• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.11
• /
• pp.1104-1111
• /
• 2008

The supersonic advanced trainer based on digital flight-by-wire flight control system uses aircraft flight information such as altitude, calibrated airspeed and angle of attack to calculate flight control law, and this information is measured by IMFP(Integrated Multi-Function Probe) equipment. The information has triplex structure using three IMFP sensors. Final value of informations is selected by mid-value selection logic to have more flight data reliability. As the result of supersonic flight test, pitch oscillation is occurred due to IMFP noise when altitude hold autopilot mode is engaged. This tendency may affect stability and handling quality of an aircraft during autopilot mode. This paper addresses autopilot control law design to remove pitch oscillation and these control laws are verified by non-real time simulation and flight test. Also, pitch response characteristics of pitch attitude hold autopilot mode is improved by upgrading the control law structure and feedback gain tuning during bank turn.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.66-72
• /
• 2007

an approach to air-vehicle design, an application of the radio-controlled model flight test techniques has been presented. The approach presented in this study is to validate the air-vehicle design configuration by analyzing the flight test results of scale model with dynamic similarities, and then to apply the analyzed results to the aerodynamic design process in early stage of the air-vehicle development. To develop practically applicable similarity laws for the subscale flying model design, the air-vehicle motions are decoupled into rotational motions for stability & control similarities and translational motions for flight performance similarities. Also, detail techniques for radio-controlled model flight test have been developed. Based on the results obtained from the radio-controlled flight test, the present approach for air-vehicle design has shown to be useful to validate the air-vehicle design configuration.

• Aerospace Industry
• /
• s.104
• /
• pp.16-19
• /
• 2009

지난 8월 1일 "군용항공기 비행안전성 인증에 관한 법률"이 본격 시행됐다. 국제적 수준의 비행안전 인증 체계를 마련함으로써 이제 우리도 우리 손으로 만든 국산 군용항공기의 비행안전성을 체계적으로 검증하고 국가가 그 성능을 보증할 수 있게 된 것이다. 뿐만 아니라 감항인증 관련 비용 및 시간을 대폭 단축할 수 있어 우리 손으로 만든 KT-1과 T-50의 해외 수출에도 큰 도움이 될 것으로 전망되고 있다. 군용항공기 감항인증제도 시행과 관련하여 현재까지의 진행경과 및 감항인증제도 도입 의의를 정리했다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.349-357
• /
• 2022

Since the flight control computer of unmanned aerial vehicle (UAV) is a flight critical equipment, it is necessary to ensure reliability and safety from the development step, and a redundancy-based fault management design is required in order to operate normally even a failure occurs. To reduce cost, weight and power consumption, the dual-redundant flight control system design is considered in UAV. However, there are various restrictions on the fault management design. In this paper, we propose the fault detection and isolation designs for the dual-redundant flight control computer to satisfy the safety requirements of an UAV. In addition, the flight control computer developed by applying the fault management design performed functional tests in the integrated test environment, and after performing FMET in the HILS, its reliability was verified through flight tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.9
• /
• pp.859-866
• /
• 2008

A guidance scheme for controlling the relative geometry of multiple flight vehicle formation flying is proposed. Each flight vehicle in the formation takes the roles of leader and follower simultaneously except for the formation leader. In this scheme, the flight commands for a leader are shared by all the followers and this leaders to a synchronized flight of all flight vehicles comprising the formation. Lyapunov stability theorem is used to obtain the guidance law. High fidelity nonlinear simulation results are presented to show the effectiveness of the proposed guidance law using a reconnaissance and surveillance mission example.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.169-179
• /
• 2010

Satisfying the same probability of loss of control and essentially two fail operative performance with a triplex computer architecture requires a lot of modification of the conventional redundancy management design techniques, previously employed in quadruplex digital flight control computer. T-50 FCS for triplex redundancy management design applied an advanced digital flight control architecture with an I/O controller which is functionally independent of the digital computer to achieve the same reliability and special failure analysis and isolation schemes for fail operational goals with a triplex configuration. The analysis results indicated that the triplex flight control system is to satisfy the safety requirement utilizing the advanced flight control techniques and the system performance of the implemented flight control system was verified by failure mode effect test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.11
• /
• pp.33-40
• /
• 2005

The reliability of flight control system(FCS) for Unmanned Air Vehicle(UAV) is underestimated because of the design restrictions such as small size, low cost and light weight. However because the failure of FCS may cause the loss of aircraft, the reliability of FCS must be analysed and validated whether it meet the reliability requirements in design phase.In this paper the failure rate of subsystems was divided with its function based on the design experience of FCS. The redundancy models which satisfy the system reliability requirements were suggested. These results may be utilized in the hardware design of FCS.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.8
• /
• pp.813-822
• /
• 2010

Integrated data processing for display of flight critical data and mission critical data was conducted without additional display instruments using glass cockpit design. Based on a pre-designed flight critical system and a mission critical system, this paper shows an optimal design of subsystem integration. The design satisfies safety requirements of flight control systems(FCS) and requires minimized modification of pre-designed systems. By conducting integration test using System Integration laboratory(SIL), it is confirmed that the introduced design approach meets the safety requirements of the MEP system.

• Journal of Internet Computing and Services
• /
• v.15 no.1
• /
• pp.1-17
• /
• 2014

Flight software operated on the on-board computers in the satellite has requirements such as real-time, high reliability. These requirements make dependency between the flight software and operating environments. Further, whenever a new system is built, such problem drives that all flight software are redeveloped. Thus, the dependency problem between them should be solved. And the problem can be resolved by improving the portability of the flight software. In order to improve the portability it is required to minimize the porting cost. In this paper, we classify the portability with the portability achieving methods. Using the classified portability, we propose a platform architecture that is based on the IMA concept and provides various portability capabilities. The proposed architecture enables us to solve the problem about the development of the flight software.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.3
• /
• pp.93-100
• /
• 2006

Modern versions of supersonic jet fighter aircraft using a digital flight-by-wire flight control system design utilizes a control surface reconfiguration in order to guarantee the aircraft flight stability when a control surface is failed. The T-50 flight control laws are designed such that the surface reconfiguration mode controls the aircraft using non-failed control surfaces when one of the control surfaces is failed. In this paper, linear analysis and HQS(Handling Quality Simulator) pilot simulations are performed to analyze the flight stability and handling quality when the surface reconfiguration mode is engaged for aircraft landing configuration. It is found that the aircraft flight stability and handling quality is satisfied to level 1 requirements when the T-50 flight control law is changed to the surface reconfiguration mode.