• Journal of the Korean Electrochemical Society
• /
• v.10 no.3
• /
• pp.207-212
• /
• 2007

[ $PSCF3737(Pr_{0.3}Sr_{0.7}Co_{0.3}Fe_{0.7}O_3)$ ] is a good candidate cathode material for IT-SOFC(intermediate temperature solid oxide fuel cell) because of high MIEC(mixed ionic electronic conductor) conductivity. In this study, the characteristics of PSCF3737 was investigated and optimizations of sintering temperature and thickness for $PSCF3737(Pr_{0.3}Sr_{0.7}Co_{0.3}Fe_{0.7}O_3)$ was carried out. Impedance responses were divided into two parts by frequency region. Middle frequency part (${\sim}10^2\;Hz$) was concerned with oxygen reduction reaction on surface and low frequency part (${\sim}10^{-1}\;Hz$) was related with oxygen diffusion. The reasonable sintering temperature and thickness of cathode were $1200^{\circ}C$ and about $27\;{\mu}m$ with regard to EIS(electrochemical impedance spectroscopy). ASR(areas specific resistance) of optimized cathode is $0.115\;{\Omega}\;cm^2$ at $700^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.2
• /
• pp.148-155
• /
• 2015

Electrospun $LaCoO_3$ perovskite nanofibers were produced for the air electrode in Zn-air rechargeable batteries using electrospinning technique with sequential calcination. The final calcination temperature was varied from 500 to $800^{\circ}C$ in order to determine its effect on the physical and electrochemical properties of the prepared $LaCoO_3$ perovskite nanofibers. The surface area of the electrospun $LaCoO_3$ perovskite nanofibers were observed to decrease with increasing final calcination temperature. Electrospun $LaCoO_3$ perovskite nanofibers calcined with final calcination temperature of $700^{\circ}C$ had the best electrocatalytic activity among the prepared perovskite nanofibers.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.1
• /
• pp.11-25
• /
• 2009

Fuel cells are expected to be one of the major clean new energy sources in the near future. However, the slow kinetics of electrocatalytic hydrogen oxidation reaction (HOR) and oxygen reduction reaction (ORR), and the high loading of Pt for the anode and cathode material are the urgent issues to be addressed since they determine the efficiency and the cost of this energy source. In this review paper, a new approach was developed for designing electrocatalysts for the HOR and ORR in fuel cells. It was found that the electronic properties of Pt could be fine-tuned by the electronic and geometric effects introduced by the substrate alloy metal and the lateral effects of the neighboring metal atoms. The role of substrate was found reflected in a volcano plot for the HOR and ORR as a function of their calculated d-band centers. This paper demonstrated a viable way to designing the electrocatalysts which could successfully alleviate two issue facing the commercializing of the fuel cell-the cost of electrocatalysts and their efficiency.

• Clean Technology
• /
• v.14 no.1
• /
• pp.61-68
• /
• 2008

There have been great attentions on polymer electrolyte membrane fuel cell (PEMFC) due to their advantageous characteristics such as zero emission of hazardous pollutant and high energy density. In this work, we evaluated degradation phenomena and stability of single cell performance via one dimensional single cell modeling. Here, CO poisoning on anode on anode was considered for cell performance degradation. Modeling results showed that the performance and stability were highly degraded with CO concentration in fuel gas. In addition, cell performance was reduced by slow oxygen reduction on cathode in long term operation. In order to overcome, it is required to increase ratio o#hydrogen in the fuel gas of anode and high Pt loading contained in the cathodic catalyst layer.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.2
• /
• pp.186-192
• /
• 2013

In order to reduce the costs and to improve the durability of solid oxide fuel cell (SOFC), the operating temperature should be decreased while the power density is maintained as much as possible. However, lowering the operating temperature increases the cathode interfacial polarization resistances dramatically, limiting the performance of low-temperature SOFC at especially purely electronic conducting cathode. To improve cathode performance at low temperature, the number of reaction sites for the oxygen reduction should be increased by using a mixed ionic and electronic conducting (MIEC) material. In this study, anode-supported fuel cells with two different thicknesses of the MIEC cathode were fabricated and tested at various operating temperatures. The anode supported cell with $32.5{\mu}m$-thick BSCFZn-LSCF cathode layer showed much lower polarization resistance than that with $3.2{\mu}m$ thick cahtode and higher power density especially at low temperature. The effects of cathode layer thickness on the electrochemical performance are discussed with analysis of impedance spectra.

• Journal of the Korean Electrochemical Society
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2014

This review article summarizes photoelectrochemical water splitting using gallium nitride (GaN). GaN materials have been studied as novel photoelectrode material due to its chemical stability and easy band gap engineering. Unlike other semiconductor materials that are easily corroded in strongly acidic or alkaline electrolyte, n-type GaN is chemically stable enough to be used as photoanode in oxygen evolution reaction. Furthermore, studies on p-type GaN have been recently reported. This review briefly discusses problems that need to be solved before GaN materials find widespread use in solar fuel application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.676-676
• /
• 2013

무기물 양자점을 광감응 염료로 사용하는 경우 양자점의 사이즈 조절만으로 밴드갭을 조절할 수 있어 광학적 특성 조절이 용이하며, 유기 염료보다 광흡수 능력이 뛰어난 장점을 가진다. 특히 카드뮴 계열의 CdS, CdSe 양자점을 순차적으로 증착하여 사용하는 경우 가시광 전 영역을 효율적으로 흡수, 이용할 수 있어 광전기화학 셀의 광전극으로 사용 시 높은 성능을 기대할 수 있다. 하지만, 카드뮴 계열 양자점의 경우 광전기화학 셀로의 구동에 있어 안정성이 낮은 문제점이 있으며, 이는 양자점에 남아있는 정공이 관여하는 양자점 부식 반응으로 인한 것이다. 본 연구에서는 보다 안정적이면서도 고효율의 광전기화학적 수소생산 시스템을 위해, CdSe/CdS 양자점 감응형 ZnO 나노선 광전극에 IrO2 촉매물질을 증착하였다. CdSe/CdS 양자점이 가시광 전 영역을 흡수하며, ZnO 나노선 구조를 통해 생성된 광전자를 효율적으로 포집하여 높은 광전류 특성을 기대할 수 있다. 나아가 산소생산용 조촉매로 많이 사용하는 $IrO_2$ 촉매 물질의 추가증착을 통해 양자점에서 생긴 정공을 빼 줌으로서 정공이 관여하는 양자점 부식 반응을 방지할 수 있다. 실험결과 촉매물질의 증착 이후 광전류 생성 특성 및 수소생산량이 증가하였으며, 안정성 또한 상당히 향상된 것을 확인할 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.97.1-97.1
• /
• 2011

저온에서 양이온 고분자막을 사용하는 고분자 연료전지의 경우 뛰어난 성능과 다양한 응용분야로 인해 많은 연구와 실증이 이루어지고 있지만 공기극에서의 느린 산소 환원반응으로 인해 백금과 같은 귀금속의 사용이 불가피하고 백금의 제한된 매장량과 높은 가격으로 인해 상용화가 늦어지고 있다. 그래서 많은 연구자들이 합금 촉매 또는 비귀금속 촉매를 이용한 전극 개발에 집중하고 있다. 알칼리 분위기에서 저가의 전이 금속들이 백금과 비슷한 활성을 보이고 고체 음이온 교환막이 개발됨에 따라 최근 알칼리 연료전지가 다시금 큰 주목을 받고 있다. 그러나 고분자 연료전지와는 달리 아직 촉매나 전해질막, 이오노머의 특성 및 메커니즘에 관해 별로 알려진 것이 없다. 본 연구에서는 직접 개발한 세공충진막 형태의 탄화수소계의 음이온 교환막과 비귀금속 공기극 촉매를 이용하여 막전극접합체(MEA)를 개발하였고 촉매 및 이오노머 함량과 같은 전극 조성, 막전극접합체의 제조 및 체결, 가습이나 가스조성 등의 단위전지 운전조건과 같은 다양한 변수에 대해에 최적 조건을 도출하고자 하였다. 공기극 촉매는 Cu-Fe/C를 이용한 상용 촉매를 이용하였고 이오노머의 경우는 탄화수소계의 상용 제품을 사용하였으며 음이온 교환막에 전극층을 형성하기 위해서는 스프레이 공정을 이용하였다. 단위전지를 통해 성능을 확인하였고 임피던스 및 CV를 통해 전기화학적인 특성을 규명하였다. 조건의 최적화를 통해 상당한 성능 향상을 이루었으나 추가적인 성능 향상 및 내구성 확보 등에 대해 계속적인 실험을 진행할 예정이다.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1051-1053
• /
• 1995

Nowadays perovskite $La_{1-x}Sr_xMnO_3$ is preferred cathode material in Solid Oxide Fuel cell(SOFC). The $La_{1-x}Sr_xMnO_3$ with Sr contents ranging $x=0{\sim}1.0$ were prepared by a citrate method. These powders were characterized by usual means like TG/DTA, X-ray diffraction analysis. The samples used for measuring thermal expansion were prepared as pellets by cold pressing and subsequent sintering in air at $1200^{\circ}C$ for 5 hours. To measure the by-product of $La_{1-x}Sr_xMnO_3$ reacted with 8mol% YSZ, that samples were sintered at $1200^{\circ}C$ for 5 hours.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.104-108
• /
• 2000

It is very important to know the real roughness of electrode surface in electrochemistry. But it is impossible to know absolute roughness of electrode surface for various reasons. In this work, we compared the roughnesses of polycrystalline gold electrode often used in electrochemistry calculated from the images of scanning tunneling microscopy (STM) and cyclic voltammetry with those of Au (111) and HOPG. The roughness of polycrystalline gold calculated from STM image was $1.1(\pm0.1)$, that from adsorption-desorption of oxygen was $2.4(\pm0.7)$ and that from adsorption of N-docosyl-N'-methyl viologen was $1.6(\pm0.1)$.