• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.262-267
• /
• 2000

To tap the possibility of exploiting the precipitates as flux-pinning center in the Bi-2223 superconducting system, as-received Bi-2223/Ag tapes with the starting composition of Bi$_{1.8}$Pb$_{0.4}$Sr$_2$Ca$_{2.2}$Cu$_3$O$_8$ were post-annealed at various temperature, oxygen partial pressure, and annealing time. The 2$^{nd}$ phases in the annealed specimen were analysed with XRD, SEM, TEM, and EDS. The size and the distribution of the precipitates such as (Ca,Sr)$_2$(Pb,Bi)O$_4$ and Bi$_{0.5}$Pb$_3$Sr$_2$Ca$_2$CuO$_{12+{\delta}}$ (3221) in the Bi-2223 matrix was controllable by varying heat-treatment condition without breaking the connectivity of the 2223 grains. The nano-size precipitates within the 2223 grains are conjectured as working as flux-pinning sites, resulting in increased J$_c$ value.

• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.59-64
• /
• 2010

Ferritic stainless steel is currently increasingly used for automotive exhaust material. The material for exhaust manifold is used in the temperature range of 500∼$850^{\circ}C$. Therefore, high temperature characteristic is an important one that affects it's life span. It has been investigated the effect of alloying elements of Cr, Mo, Nb, Ti in the ferritic stainless steel for exhaust manifold on the high temperature tensile strength. There was a few difference in the tensile strength at $600^{\circ}C$ with the exception of low Cr steel, but the steels containing higher Cr, Mo or Nb elements showed significantly higher tensile strength at the temperature of $800^{\circ}C$. The precipitates of the specimens after heat treating at the test temperature were electrolytic extracted, and quantitatively analysed using by SEM-EDS and TEM. The alloying elements of Cr and Mo increased the tensile strength as a solid solution strengthener, and on the other hand Nb element enhanced the strength by forming the fine intermetallic compounds such as NbC or $Fe_2Nb$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.17 no.1
• /
• pp.31-40
• /
• 1997

원자로 압력용기 재료의 중성자 조사 취화 문제는 원자력발전소의 안전성 및 수명 관리에 가장 중대 한 영향을 미친다. 재료의 조사 취화를 평가하기 위하여 수행하고 있는 충격 및 인장시험 같은 파괴적 시험 결과는 석출물 크기나 분포, 전위 밀도 등, 재료 자체의 조직학적 특성에 좌우되므로 한정된 시편을 이용한 평가에는 많은 불확실성이 존재하게 된다. 따라서 이와 같은 문제점을 해결하기 위하여 비파괴기술을 이용한 조사 취화 평가에 대한 많은 연구가 진행되고 있다. 현재 원자로 압력용기 재료의 조사 취화에 따른 미세 조직 변화를 분석하기 위하여 응용되고 있는 비파괴기술로는 전기, 자기, 전자기, 초음파 및 경도측정법 등이 있으나 비파괴피험 결과와 미세조직의 변화, 기계적 성질 및 취화 정도 등과의 상관 관계를 정립해야만 기존 파괴적 시험의 대체가 가능하게 된다. 따라서 현재까지 수행되고 있는 여러 비파괴기술을 이용한 조사 취화 평가 연구결과를 비교 분석하여 보다 실현 가능성 있는 비파괴기술을 검토하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.110-116
• /
• 2002

At elevated temperature, very complex precipitations occur in STS316. To investigate the effect of the precipitation on mechanical properties in SIS316, tensile tests and fatigue crack growth tests were carried out at $650^{\circ}C$ using artificially degraded materials. The material degradation was simulated by aging for up to 20000 hrs. at $750^{\circ}C$, which is equal to 179000hrs (about 20yrs) of service life at $650^{\circ}C$, after conducting solution treatment for 20 min. at $11300^{\circ}C$. The result of the hardness test and the tensile test showed that both properties are closely related to the mean free distance of carbides. Also, from the results of fracture tests at $650^{\circ}C$, ${\triangle}K_{th}$, after values were found to decrease as aging time and microstructure, as the volume fraction of $\sigma$ phase increased.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1000-1005
• /
• 1999

To investigate the effects of V and Sb on the recrystallization of Zr-0.8Sn alloy, the microstructure of heat-treated specimens was observed by optical microscope, SEM, and TEM. Microhardness tests were also carried out for the annealed specimens. From microstructural studies, the V or Sb additions were found to delay recrystallization process as well as grain growth. Especially, Sb was more effective in delaying the recrystallization. This delay of recrystallization and grain growth by V or Sb additions may be due to the interference in the movement of dislocation and crystal interface by V or Sb precipitates.

• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.78-86
• /
• 2002

A metallurgical model for the prediction of prior austenite grain size considering the dissolution kinetics of M$_3$C precipitates at the heat affected zone of SA508-cl.3 was proposed. The isothermal kinetics of grain growth and dissolution were respectively described by well-known equation, $dD/dT=M({\Delta}F_{eff})^M$ and Whelan's analytical model. The isothermal grain growth experiments were carried out for measure the kinetic parameters of grain growth. The precipitates of the base metal and the specimens exposed to thermal cycle were examined by TEM-carbon extraction replica method. The model was assessed by the comparison of BUE simulation experiments and showed good consistencies. However, there was no difference between the model considering and ignoring $M_3C$ precipitates. It seems considered that pinning force exerted by $M_3C$ Precipitates was lower than driving force for grain growth due to large size and small fraction of precipitates, and mobility of grain boundary was low in the lower temperature range.

• Journal of the Korean institute of surface engineering
• /
• v.19 no.2
• /
• pp.31-43
• /
• 1986

The properties of the electroless nickel deposit mainly depends on the pH of the bath, the plating temperature, and the molar ratio of nickel to hypophosphite but they are also affected by its formulation and concentration of complexing and buffering agents. According to changeing the concentration of triethanolamine and boric acid, phosphorous contents, microsturcture, crystalline, hardness and wear resistance of deposits obtained from ammoniacal alkaline bath were investigated by EPMA, differential thermal analyser, X-ray diffractometer and wear tester. The results are as follows; (1) Increasing concentration of triethanolamine in the bath, the deposits is slightly inclined to increase its phosphorous content(3.7% P). (2) In the as-plated state, the deposits are not crystallized state but they are thermally unstable phase, and they are crystallized with precipitating $Ni_3P$ at 400$^{\circ}C$. (3) The deposit containing 2.3% P has higher hardness value in the as plated and heat treated state at below 300$^{\circ}C$ than those of 3.7% phosphorous deposit (1090Hk). But in the case of heat treating at 400$^{\circ}C$, the former has lower hardness value (1000Hk) than the latter and has remarkably Ni(III) orientation by heat treatment. (4) The 3.7% phosphorous deposit heat treated at 400$^{\circ}C$ has better wear resistance than hard chromium plating.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.4
• /
• pp.453-459
• /
• 2004

25Cr-20Ni series strainless steels have an excellent high temperature strength high oxidation and high corrosion resistance. However, further improvement can be expected of creep strength by work hardening prior creep. In the present study, the effect of prestraining at room temperature on the creep behavior of a Class M(STS310S) and a Class A(STS310J1TB) alloy containing precipitates have been examined. Prestaining was carried out at room temperature and range of prestrain was 0.5-2.5 % at STS310J1TB and 2.0-7.0% at STS310S. Creep behavior and creep rate of pre-strained specimens were compared with that of virgin specimens. Room temperature prestraining produced the creep life that is longer than that of a virgin specimen both for STS310J1TB and STS310S when creep test was carried out at the temperature lower than recrystallization temperature. The reason for this improvement of creep life was ascribable to the interaction between dislocations and precipitates in addition to the dislocation-dislocation interaction in STS310J1TB and the dislocation-dislocation interaction in STS310S. The beneficial effect of prestraining in STS310J1TB was larger than that of STS310S.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.5
• /
• pp.231-236
• /
• 2018

The purpose of this study was to investigate the microstructural characteristics and hardness distribution of AZ91 magnesium alloy furnace-cooled to room temperature after solution treatment, and to compare the results with those of as-cast condition. The as-cast alloy showed a partially divorced eutectic ${\beta}(Mg_{17}Al_{12})$ phase and discontinuous precipitates (DPs) with a lamellar morphology, while only DPs were observed in the furnace-cooled alloy. The DPs in the furnace-cooled AZ91 alloy had various apparent interlamellar spacings, which would be ascribed to the different transformation temperatures during the furnace cooling. The average hardness for the furnace-cooled alloy is similar to that for the as-cast alloy. It is interesting to note that the hardness values of the furnace-cooled alloy were distributed over a narrower range than those of the as-cast alloy. This is likely to be caused by the relatively more homogeneous microstructure of the furnace-cooled alloy in comparison with the ascast one.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.6
• /
• pp.271-276
• /
• 2020

The relationship between the hardness and interlamellar spacing of discontinuous precipitates (DPs) formed by continuous cooling was studied for Mg-9%Al-1%Zn alloy. After solution treatment at 683 K for 24 h, the specimens were cooled to room temperature with different cooling rates ranging from 0.2 to 2 K·min^-1, in order to obtain DPs with various interlamellar spacings. It was found that cooling rate of 2 K·min^-1 yielded only small amount of nodular DPs at the grain boundaries, while cooling rates below 2 K·min^-1 yielded both DPs and continuous precipitates (CPs). The volume fraction of DPs increased with increasing cooling rate up to 0.5 K·min^-1, over which it abruptly decreased. The hardness of DPs was increased with an increase in the cooling rate, whereas the interlamellar spacing of the DPs was decreased with respect to cooling rate. The hardness of the DPs formed by continuous cooling was correlated with the interlamellar spacing and can follow a Hall-Petch type relation as in the case of pearlite with lamellar morphology.