• no.4 s.15
• /
• pp.32-32
• /
• 2005

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.6
• /
• pp.587-593
• /
• 2020

The securing safety of ferry ships on the domestic coast is evaluated by comparing the external force applied and the securing device based on the cargo weight and hull acceleration that can exist at the loaded position. The hull acceleration based on the domestic standard, which is the basis for securing safety evaluation, is applied without reflecting the characteristics of the ship and the sailing conditions. In this study, a total of 12 acceleration measurements were performed at four points of the hull of a ship with a DWT 6,800 ton class 15.5 knots passing through Busan-Jeju to analyze the hull acceleration of the domestic coastal ferry ship. Data were collected for the buoy. For a theoretical comparative analysis of the limited measurement results, the response amplitude operator (RAO) was analyzed through frequency-response analysis by numerical simulation, and acceleration analysis for the four points was performed using the RAO results. Based on the acceleration comparison, differences in the degree of each position were observed, but in the case of the Y-axis acceleration, the analysis was 1.81 m/s², and the measurement was 1.47 m/s². The analyzed simulation result was as high as 0.34 m/s². Moreover, analysis was performed at 22 % level, and measurement at 18 % level.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.674-680
• /
• 2013

As the range of marine leisure activity gradually expands to ocean-going, a habitable cruise boat has been getting the limelight. Advanced countries in the marine leisure industry in Europe and North America have already secured their competitiveness in designing and building cruise boats by elegant design, ergonomic structure and fuel efficiency through the adoption of light-weight hull materials. In contrast, mostly small power boats are developed and built in Korea, and GFRP take up the most of hull materials. This study inquired into the design and characteristics of a 50ft-class CFRP that ocean-going is possible. The hull-form of the CFRP cruise boast were analyzed to propose a hull form for the designed ship (MMU-C.B), and based on that, the design model of the MMU-C.B was built. Finally, the MMU-C.B's characteristics of the resistance performance and hull-planing were found by comparative reviews with the results of model tests of GFRP pleasure yachts.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.2
• /
• pp.219-226
• /
• 2020

Nondestructive testing is one of the most commonly used quality inspection methods for evaluating ship structures. However, accurate evaluation is dif icult because various composite materials, such as reinforcements, resin, and fiber-reinforced plastics (FRPs), are used in hulls, and manufacturing quality differences are likely to exist owing to the fabrication environment and the skill level of workers. This possibility is especially true for FRP ships because they are significantly thicker than other structures, such as automobiles and aircraft, and are mainly manufactured using the hand lay-up method. Because the density of a material is a critical condition for ultrasonic inspection, in this study, a hull plate was selected from a vessel manufactured using e-glass fiber, which is widely used in the manufacture of FRP vessels with the weight fraction of the glass content generally considered. The most suitable ultrasonic testing conditions for the glass FRP hull plate were investigated using a pulse-echo ultrasonic gauge. A-scans were performed with three probes (1.00, 2.25, and 5.00 MHz), and the results were compared with those of the hull plate thickness measured using a Vernier caliper. It was found that when the probe frequency was higher, the eco-pulse velocity of the receiver had to be lowered to obtain accurate measurement results, whereas fewer errors occurred at a relatively low probe frequency.

• Journal of Navigation and Port Research
• /
• v.29 no.6 s.102
• /
• pp.515-522
• /
• 2005

The ship plating is generally subjected to. combined in-plane load and lateral pressure loads, In-plane loads include axial load and edge shear, which are mainly induced by overall hull girder bending and torsion of the vessel. Lateral pressure is due to. water pressure and cargo. These load components are nat always applied simultaneously, but mare than one can normally exist and interact. Hence, far mare rational and safe design of ship structures, it is af crucial importance to. better understand the interaction relationship af the buckling and ultimate strength far ship plating under combined loads. Actual ship plates are subjected to relatively small water pressure except far the impact load due to. slamming and panting etc. The present paper describes an accurate and fast procedure for analyzing the elastic-plastic large deflection behavior up to. the ultimate limit state of ship plates under combined loads. In this paper, the ultimate strength characteristics of plates under axial compressive loads and lateral pressure loads are investigated through ANSYS elastic-plastic large deflection finite element analysis with varying lateral pressure load level.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.61-67
• /
• 2005

The ship plating is generally subjected to combined in-plane load and lateral pressure loads. In-plane loads include axial load and edge shear, which are mainly induced by overall hull ginder bending and torsion of the vessel. Lateral pressure is due to water pressure and cargo. These load components are not always applied simultaneously, but more than one can normally exist and interact. Hence, for more rational and safe design of ship structures, it is of crucial importance to better understand the interaction relationship of the buckling and ultimate strength for ship plating under combined loads. Actual ship plates are subjected to relatively small water pressure except for the impact load due to slamming and panting etc. The present paper describes an accurate and fast procedure for analyzing the elastic-plastic large deflection behavior up to the ultimate limit state of ship plates under combined loads. In this paper, the ultimate strength characteristics of plates under axial compressive loads and lateral pressure loads are inverstigated through ANSYS elastic-plastic large deflection finite element analysis with varying lateral pressure load level.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.1
• /
• pp.129-137
• /
• 2016

In the present study we verified performance of feed-forward control algorithm using short term prediction of ship motion information by taking advantage of developed numerical simulation model of FPSO motion. Up until now, various studies have been conducted about thrust control and allocation for dynamic positioning systems maintaining positions of ships or marine structures in diverse sea environmental conditions. In the existing studies, however, the dynamic positioning systems consist of only feedback control gains using a motion of vessel derived from environmental loads such as current, wind and wave. This study addresses dynamic positioning systems which have feedforward control gain derived from forecasted value of a motion of vessel occurred by current, wind and wave force. In this study, the future motion of vessel is forecasted via Brown's Exponential Smoothing after calculating the vessel motion via a selected mathematical model, and the control force for maintaining the position and heading angle of a vessel is decided by the feedback controller and the feedforward controller using PID theory and forecasted vessel motion respectively. For the allocation of thrusts, the Lagrange Multiplier Method is exploited. By constructing a simulation code for a dynamic positioning system of FPSO, the performance of feedforward control system which has feedback controller and feedforward controller was assessed. According to the result of this study, in case of using feedforward control system, it shows smaller maximum thrust power than using conventional feedback control system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.6
• /
• pp.744-750
• /
• 2015

In this paper, development of mobile robot for the inspection of hull surface was mentioned. In the sea, it is difficult to proceed with the visual inspection of hull side and thus mobile robot for checking the status could be run with strap-on its surface. To do this, permanent magnet module to generate magnetic force between hull surface and mobile robot, and structure to minimize variance of the force under curvature circumstance were considered on the design. Based on the design, mobile robot with four NdFeB, four driving wheels and image aquisition module was applied. Load experiment to check the adhesive force, slip test during stop state and driving test to measure driving speed were executed. From the experiments 13 Kgf adhesive force was obtained and slip was not happened until 8 Kgf load on the inclined plate. Driving speed of mobile robot was measured at 0.82 m/s corresponding to 6.5 ampere. We confirmed the effectiveness of developed mobile robot by experiments to check its characteristics.