• Journal of the Korean GEO-environmental Society
• /
• v.23 no.2
• /
• pp.25-36
• /
• 2022

In this study, seepage control effect of relief well was evaluated quantitatively on embankment of small fill dam and levee. Seepage analysis of dam and levee were carried out according to the permeability of fill material and foundation and to analyze behaviour characteristics of seepage. The up-lift pressure at toe of embankment was analyzed which is generated by seepage according to relief well installation condition. The relief well could reduce pore water pressure which is to cause piping or up-lift pressure at foundation ground of embankment and it does not be influenced on geometric condition such as dam height and slope incline. In case of relative low permeable ground, the pore water pressure reduction effect of relief well was decreased compare with high permeable ground but it shows pore water pressure reduction effect compare with no relief well condition. The reduction effect of relief well shows relative gap according to diameter and penetration length of relief well and the installation length of relief well is the most effective factor for seepage control.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1994.06a
• /
• pp.65-71
• /
• 1994

유압 실린더용 유패킹의 접촉력, 접촉폭, 돌출발생 임계압력을 밀봉간극에 대하여 유한요소법을 이용하여 수치적으로 해석하였다. 초기 간섭량이 증가함에 따라 접촉력 및 접촉폭은 급격하게 증가하였다. 그러나 유압이 작용하는 상태에서 밀봉간극이 감소하면 시일의 돌출현상이 발생하는 임계압력은 보다 가파르게 증가함을 확인하였다. 초기 간섭량에 의한 접촉력으로 부터 유압 실린더의 누설에 관련된 사용 최저 유압을 연계하여 갑섭량이 설계되어야하고, 돌출발생 임계압력으로 부터는 사용 최고유압과 관련하여 간극이 설계되어야 하므로 이에 대한 수치해석적 설계자료를 제시하였다. 특히 시일립부의 접촉면을 나타내는 축방향에 따라서 접촉력 분포는 시일립 선단부와 돌출현상에 따른 상호 복잡한 결과의 중요성을 제시하였다. 이 결과는 윤활해석을 위한 탄성유체윤활 해석시 입력자료로 사용될 수 있어 실제 유막두께 해석 및 유동해석을 통하여 누설량 예측 등에 이용될 수 있는 설게자료이다.

• Tribology and Lubricants
• /
• v.9 no.2
• /
• pp.22-28
• /
• 1993

The experimental investigation on the inlet pressure of a large tilting pad journal bearing is studied. The continuous distribution of the film pressure and film thickness are measured along with the shaft speed and bearing load for various flow rates. Considerably large inlet pressure is observed at the entrance of each pad, especially lower pads. The inlet pressure increases with the increase of shaft speed as well as bearing load, but it is almost independent on the folw rate and the oil supply temperature. Because of the inlet pressure, the upper pads always keep up slight wedge film shape which are almost parallel to the journal surface, and spragging is not observed in the upper pads with no preload.

• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.30-38
• /
• 1994

The thermohydrodynamic(THD) performance of a large tilting pad journal bearing is investigated both theoretically and experimentally. The theory takes into account the three dimensional variation of lubricant viscosity and eddy viscosity, and the inlet pressure. Owing to the inlet pressure effect, the film pressure and load capacity are increased but the mixing temperature and bearing surface temperature are decreased. The continuous distribution of the film pressure and film thickness and the bearing surface temperature are measured along with the shaft speed and the bearing load, and they are compared with the theoretical results. The results obtained by the experiment are in good agreement with those by the theory including the inlet pressure effect. It is suggested that the three dimensional turbulent THD analysis including the inlet pressure effect is very useful to predict the performance of the large tilting pad journal bearing more accurately.

• Tribology and Lubricants
• /
• v.2 no.1
• /
• pp.61-68
• /
• 1986

Effects of the ram-pressure on the THD-performance of pivoted pad thrust bearings are investigated experimentally. A sector-shaped tilting pad thrust bearing and a rotating disk are used. Temperature distribution on the disk surface as well as on the pad surface, distribution of the pressure generated within the fluid film, and the film thickness are measured continuously in the circumferential direction after thermal equilibrium is established. The ram-pressure is proportional to the mean pressure of oil film and to the rotational speed of the disk and affects the maximum pressure and the pressure distribution. The temperature rise on the mating surface of the disc and the pad, contacting with the oil film, is proportional to to the bearing load and the disk speed. The ram-pressure and the temperature rise on the disk surface are dominant factors that affect the THD-performance of pivoted pad thrust bearings.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.68-76
• /
• 1989

In this paper, the influence of ram-pressure on the static and dynamic characteristics of infinite width tilting-pad journal bearing is investigated theoretically. The ram-pressure is obtained by assumption of conservation of mechanical energy of the lubricant flow through the leading edge of the pad. The pressure in the lubricating film is numerically calculated using the ram-pressure obtained as the inlet pressure boundary condition of the pad. The static equilibrium state of tilting-pad journal bearing is determined by Newton-Raphson iteration method. A numerical results are presented in graphic form and relationships between the ram-pressure and the static and dynamic characteristics are discussed.

• Tribology and Lubricants
• /
• v.5 no.2
• /
• pp.77-82
• /
• 1989

The influences of ram pressure on the performances of tilting-pad journal bearings are investigated experimentally. The test rig consists of a single tilting-pad and a rotating journal. Film thicknesses and pressure distribution of the lubricating film are measured continuously for several values of coordinate of the pivot position and journal speed. The findings of the investigation are as follows: (]) According as the journal speed increases the ram pressure increases, maximum pressure decreases and the pivot position which maximize the minimum film thickness shifts toward the leading edge. (2) The ram pressure makes it possible to generate the converging wedge and the positive pressure between the pad and the journal even when the pad is supported at the points between the leading edge and the center of the pad. (3) The influence of the ram pressure on the performance of tilting pad bearings is significant and must be considered in the design of these bearings.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.33-42
• /
• 1994

An influence of inlet pressure on the performance of sector-shaped pad thrust bearings is investigated theoretically. The optimum conditions of film thickness or the optimum positions of pivot are found through the evaluation of load capacity for all available conditions of film thickness, under the operating conditions which the thermal and pad deformation effects can be neglected. The bearing performance including the inlet pressure effects is obtained for a wide operating ranges that inertia parameter(Re$^{*}$) is up to unity, and for the various cases of pad extent angle (number of pad) and the three cases of the angle between pads. The results show that the inlet pressure has a large influence on the performance of sector-shaped pad thrust bearings. In the design of sector-shaped pad bearings, due to the inlet pressure, the optimum number of pad is varied with the operating speed and the angle between pads, and the optimum position of pivot is located toward the leading edge along with the operating speed increases.

• Journal of the Korean GEO-environmental Society
• /
• v.21 no.2
• /
• pp.5-13
• /
• 2020

The relief wells have been studied to be effective in seepage control in small dams such as agricultural dams. However, quantitative studies on the effects of the relief well are rare and there is no design standard also. To quantitatively analyze the effects of the seepage control in small dams, the research of up-lift pressure influencing the toe of dam body was conducted by seepage analysis, which investigates the behavior characteristics, according to the conditions of dam and foundation. The effect of seepage control was studied by analyzing the reduction effect of up-lift pressure at foundation ground of the toe of downstream dam slope depending on the installation of the relief well. As a result, it was found that the relief wells are effective in reducing the pore water pressure in the foundation, which can cause piping and sliding failure.

• Geotechnical Engineering
• /
• v.3 no.1
• /
• pp.39-52
• /
• 1987

Model pile tests are performed, first, to estimate donwndrag exerted on pile surfaces due to the settlement of surrounding soils, and, second, to evaluate the efficiency of the downdrag reduction methods such as the bitumen coating method and the method of the attachment of an enlarged base. Test results show that the downdrag forces may be expressed as 0.25(;effective overburden). Bitumen coating reduces the downdrag by more than 50 percent, and the enlarged base attachment method is also effective, whose effectiveness increases as the sixte of the base increases as expected. When the bitumen coating and enlarged base are both applied, the downdrag force is reduced as much as 90 percent. Finally, it is found that the quantity of the relative displacement between the pile and the surrounding soil downdrag is extremely small.