• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.479-485
• /
• 2004

The interest of ACT (Automated Container Terminal) is increasing because of expansion of container's transportation quantity, appearance of large-sized and. high-speed vessel, high labor cost of container terminal and the change of technical level. Therefore, the ACT had been developed in several ports in the world, such as ECT (Europe Combined Terminals) and CTA (Container Terminal Altenwerder). They have studied detailed technique for the operation of ACT. In Korea, it also has increased not only expansion and improvement of container terminal, but also necessity of ACT. Now, many projects related to the development of ACT are working in Korea. And the technical improvement of operating system, automated equipments and information system has accomplished by the projects. The ACT consists of the basic equipment and the integrated information system for operating and controlling automated equipments. The productivity of ACT is maximized through efficient connection between them. Thus, the automated degree of container terminal is dependent on the developing time of operating system, reliability, transportation quantity of container, investment amount and technical level. In this paper, we propose important strategy in developing ACT through analyzing the property of each ACT.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.3
• /
• pp.202-208
• /
• 2017

The recently developed marine engines for propulsion of ships have higher torsional exciting force than previous engines to improve the propulsion efficiency and to reduce specific fuel oil consumption. As a result, a viscous damper or viscous-spring damper is installed in front of marine engine to control the torsional vibration. In the case of viscous damper, it is supposed that there is no elastic connection in the silicon oil, which is filled between the damper housing and inertia ring. However, In reality, the silicon oil with high viscosity possesses torsional stiffness and has non-linear dynamic characteristics according to the operating temperature and frequency of the viscous damper. In this study, the damping characteristics of a viscous damper used to control the torsional vibration of the shafting system have been reviewed and the characteristics of torsional vibration of the shafting system equipped with a corresponding viscous damper have been examined. In addition, it is examined how to interpret the theoretically optimal dynamic characteristics of a viscous damper for this purpose, and the optimum design for the propulsion shafting system has been suggested considering the operating temperature and aging. when the torsional vibration of the shafting system is controlled by a viscous damper filled with highly viscous silicon oil.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.3
• /
• pp.89-99
• /
• 1990

It is required to develop a hull form with low resistance and high propulsive efficiency for the improvement of the ship-board operational economy. Since the hull forms with low resistance frequently have lower propulsive efficiency and on the other hand the hull forms with higher propulsive efficiency don't show good resistance characteristics, it is always very difficult to obtain economical hull forms which require less propulsive power accordingly. Efforts have been made to pursue a stern form with excellent resistance and propulsion characteristics together by shaping the run of the so-called buttock-flow type stern, which is known to have good viscous resistance performance, like that of conventional aftbody(U-type or Hogner type) featured by high propulsive efficiency. First model tests confirmed that the above concept can be one of the alternative approaches to the design of the good stern form and by the continuing efforts thereafter for the refining of the concept, propelled by the first promising results, stern form of good resistance performance together with good propulsive efficiency has been realized to some extent. In addition, it is confirmed that the new new stern can have better cavitation and vibration characteristics due to uniform wake-fields and the compact engine room arrangement can be possible due to it's larger floor area in way of engine room double bottom as compared with usual barge stern.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.121-126
• /
• 2013

Cycloconverter used as a power conversion device in the speed and torque control system of AC machines has the advantage of a simple control and a large torque at low speed. In addition, because a rectifier, a DC link, and an inverter are not installed, this system is simple and suitable for large power system. If a power conversion device, which is currently used as a propulsion motor of large vessel, is changed into cycloconverter, the system is simplified and then the installation costs can be significantly reduced. However, conventional cycloconverter has the increased harmonics because the power loss is large and the waveform of output voltage is distorted, due to the high-speed switching of power semiconductor devices. In order to improve these shortcomings, this paper describes a phase shifting filter which is composed of two inputs with different phases in the primary side and one output in the secondary one. As the voltage waveforms with two different phases are added and transformed into the secondary side, these outputs are close to sinusoidal waves. Thereby the voltage waveforms, which are applied to the propulsion motors, are improved and total harmonic distortions (THDs) are significantly reduced.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.301-306
• /
• 2016

During the initial stage of propulsion shaft design, the shaft alignment process includes a thorough consideration of lateral vibration to verify the operational safety of the shaft. However, a theoretical method for analyzing forced lateral vibrations has not been clearly established. The methods currently used in classification societies and international standards can only ensure a sufficient margin to avoid the blade-passing frequency resonance speed outside the range of ${\pm}20%$ of the maximum continuous rating (MCR) for the engine. Typically, in shaft alignment analyses, longer center distances between the support bearings promote affirmative results, but the blade order resonance speed can approach the lower limit for lateral vibration. Therefore, this matter requires careful attention by engineers, and a verification of the theoretical analysis by experimental measurements is highly desirable. In this study, both theoretical and experimental analyses were conducted using strain gauges under two draught conditions of vessels used as 50,000-DWT oil/chemical tankers, introduced recently as eco-friendly ships. Based on the analyses, the influence of the lateral vibration on the shafting system and the system's reliability was reviewed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1057-1063
• /
• 2014

Concerning $CO_2$ reduction from International Societies, lots of laboratories and relevant societies suggest many reports on how to reduce fuel consumption from their specific ways. Undoubtedly, cutting costs is the final desired destination for owner outcome, but many questions there are on the way yet: how is this measure working? how efficient is it? On what size of ship would it work best and be the most effective? etc. Fuel cost is one of the major cost elements for ship owners and/or operators. And by reducing fuel consumption owners and/or operators will reduce both their costs and the environmental impact from their ship. This paper is aim to address how the measures work for saving fuel consumption through improve propulsion efficiency, installation cost and benefit can be calculated easily in the return on investment for estimated one year operation, and finally their compatibility with other fuel saving measure devices.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.11a
• /
• pp.197-198
• /
• 2019

Competition between global ports is intensifying as the number of calling ports has decreased due to the growth of ship size and the implementation of global environmental regulations has begun. Global ports are pushing for a strategic and concrete transition to smart ports in order to secure port competitiveness in the future. In Korea, however, the government plans and projects for promoting smart ports have yet to materialize, and related papers and research are lacking. In this paper, the concept of smart port was established, and the current status of technology and introduction of smart ports was analyzed. In addition, the concept of Smart Port Index(SPI) was presented in order to objectively and quantitatively compare the level of smartness. As a result,

• Journal of Navigation and Port Research
• /
• v.44 no.6
• /
• pp.477-487
• /
• 2020

The inefficient operation of Busan New Port is due to container-terminal operators being dispersed in small groups, rather than being integrated. This dispersion increased following the reorganization of global shipping alliances in 2016 and causes unnecessary Inter-terminal Transportation(ITT) and ship delays. Studies of integrated operations for larger container terminals show that integration is not going well, however, due to the pre-emptive task that follows the integrated operation. Therefore, in this study, we divided the integrated operation into stages based on a simulated model of the container terminals in Busan New Port. The simulation took into account future increases in the ship's enlargement and terminal congestion, and the operational effects of each type of integrated operation were analyzed and evaluated.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.12-18
• /
• 2021

In this study, the performance modeling of MT30 gas turbine engine is performed. The design point is determined, and the component performance maps to which the scaling technique is applied are generated using standard maps provided by the commercial program. Off-design point performance analysis is performed with the generated performance model, and this is compared with the performance deck data of the engine. It is confirmed that the data of the performance maps generated by the one-point scaling method had some errors from the performance deck data, and it is determined that correction is necessary to increase the accuracy of the performance model. Therefore, the off-design point analysis is performed by creating the correction performance model in a manner that obtains the scaling factors for each operating point(off-design point) according to the high pressure spool speed.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.3
• /
• pp.158-166
• /
• 2021

In this paper, a numerical analysis technique using a body force model is investigated to estimate the available net thrust of multi-pod-driven ice-breaking vessels under bollard pull and overload conditions. To employ the body force model in present flow simulations, drag and thrust components acting on the pod unit are calculated by using Propeller Open Water (POW) test data. The available net thrusts according to the direction of operation are evaluated in both bollard pull and overload conditions under deep water. The simulation results are compared with the model test data. The available net thrusts, calculated by the present analysis for ahead operating modes at 3~6 knots which are typical speeds of the target vessel in arctic field, are agreed well with the model test results. It is also found that the present result for astern operating mode appears approximately 6 % larger than the model test result. In addition, the available net thrusts are calculated under the both operating conditions accompanied by shallow water effects, and the main cause of the difference is studied. Based on the result of the present study, it is confirmed that the body force model can be applied to the performance evaluation of multi-pod propulsion system and the main engine selection in early design stage of the vessel.