• 한국재료학회지
• /
• 제12권10호
• /
• pp.825-830
• /
• 2002

The growth rate of solid grains in TiC-XC-2vol% and TiC-XC-30vo1% Ni cermets, where X=Zr, W or Mo, was fitted to an equation of the form $d^3$-$do^3$=Kt. The grain growth behavior during liquid phase sintering at 1673K decreased markedly with addition of $Mo_2$C or WC and increased with addition of ZrC. The contiguity ratio was greater in the alloys with smaller growth rate constant and decreased with increasing Ni content in the $TiC-Mo_2$C-Ni cermet. The grain growth mechanism could be explained by the effect of contiguous grain boundaries in restricting the overall grain growth.

• 한국자동차공학회논문집
• /
• 제4권5호
• /
• pp.223-230
• /
• 1996

The quality and productivity in machining automobile parts are influenced by various factors such as cutting conditions, vibration, and used tool. To improve the quality and productivity of the automobile parts(torsion beam), lots of research on the evaluation of tool life and control of surface roughness has been required. Therefore, the width of flank wear, cutting force, and surface roughness are monitored to analyse the characteristics of tool wear and surface roughness at different tools. This experimental investigation is mainly focused on the characteristics of the tool wear, tool life and surface roughness in multi-insert milling of automobile parts(torsion beam) by using uncoated tungsten carbide tool(WC), TiN coated tool, and cermet tool.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.8-12
• /
• 2012

Recently, a wide range of industrial production area has a competitive advantage through cost reduction. Moreover with the development of industrial technology, base material and cutting tool help the machining technology. But most of the machining enterprises have not hold the R&D facilities and human resources. This mainly disturbs the industrial development and th increase of production efficiency. Especially in the interrupted machining process, it showed different behavior with continuous machining process. So it needs to research and develop the tool life and tool wear mechanism analysis.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.95-103
• /
• 2001

The properties of the detonation sprayed cermet coating are investigated through the mechanical, corrosion and erosion test. The test results are also compared with the properties of the substrate materials, STS 329J1, dual phase stainless steel and the plasma sprayed cermet coatings. The two kinds of carbide cermet power, WC+NiCr, Cr$_3$C$_2$+NiCr were used in this experiment. The experimental results showed that the anti-corrosive and anti-erosive properties of the detonation sprayed cermet coatings are superior to the plasma sprayed cermet coatings. The WC+NiCr cermet coating appears to be more effective than Cr$_3$C$_2$+NiCr cermet coating in abrasive erosion environment, whereas the Cr$_3$C$_2$+NiCr cermet coatings are more effective in cavitation erosion environment.

• 한국분말재료학회지
• /
• 제6권2호
• /
• pp.139-144
• /
• 1999

The pure Ti, Ni and carbon powders were reaction milled to synthesize the TiC-Ni based cermet powders with ultrafine microstructures. After milling, the ultrafine TiC or amorphous Ti-Ni phase was obtained, respectively, according to the milling condition. The effects of milling variables on the synthesizing behavior of the powders were investigated in detail. The sintered TiC-Ni based cermet of the reaction milled powders consisted of very fine TiC of 0.2~1.5$\mu$m, as compared with that of a commercial cermet of 3~5$\mu$m. This demonstrates the potenial of reaction milling as an effective processing route for the preparation of cermet materials.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.350-353
• /
• 2005

It is a feature of primary importance for a backing material for circular saw blades having teeth which are tipped with cermet, that the steel has not a too high hardenability in order that the backing material shall not be completely hardened through brazing, welding or grinding, etc. in connection with the finishing operation in the manufacturing of circular saw blade. It is believed that V-(2Mo+W) added steel from this point of view had best conditions. Using V-(2Mo+W) added backing steel, the tool failure can be effectively prevented due to superior damping performance.

• 한국재료학회지
• /
• 제24권10호
• /
• pp.526-531
• /
• 2014

Thermal shock resistance property has recently been considered to be one of the most important basic properties, in the same way that the transverse-rupture property is important for sintered hard materials such as ceramics, cemented carbides, and cermets. Attempts were made to evaluate the thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermets using the infrared radiation heating method. The method uses a thin circular disk that is heated by infrared rays in the central area with a constant heat flux. The technique makes it possible to evaluate the thermal shock strength (Tss) and thermal shock fracture toughness (Tsf) directly from the electric powder charge and the time of fracture, despite the fact that Tss and Tsf consist of the thermal properties of the material tested. Tsf can be measured for a specimen with an edge notch, while Tss cannot be measured for specimens without such a notch. It was thought, however, that Tsf might depend on the radius of curvature of the edge notch. Using the Tsf data, Tss was calculated using a consideration of the stress concentration. The thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermet increased with increases in the content of nitrogen and Ni. As a result, it was considered that Tss could be applied to an evaluation of the thermal shock resistance of cermets.

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.648-653
• /
• 2012

Hybridization of dense ceramic membranes for hydrogen separation with an electronically conductive metallic phase is normally utilized to enhance the hydrogen permeation flux and thereby to increase the production efficiency of hydrogen. In this study, we developed a nickel and proton conducting oxide ($BaCe_{0.9}Y_{0.1}O_{3-{\delta}}$: BCY) based cermet (ceramic-metal composites) membrane. Focused on the general criteria in that the hydrogen permeation properties of a cermet membrane depend on its microstructural features, such as the grain size and the homogeneity of the mix, we tried to optimize the microstructure of Ni-BCY cermets by controlling the fabrication condition. The Ni-BCY composite powder was synthesized via a solid-state reaction using $2NiCO_3{\cdot}3Ni(OH)_2{\cdot}4H_2O$, $BaCeO_3$, $CeO_2$ and $Y_2O_3$ as a starting material. To optimize the mixing scale and homogeneity of the composite powder, we employed a high-energy milling process. With this high-energy milled composite powder, we could fabricate a fine-grained dense membrane with an excellent level of mixing homogeneity. This controlled Ni-BCY cermet membrane showed higher hydrogen permeability compared to uncontrolled Ni-BCY cermets created with a conventionally ball-milled composite powder.

• 한국재료학회지
• /
• 제32권1호
• /
• pp.44-50
• /
• 2022

Transition metal carbides (TMCs) are used to process difficult-to-cut materials due to the trend of requiring superior wear and corrosion properties compared to those of cemented carbides used in the cutting industry. In this study, TMC (TiC, TaC, Mo₂C, and NbC)-based cermets were consolidated by spark plasma sintering at 1,300 ℃ (60 ℃min) with a pressure of 60 MPa with Co addition. The sintering behavior of TMCs depended exponentially on the function of the sintering exponent. The Mo₂C-6Co cermet was fully densified, with a relative density of 100.0 %. The Co-binder penetrated the hard phase (carbides) by dissolving and re-precipitating, which completely densified the material. The mechanical properties of the TMCs were determined according to their grain size and elastic modulus: TiC-6Co showed the highest hardness of 1,872.9 MPa, while NbC-6Co showed the highest fracture toughness of 10.6 MPa^*m^1/2. The strengthened grain boundaries due to high interfacial energy could cause a high elastic modules; therefore, TiC-6Co showed a value of 452 ± 12 GPa.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.204-211
• /
• 2020

경질 크롬 도금은 도금과정에서 유독성 물질인 Cr⁺⁶을 배출시키기 때문에 환경오염과 폐암을 유발하고 있어 최근 고속화염 용사법 (HVOF)을 이용한 코팅 방법이 대체 방법으로 각광받고 있다. 본 연구에서는 HVOF 방법을 이용하여 경질 크롬 도금 방법을 대체하기 위한 WC-CoCr과 WC-CrC-Ni 서멧 코팅을 제조하였으며, 제조된 코팅층의 물리적/화학적 특성인 미세경도, 기공도, 결정상 및 미세구조를 경도기, 광학현미경, X-선 회절 (XRD), 주사전자현미경(SEM) 및 EDS를 이용하여 분석하였다. 코팅층의 마모 및 마찰 거동 분석을 위해 왕복 슬라이딩 마모 테스트 방법을 이용하여 25 ℃, 250 ℃, 450 ℃의 온도에서 실시하였으며, 두 코팅층의 마모/마찰 특성을 비교 평가하여, 코팅층의 내마모 성능이 미세구조와 금속기지 결합제 간의 연관성이 있음을 확인하였다. 결과적으로 미세구조가 균일하고, 기공도가 낮을수록 내마모성이 향상되고, 금속기지 결합제가 많을수록 우수한 내마모성을 나타내는 것으로 확인되었다. 즉, 균일한 미세구조와 과량의 Co, Cr 금속기지 결합제, 낮은 기공도로 인해 온도와 테스트 온도와 관계없이 WC-CoCr 코팅이 WC-CrC-Ni 코팅에 비해 내마모성이 우수한 것으로 나타났다.