• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.853-856
• /
• 2004

This study presents a prediction method for sound insulation of sandwich plate which consists of orthotropic plates as skin and mineral wool as core. Prediction by classic theory, which considers orthotropic effects, requires considerably complex and cumbersome process and moreover many assumption. However, experimental results of the sandwich plate with orthotropic plates as skin show that the orthotropic effects are disappeared or fade out. Hence, predictions by using sandwich model are conducted by a simple modelling that substitutes an orthotropic plate into an equivalent flat plate. Comparative results show that sandwich model gives a good agreements with theoretical prediction.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.110-122
• /
• 1996

본 논문에서는 전기유동유체(Electro-Rheological Fluid : ERF)를 함유하는 지능구조물의 동적 모델링 및 진동제어를 수행하였다. 먼저 실리콘 오일을 기본용매로 하여 조성된 ERF의 복소 전단모듈러스를 전장부하와 가진 주파수의 함수로 동적 회전모드 실험을 통하여 도출한 후, 이를 샌드위치 보 이론과 연계하여 동적 모델링을 실시하였다. 도출된 6차 편미분방정식 형태의 지배 방정식을 유한요소 모델로 이산화하여 전장부하에 따른 지능구조물의 동탄성 특성값인 감쇠 고유 주파수 및 모달 손실계수를 주파수 영역에서 얻었다. 그리고 ERF를 함유한 샌드위치 형태의 지능구조물을 제작한 후 실험적으로 얻은 동탄성 특성값과 모델에 의해 예측된 동탄성 특성값을 비교 고찰하여 제시된 동적 모델에 대한 타당성을 입증하였다. 또한 모델을 통해 전장부하 함수로 예측된 주파수 응답곡선 중에서 각 주파수 대역에 대해 최소 변위가 되는 응답곡선을 요구응답으로 설정한 후, 그에 해당하는 전장부하를 선정하는 논리적인 능동 진동제어 알고리즘을 제안하였다. 제어알고리즘의 유용성을 입증하기 위해 실험적으로 수행된 능동 진동제어 결과를 주파수영역과 시간영역에서 제시하였다.

• Composites Research
• /
• v.16 no.3
• /
• pp.18-24
• /
• 2003

Sandwich structures have been widely used in the applications of vessel industry, where high structural stiffness is required with small addition of weight. It is so significant to think of the effect of the variables in the design process of the sandwich structure for the concentrated loads. This paper describes the influence of design variables, such as core density, core thickness and face thickness ratio, on the strength of sandwich beam. The theoretical failure loads based on the 2-D elasticity theory agree well with the experimental yield or failure loads, which are measured at the three point bending laboratory test using AS4/3501-6 facing and polyurethane foam core sandwich beam. The comparison of those yield or failure loads was also done with the ratio of the top to bottom face thickness. The theoretical optimum condition is obtained by finding the intersection point of failure modes involved, which gives optimum core density of the sandwich beam for strength and stiffness. In the addition, the effect of unequal face thickness for the optimized and off-optimized sandwich beams for the strength was compared with the ratio of loading length to beam length, and the variations of strength and stiffness were discussed with the relative ratio of core to face mass.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.77-84
• /
• 2007

In this paper presented, a design method of sandwich slab bridge of simple supported made by composite materials. Many of the bridge systems, including the girders and cross-beams, and concrete decks behave as the special orthotropic plates. Such systems with sections, boundary conditions other than Navier or Levy solution types, or with irregular cross sections, analytical solution is very difficult to obtain. Thus, Finite Difference Method is used for analysis of the pertinent problem. For the design of bridge made by the composite materials, cross-section is used the form-core shape because of this shape is economical and profitable, and for output of the stress value used F.D.M. Based the experimental of a composite specialist, an equation expressing the rate of decrease of tensile strength of glass fibers based on increase of mass was obtained. From these equations, one can estimate the rate of tensile strength reduction due to increased size. Tasi-Wu failure criterion for stress space is used. Strength-failure analysis procedure, using these reduced tensile strength, is presented.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.1
• /
• pp.88-97
• /
• 1998

Large aluminium extrusions can be used in rolling stocks and high speed vessels to reduce weight and labor cost. As sandwich plates with corrugated core have enough strength in transverse and longitudinal direction, welding lines to connect members are reduced and transverse members to strength longitudinal members are not required. However, for proper design of aluminium extrusion plates, understanding of structural behaviors of the exclusions are necessary. In this paper, at first, detailed finite element analysis is carried out to understand structural behavior. And then, simple theoretical formulas for design purpose are proposed using the orthotropic plate theory. Shear stresses resulting from end twisting which is characteristics of deep aluminium extrusion plates can also be calculated by the simple theoretical formula. Comparison with the results by detailed finite element analysis shows good accuracy of the proposed simple formulas. The simple formulas can be useful in repetitive analysis in the initial design stage.