• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.4
• /
• pp.98-107
• /
• 1996

In order to predict analytically torque, thrust force, tool life and chip formation in drilling, cutting models for chisel edge with various tool-chip contact length were developed in this type. Also, the experimental tests are run with various pilot holes. The following conclusions were obtained from the analysis. \circled1 It's also found experimentally that thrust force(Fz) decreases as pilot hole diameter increases. \circled2 Surface roughness for material(G) is larger that for material(J). The difference over two materials in roughness value about 0.5$mu extrm{m}$. \circled3 Flank wear of the drill in cutting material of G less than any other kinds of materials(F, G, H, I, J). \circled4 In drilling a deep hole on a workpiece over SM45C either twist drill. The chip was conical helix type at the fist suspensely change the two segment type and than two a long pitch helix style.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3899-3908
• /
• 1996

In order to clarify the effects of nonmetallic inclusion contents insteels (SM45C & SCM440) on the tool life, cutting experiment was performed under various cutting conditions. Tool life, cutting force, roughness of machined surface and cutting mechanism are examined on these two kinds of steel. The following conclusions were obtained from the analysis (1) Cutting force of the steels was not affected by chemical component and nonmetallic inclusion. (2) If the rate of amount, Ca/S has a value grater than about 0.2 and addition of less amount of Al, Mn, tool wear of tips decreasesinturning. (3) It is also proved that higher contents of nonmetallic inclusion improve roughness of the surface. (4) Less amount of Ca, higher amount of S, Mn and Al improve the chip breakability.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.1119-1129
• /
• 2011

Shot-peening effects on the fatigue behavior of bearing steel were investigated under the high cyclic loading. Hourglass shape specimens were made of bearing steel(JIS-SUJ2) for rotary bending fatigue tests. Two kinds of treatments were performed : a heat treatment and a shot-peened surface treatment after the heat treatment. The fracture surfaces of specimens were classified into two types of fracture mode : the surface fracture mode induced by a surface defect and the internal fracture mode induced by a nonmetallic inclusion. Inclusion depth and shape affected considerably the fatigue life. Shot-peening treatment improved much the fatigue life of the bearing steel under low and high levels of cyclic loads. Probabilistic-stress-life (P-S-N) curves were suggested for the reliable fatigue life estimation of the improved bearing steel.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.3
• /
• pp.240-251
• /
• 2019

This study examined the manufacturing technology used for the flat iron axes excavated from Ulsan Hadae. Their microstructures were analyzed using metallurgical methods. In addition, a variety of manufacturing technologies were examined and compared using existing research materials on flat iron axes. As a result of analyzing ten flat iron axes, which were excavated in the order that they were laid out in a row in one of the wooden coffin tombs at Ulsan Hadae, Tomb No. 44, it was possible to classify the flat iron axe manufacturing technology and system into three types: 'pure iron - shape processing', 'pure iron - shape processing - carburizing', and 'pure iron - shape processing - carburizing - decarburizing.' All of the flat iron axes were produced by forging, and most of them were made by beating the pure iron into their shapes. In particular, a number of the flat iron axes were reinforced through a carburizing process after shaping the iron. This appears as steel products forming the basis of the steel industry at the time were commonly used as an intermediary material or currency. On the other hand, it was commonly found in all samples that the hardening was not performed after shaping or carburizing. Since the microstructure of the flat iron axes made of pure iron contained a large number of impure inclusions and the result of analyzing the components of the non-metal inclusions showed characteristics of slag which contains a mixture of glass phase and wustite, it is possible that low-temperature reduction was used in the refining process.

• Journal of Welding and Joining
• /
• v.7 no.2
• /
• pp.49-59
• /
• 1989

The effect of non-metallic inclusions on the HAZ hydrogen induced cracking was investigated. Quench and temper high tensile strength steels containing various sulphur contents were employed. The sulphur contents range between 0.007% and 0.040%. Non-metallic inclusions were mainly MnS type sylphide and Mn-Al-Si type. The sensitivity of HAZ delayed cracking was evaluated by implant testing. Diffusible hydrogen content was varied by controlling the moisture absorbing condition of manual arc welding electrodes. The one was asreceived condition, the other was dipping the electrodes in the water for ten minutes. The main results obtained were as follows; 1) The results of implant test showed that critical stress increased with increasing S content up to 0.013%. But steel containing 0.040%S showed lower critical stress than that of 0.013% S. These result suggest that there will be optimum S content to prevent HAZ delayed cracking of high strength steels. 2) Under the lower D.H.C. level, critical stress was increased with rolling reduction, but higher D.H.C. level, effect of rolling reduction was not recognized.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.47-47
• /
• 2009

용착금속의 미세조직은 크게 Acicular ferrite(AF), Ferrite with aligned second phase(FS), Primary ferrite(=Grain boundary Ferrite) 등으로 나눌 수 있다. 이 중 침상형 페라이트(AF)는 인성과 강도를 동시에 증가시킬 수 있으므로 이를 다량 확보하는 것이 용접산업의 관건이다. 본 연구에서는 침상형 페라이트 발생에 기여한다고 알려진 Ti 함량을 용착금속에서 단계적으로 조절하여 나타나는 미세조직과 특성변화를 관찰하였다. 모재는 HSB-600을 사용하였으며 용접재료는 ER100S-G급의 Ti가 함유되어 있는 것(A)과 미함유된 것(B)을 사용하였다. 모재 성분의 희석을 방지하기 위해 V-Groove 가공 후 Buttering 용접을 실시하였다. 중앙에 가공된 V-그루브에 이들 재료를 적절히 조합하고 용접(입열량 20kJ/cm)하여 Ti함유량을 총 4가지(0.002~0.025% Ti)로 제어하였다. 용접 후 각각의 시편에 대해 미세조직, 충격시험, O/N분석, 성분분석 등의 시험을 진행하였다. 미세조직 관찰결과 Ti함량이 증가할수록 AF는 증가하고 FS는 감소함을 확인할 수 있었으며 충격시험결과 Ti가 많이 함유된 시편일수록 더 낮은 연성취성 천이온도(DBTT)를 나타내었다. EDS와 SEM으로 관찰한 결과 Ti함량 증가에 따라 비금속개재물의 크기는 작아지고 밀도는 높아지는 것을 확인할 수 있었으며 개재물 내에서의 Ti함량도 더 많아지는 것을 확인 할 수 있었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.17 no.2
• /
• pp.89-99
• /
• 1997

Although discontinuously reinforced metal matrix composite(MMC) is one of the most promising materials for applications of aerospace, automotive industries, the thermal residual stresses developed in the MMC due to the mismatch in coefficients of thermal expansion between the matrix and the fiber under a temperature change has been pointed out as one of the serious problem in practical applications. There are very limited nondestructive techniques to measure the residual stress of composite materials. However, many difficulties have been reported in their applications. Therefore it is important to establish analytical model to evaluate the thermal residual stress of MMC for practical engineering application. In this study, an elastic model is developed to predict the average thermal residual stresses in the matrix and fiber of a misoriented short fiber composite. The thermal residual stresses are induced by the mismatch in the coefficient of the thermal expansion of the matrix and fiber when the composite is subjected to a uniform temperature change. The model considers two-dimensional in-plane fiber misorientation. The analytical formulation of the model is based on Eshelby's equivalent inclusion method and is unique in that it is able to account for interactions among fibers. This model is more general than past models to investigate the effect of parameters which might influence thermal residual stress in composites. The present model is to investigate the effects of fiber volume fraction, distribution type, distribution cut-off angle, and aspect ratio on thermal residual stress for in-plane fiber misorientation. Fiber volume fraction, aspect ratio, and distribution cut-off angle are shown to have more significant effects on the magnitude of the thermal residual stresses than fiber distribution type for in-plane misorientation.

• Conservation Science in Museum
• /
• v.24
• /
• pp.17-36
• /
• 2020

This paper describes the consevation treatment of eleven bigyeokjincheolloe bomb shells that were excavated from the Joseon-period local government office and fortress of Mujang-hyeon (present-day Mujang-myeon) in Gochang in 2018. It also provides information on the production method of the shells revealed through CT scanning, gamma-ray transmission imaging, and metallographic analysis. In preparation for the special exhibition "Bigyeokjincheolloe" at the Jinju National Museum in 2019 (July 16 to August 25), contaminants were removed from the shells and their surface was reinforced during the first phase of conservation treatment. Furthermore, the closures for the shells were identified for the first time. Regarding the production of the shells, the CT scanning and gamma-ray transmission imaging identified many blowholes in the interior of the body and the use of a chaplet on the side of one shell. The side of the body proved to be relatively thinner than the top and bottom. The traces of a hole for pouring molten metal into the center of the bottom indicates that molten metal was indeed emptied into the inverted body. In the metallographic analysis of two of the bodies and one lid, cementite and pearlite structures were identified on the body, indicating that it was made by casting. The presence of the ferrite structure with a partial distribution of the pearlite along with non-metallic inclusion in the lid suggested that the lid was made by forging.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.367-376
• /
• 2012

The ironware production technology is a measure to fathom the society's level of development in time. To understand iron-manufacure methods in the past, various investigations on the fine structures and additions of ironware remains and Iron ingot have been conducted in a way of natural science. This study metallurgically reclassifies remains excavated in iron-manufacture remains located in Beokje, Goyang, which are thought to be in time of Goryeo Dynasty, and draws an inference from the element analysis on the iron-manufacture and smelting technology. Iron ingot samples with a cast iron structure are divided into those with a white cast iron structure and those with a grey cast iron rich in P. The P content of grey cast iron appeared to be the result of adding a flux agent like lime, iron ingot and carbon steel iron ingot with a cast iron structure excavated in the area is regarded as pig iron which was made without a refining process. In this study it seems that two methods of making ironware were used in the area; one is the method of making ironware by pouring cast iron to the casting, and the other is the method of making carbon steel through the refinement of pig iron. It appears that highly even steel structure of carbon steel and a small amount of MnS inclusion are very similar with that of the modern steel to which Mn is artificially added. Nevertheless, these data alone cannot be used to determine the source of Mn in the carbon steel of the excavated from the iron-manufacture remains, which raises the need for further studies on the source and the possibility of carbon steel via the iron-manufacture process of cast iron.

• Journal of Welding and Joining
• /
• v.6 no.4
• /
• pp.44-53
• /
• 1988

The mechanical strengths of buried lamellar tears located near the weld toe in the welded tee joints were evaluated in terms of the loss of load carrying capacity as a function of tear area. In static loading, the load carrying capacity was significantly reduced when tear intercepted over 10% of the cross-sectional area of the welded joints. However, the welded joints containing buried tears still failed at stresses over the yield strength of the base metal in the through-thickness direction in spite of the presence of tears up to 20-25% of the area. Fatigue strength of welded joints containing tears markedly reduced with increasing tear areas. Lehigh lamellar tearing test used in this study to produce speicmens was described in detail. The load carrying cpapacity in static loading was influenced by the reduction of supporting area whereas that in fatigue loading was influenced by the stress-concentration effects of lamellar tears and the reduction of supporting area. In bend tests, the pre-existing lamellar tears always grew up toward the weld toe. However, in fatigue loading, cracks grew up and down simultaneously form both the weld toe and the top of lamellar tears because of stress concentration. In fatigue loading, delaminations and decohesion of inclusion/matrix interface generated in multipass welds provided crack propagation paths and enhanced crack propagation because the tips of delaminations and deconhesios acted as stress raisers.