• Journal of Korean Port Research
• /
• v.10 no.1
• /
• pp.37-51
• /
• 1996

2차의 섭동법과 경계요소법에 기초한 시간영역해석법은 불규칙파의 파동장에 있어서 파-구조물의 비선형간섭을 해석할 수 있는 해석법이지만. 파와 구조물의 운동이 정상상태에 도달하기까지 시간스텝으로 계산을 수행하여야 하므로 계산시간이 매우 길어지고, 각 성분파와 그에 의한 운동요소를 평가하는 것이 어렵다. 반면에 주파수영역해석법은 계산시간이 짧고, 각 성분요소들의 변화특성을 쉽게 판단할 수 있지만, 불규칙파동장으로의 적용이 현실적으로 어렵다는 단점을 가진다. 본 연구에서는 잠제 등에 대해서 전개되어 있는 주파수영역해석법을 임의형상의 부체 구조물에 대해 새롭게 수식의 전개를 수행하고, 압축공기주입 부체구조물에 적용하여 실험 및 이론해석결과로부터 그의 타당성을 확인한다. 이 때 압축공기의 거동은 Boyle법칙을 사용하여 평가한다.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.59-70
• /
• 1992

A Finite volume method for the computation of the two-dimensional, incompressible, steady, laminar Navier-Stokes equation is developed using a non-staggered grid system in a general curvilinear coordinate. The numerical pressure fluctuations, usually encountered when the non-staggered grid system is used, is suppressed by the momentum interpolation method. Flows around a NACA0012 foil section have been computed by the present method and the results show good agreements with other experimental and numerical ones.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.441-446
• /
• 2006

유역에서 발생한 고탁수가 저수지내에서 장기화하는 현상에 관한 대책은 장기간이 소요되는 유역관리 대책과 탁수저감일수를 최소화하는 선택취수 개념의 우선 방류기법 등이 있다. 하류하천으로의 탁수 우선배제를 실시하기 위해서는 댐 방류탁수가 하류에 미치는 영향을 정확히 예측할 수 있는 하천탁도 예측 및 관리시스템 구축이 필요하다. 최근 고탁수현상을 경험한 낙동강 수계에서는 본류의 탁도 관리를 위해 임하댐 및 안동댐의 연직 탁도 분포 변화에 따라 댐 방류탁수에 의한 영향을 최소 또는 기준치 이하로 할 수 있는 댐 연계운영에 관한 조건 도출이 필요하다. 선택취수에 관한 수치모의 결과를 이용하여 저수지내 온도 및 탁도 분포 변화와 취수탑의 수문운영에 따른 방류수의 온도 및 탁도를 예측할 수 있다. 본 연구에서는 이와 같은 결과를 이용하여 안동댐과 임하댐의 방류조건에 대한 하류하천 합류부에서의 2차원 이송 확산 수치모의를 수행하고자 하였다. 이와 같은 연구를 성공적으로 수행하기 위해서는 지속적인 현장조사를 통한 지점별 탁도-SS 상관관계 도출, 비정상 흐름 및 수질모의 검 보정, 탁도예측 결과 검증이 필요하다. 평면 2차원 흐름 및 수질 모의 결과에 의하면, 임하댐 방류 탁도로 인한 반변천의 고탁수는 안동댐 방류 수에 지배를 받는 낙동강 본류와 합류되는 지점에서부터 약 5 km 떨어진 지점에서 횡방향 완전혼합이 이루어지는 것으로 나타났다. 이와 같은 모의결과는 완전혼합을 가정하는 1차원 수질모델링의 초기 입력자료에 사용됨으로써 1차원 탁도 모의결과의 정확성을 높이는 데 사용될 수 있다. 이를 이용하여 낙동강 수계 댐 연계운영에 따른 낙동강 탁도 예측모의를 수행하고, 이 결과를 이용하여 낙동강 탁도 예경보 시스템을 구축해야 할 것이다. 또한 선택취수 등을 통해 저수지 관리를 효과적으로 수행하기 위해서는 저수지 내부의 탁도 거동을 정확히 예측할 수 있어야 한다. 따라서 추후 동수역학 및 열역학에 기초한 3차원 수치모형 연구와 성층흐름에 정밀한 밀도류 실험연구 및 이에 대한 적용이 필요할 것으로 판단된다.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.316-325
• /
• 2002

The deformation and coalescence behaviors of immiscible LDPE/PS blends (86.5/13.5 vol%) prepared by internal mixer were studied using rheometer and scanning electron microscope. The fine droplets coagulated at initial stage of mixing, and deformed fiber at large strain. The critical capillary number was calculated according to the empirical equation of De Bruijn and it was 0.95, the local capillary number was 3.867. The polymer blends were annealed at $200^{\circ}C$ for various time to investigate morphological change of polymer blends. The maximum size of droplet after annealing at $200^{\circ}C$ was found at ${\gamma}$=1798, and there was destruction of the morphology at 15 minutes of annealing time. The viscosity of matrix was critical to determine a coalescence of droplet.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.15-22
• /
• 2010

A series of field pull-out tests were carried out to investigate the behaviour of multi-pressurized soil nails. Ten soil nails were constructed in weathered soil and then, subjected to pull-out loads. The test results showed that the ultimate pull-out resistances of soil nails constructed with high pressure were about 42~142% larger than those obtained from conventional soil nails. The deduced interface shear strength at the ground-grout interface was 71 kPa for conventional soil nails, while higher shear strength of 95~166 kPa was obtained for pressurized nails. The diameter of grouted borehole increased by about 12~27% compared to ordinary soil nails under low pressure. Also, the predicted value by the cavity expansion theory is in good agreement with the measured expanded radius of grout under injection pressure by field pull-out tests.

• Composites Research
• /
• v.19 no.1
• /
• pp.22-28
• /
• 2006

In manufacturing process of composite cylinders with metal liner, the autofrettage process which induces compressive residual stress on the liner to improve cycling life can be applied. In this study, a finite element analysis technique is presented, which can predict accurately the compressive residual stress on the liner induced by autofrettage and stress behavior after. Material and geometrical non-linearity is considered in the finite element analysis, and the Von-Mises stress of a liner is introduced as a key parameter that determines pressure cycling life of composite cylinders. Presented methodology is verified through fatigue test of liner material and pressure cycling test of composite cylinders.

• Journal of Energy Engineering
• /
• v.20 no.1
• /
• pp.1-7
• /
• 2011

The performance and life-cycle costs of electric vehicle(EV) and hybrid electric vehicle(HEV) depend inherently on battery packs. Temperature uniformity in a pack is an important factor for obtaining optimum performance for an EV or HEV battery pack, because uneven temperature distribution in a pack leads to electrically unbalanced battery cells and reduced pack performance. In this work, a three-dimensional modeling was carried out to investigate the effects of operating conditions on the thermal behavior of a lithium-ion battery pack for an EV or HEV application. Thermal conductivities of various compartments of the battery were estimated based on the equivalent network of parallel/series thermal resistances of battery components. Heat generation rate in a cell was calculated using the modeling results of the potential and current density distributions of a battery cell.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.295-301
• /
• 2009

In general the stability of soil nail-slope system, the shear resistance is neglected because the tensile resistance of nail acts mainly for slope stabilization. This is because that deformed steel is generally used for nail and it does ductile behavior. In other side when the steel pipe with high rigidity is used for nail, the shear resistance at failure surface work more than deformed steel. In order to analyze effects of shear resistance at the soil nail-slope system with high steel piped nail, a series of numerical analyses were performed. Also numerical analyses at 3 conditions - 5 nailed, 7 nailed, 9 nailed at the same slope were perfomed for investigating the trend of shear resistance effect. From these 3D numerical analyses, it was found that the maximum shear resistances at each nails were larger in case of steel piped nail and because of this, the factor of safety at the condition of the steel piped nail appears larger than that of deformed steel nail.

• Journal of the Korean Ceramic Society
• /
• v.34 no.3
• /
• pp.289-295
• /
• 1997

Effect of ceramic processing was investigated on the microstructure and electronic properties of low loss Mn-Zn ferrite. Addition of CaO and SiO2 to calcined powder rather than to raw materials mixtured resulted in finer-grained microstructure. Higher oxygen pressure during sintering caused microstructural inhomogeneity and the increase in power loss and disaccommodation factor. Relatively low power loss was found for sintering up to 130$0^{\circ}C$ from powders calcined at high temperature and milled shortly. It was caused by slow densification rate and normal grain growth up to 130$0^{\circ}C$. Calcination at low temperature and prolonged milling enhanced den-sification, which gave a fine grained microstructure and low powder loss at sintering temperture below 120$0^{\circ}C$. Sintering temperature above 125$0^{\circ}C$, however, showed abnormal grain growth.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.2
• /
• pp.47-54
• /
• 2008

In this paper, we studied how and why did abnormal IMC growth at component affect on board level mechanical reliability. First, interfacial reactions between Sn2.5Ag0.5Cu solder and electrolytic Ni/Au UBM of component side were investigated with reflow times and thermal aging time. Also, to compare mechanical reliability of component level, shear energy was evaluated using the ball shear test conducted with variation of shear tip speed. Finally, to evaluate mechanical reliability of board level, we surface-mounted component fabricated with each condition on PCB side. After conducting of 3 point bending test and impact test, we confirmed solder joint crack mode using cross-sectioning and dye & pry penetration method.