Proceedings of the Korean Society of Propulsion Engineers Conference
/
2012.05a
/
pp.106-109
/
2012
It was designed and tested ignition that an oxidizer rich preburner for a staged combustion cycle liquid rocket engine propelled by kerosene and LOx. Operation conditions of the preburner are about 60 of OF ratio and 20 MPa of combustion pressure. Ignition characteristics were compared by propellants flowrate. As the results, the higher propellants flowrate, the shorter the ignition delay time and the higher ignition stiffness. The ignition delay time was affected by incoming the oxidizer flowrate through the refrigerative cooling channels. The oxidizer flowrate from the cooling channels decreased by inflow of combustion gas during initial ignition. The oxidizer flowrate of the cooling channels increases, it is rapid recovery by cooling effect, eventually the ignition delay time decreases.
Journal of the Korean Society of Propulsion Engineers
/
v.8
no.3
/
pp.68-74
/
2004
Effect of fluctuation imposed on the inflow to LOX manifold of liquid rocket has been analyzed numerically. Time-varying fluctuation was idealized by the sinusoidal signal and three different representative frequencies were considered. It was found that all the frequencies tested produced the consistent flow reactions in the manifold in that the place close to the region of infection showed oscillatory flow rate through injector orifices in phase with the inflow fluctuation whereas the other side exhibits characteristics which are out of phase.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
v.y2005m4
/
pp.66-71
/
2005
In this study the regression rate of hybrid rocket fuel has been investigated by two methods. First method is to use swirl injectors for enhancement of regression rate. And second method is the modification of the helical grain deriving improvement of combustion area and generating swirl flow. Tests have been done with PMMA and gaseous oxygen. In this paper the incline angle of the helical grain was varied to find the optimal condition to obtain the max regression rate for a given operational condition.
Journal of Korean Society of Environmental Engineers
/
v.22
no.4
/
pp.651-659
/
2000
The characteristics of ammonia removal by natural neutralizer were studied by using a scrubber type equipment. As operation parameters, neutralizer dilution ratio, neutralizer inlet flowrate, air flowrate and initial ammonia concentration were selected and their effects on ammonia removal efficiency were investigated. The optimal removal effect was achieved at neutralizer dilution ratio of 1.0% and neutralizer inlet flowrate of $60m{\ell}/min$. On the other hand, with respect to air flowrate and initial ammonia concentration, there was no significant effect on removal efficiency, when loading rate was considered. In addition, ammonia removal reaction was investigated by analyzing the ammonia oxides, such as nitrites and nitrates, after reacting ammonium solution with natural neutralizer. The result shows a partial oxidation by natural neutralizer besides dominant absorption of ammonia.
The pressurant mass required for propellant tank pressurization with operating condition variation was estimated by using the numerical model already developed for this purpose. The model was applied to the concept design results of KSLV-II first stage oxygen tank. The supplied pressurant temperature, oxygen volumetric flow rate, and the ratio of length to diameter of the tank were selected as variables. The required pressurant mass and mass flow rate, collapse factor, ullage temperature distribution were predicted, and the results showed that the pressurant temperature had the largest effect on the amount of the required pressurant mass. The pressurizing efficiency of the propellant tank was calculated through analyzing energy distribution in the ullage. It was found that the gas-to-wall heat transfer in the ullage was dominant, and much of the pressurant energy was lost to tank wall heating.
Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
/
2000.11a
/
pp.138-138
/
2000
국내의 백상지 공정은 공정에 투입되는 청수의 양을 줄이면서 동시에 폐수 배출 양을 감 소시키기 위해 많은 노력을 하고 있다. 공정으로 유입되는 청수의 양과 처리된 폐수의 양을 줄이기 위한 방법으로 PDFCpolydisk filter)를 도입하여 백수를 여과하여 showertf sealing 에 재사용하고 있으며 공정수 재활용에 따른 유기 물질과 무기물질의 계 내로의 축적을 방 지하기 위한 효과적인 폐수 처리방법을 모색하고 있다. 일반적으로 청수를 백수로 대체할 경우 공정 백수 내에 TDSCtotal dissolved solid), T TSSCtotal suspended solid), CODCchemical oxygen demand), 전기 전도도와 칼숨 경 도 등이 증가되며 음이온성 저해 물질Canionic trash)이 증가하여 보류 및 지력증강용 첨가제의 효율 을 떨어뜨릴 뿐만 아니라 마모, 슬라엄, 펠트 막힘 등의 문제를 유발하게 된다고 알려져 있다. 청수를 백수로 대체함에 따라 생기는 이러한 문제를 해결하면서 효율적인 청수 절약 방안 을 세우기 위해서는 무엇보다도 문제를 유발하는 원인 물질의 축적 양을 예측하는 것이 중 요하다고 판단된다. 본 연구는 백상지 공정의 폐쇄화 수준이 높아짐에 따른 공정 백수 내의 유기물질의 축적 현상을 분석하는 것올 목적으로 하였다. 이를 위해 산화전분을 유기물질의 대표하는 물질로 설정하였다. 이는 백상파지와 함께 초지계 내로 유업되는 산화전분은 파지의 4%를 차지할 정도로 유입량이 많을 뿐만 아니라 음이온성을 띄고 있어서 지료에 홉착율이 낮고 양이온성 고분자의 효율을 저해하며 슬라임의 원인이 되기도 하는 물질이기 때문이다. 산화전분의 축적 현상을 분석하기 위하여 pilot 설비 상세 설계도를 참고하여 하루 생산량 이 16 T/D이고 백상파지만이 파지로 유입되는 백상지 생산 공정을 모델로하였으며, 산화전 분의 홉착과 용출 모델을 만들어 상용 시율레이터를 이용하여 시율레이션 프로그램을 작성 하였다. 시률레이션 프로그램에서는 장섬유 미세섬유, 충전제를 지료 구성 성분으로 설정하였고 O Orccotoma 등이 사용한 일과 보류도 모델을 응용하여 보류도 모델올 만들었다. 산화전분은 백상파지에 포함된 형태로만 초지계 내로 유입되며 백상파지가 해리되는 과정에서 완전히 백수에 용출되었다가 지료 구성 성분에 홉착되는 것으로 가정하였다. 지료 홉착된 산화전분 의 양은 용존 산화전분 총량에 비례하는 것으로 가정하였으며, 이 때 이 비례상수를 전분 홉착율이라 정의하였다. 시율레이션 결과, 공정 폐쇄화가 진행됨에 따라 백수 내의 산화 전분 농도는 증가하게 되 며, 폐쇄화 수준이 높아질수록 백수 내 전분 농도의 증가량은 더 높아졌다. 백수 내의 전분 농도의 증가량은 백상파지 첨가량이 증가할수록, 표면 사이징 양이 증가할수록 커졌다.
액체추진제를 사용하는 위성 발사체의 경우 추진제탱크에 저장된 추진제를 추력을 발생하는 연소실에 공급하기 위하여 헬륨 등의 가압제를 사용한다. 본 연구에서는 액체추진제 로켓엔진의 산화제인 극저온의 액체산소를 저장하고 있는 탱크 내부에 설치된 별도의 탱크에 저장된 극저온/고압의 헬륨을 고온으로 열팽창 시켜 추진제 탱크로 재유입하여 추진제를 가압하는 시스템에 사용되는 가압제 열팽창용 열교환기의 개발을 위한 기초 설계를 수행하였다. (중략)
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2008.11a
/
pp.261-264
/
2008
This study experimentally examines combustion characteristics of a hybrid rocket in which solid paraffin is used as a fuel, while oxidizer is pure oxygen. Especially, the experiment investigates the effects of chamber pressure and configuration of fuel grain. The pressure inside the combustion chamber is varied by changing a flow rate of oxidizer. The regression rate is observed to increase as the chamber pressure does. There also exists the effects of shape of fuel grain on thrust. Characteristic of paraffin hybrid rocket changes with shape of fuel grain. When there is a room near the injector, thrust increases. On the other hand, the room near the nozzle does not contribute to thrust increasement.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2017.05a
/
pp.1084-1087
/
2017
When a liquid rocket engine is started the oxidizer and fuel must be flowed into combustion chamber and gas generator with time differences. The wrong time difference between propellants or malfunction of ignition device can occur the explosion of combustion chamber due to detonation by energized premixed-propellants. Therefore it is important to observe the transient characteristic of propellants or to measure the inflow time of propellants into combustion chamber and gas generator. The measurement of static pressure is not enough to observe the propellants inflow time into combustion chamber and gas generator. By measuring dynamic pressure of main flow passage of propellants the accurate propellants inflow time could be investigated.
Smoldering is a non-flaming combustion mode, characterized by thermal degradation and c charring of the virgin material, evolution of smoke and emission of visible glow. A big fire may @ occur even in a confined environment having a limited amount of oxygen, due to smoldering c combustion through a porous solid material. This paper presents a theoretical analysis on the effect of smoldering combustion on fire occurrence based on a report about fire investigation of a real f fire accident. It is assumed that the propagation of the smolder wave is one-dimensional, d downward, opposing an upward forced flow and steady in a frame of reference moving with the s smolder wave. Smoldering combustion is modeled by a one-step reaction mechanism, without c considering pyrolysis. It is found that dominant parameters controlling smoldering combustion i include mass flux of oxidizer entering the reaction zone and void fraction of solid fuel. It is also found that the mechanism of transition to flaming is critically influenced by these two parameters.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.