• 한국정밀공학회지
• /
• 제14권5호
• /
• pp.22-33
• /
• 1997

This paper describes a research work of developing a computer-aided design of blanking and piercing for stator and rotor parts. Based on knowledge-based rules, the die design system, STRTDES2, is designed by considering several factors, such as complexities of blank geometry and punch profile, and availability of press equipment and standard parts. Therefore this system can carry out a die design for each process which is obtained from the result of an automated process planning system, STRTDES1 and generate part drawing and the assembly drawing of die set in graphic forms. Knowledges for die layout are extracted from plasticity theories, relevant references and empirical know-hows of experts in blanking industries.

• 한국정밀공학회지
• /
• 제17권9호
• /
• pp.102-108
• /
• 2000

A finite element analysis has been performed to investigate the effect of v-ring indenter on the sheared surface in the fine blanking of a pawl which is a part of the automotive safety belt and is made of S45C sheet. In the present analysis the Cockcroft and latham fracture criterion and the element kill method are used in order to simulate the blanking operation successfully. The simulation results are obtained for various positions and heights of the v-ring indenter. And the theoretical results are compared with available experimental results. It is shown that this FEM simulation result can be useful for predicting the optimal fine blanking condition of real products.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.598-602
• /
• 1996

This study is performed for investigating the effects of stripping and counter punching force on shearing characteristics in fine blanking, such as camber, burr-height and dimensional accuracy, etc by experiments. Conventional hydraulic press equipped with specially designed hydraulic unit is used for experiments so that both the stripping force and counter punching force are arbitrarily adjusted according to experimental conditions. Two kinds of materials, hot rolled steel sheet(1mm, 3mm) and pure aluminum(1mm, 3mm) are selected in order to examine the influence of strength and thickness of working materials in blanking of T-shaped products. Based on the experimental results of this study, it can be concluded that the finely cut surface of sheared blank can be obtained even in conventional hydraulic press if additional equipments and special dies are employed.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2016년도 추계학술논문요약집
• /
• pp.191-192
• /
• 2016

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.40-51
• /
• 1996

This paper describes some research works of computer-aided design of blanking and piercing progressive die for stator and rotor parts. An approach to the system is based on knowledge based rules. The deveolped system is composed of six modules such as main program, input and shape treatment, production feasibility check, strip layout, die layout and drawing edit module. Using this system, design parameters ( geometric shapes, die and punch dimensions and dimensions of tool elements) are determined and output is gen- erated in graphic from. Knowledges for tool design are extracted from the plasticity theories, handbooks, relevant references and empirical know-hows of experts in blkanking companies. The developed system provides powerful capabilities for process planning and die design of stator and rotor parts.

• 프린팅코리아
• /
• 제11권4호
• /
• pp.118-119
• /
• 2012

영신기계(주)(대표이사 이태호 이경택, www.diecuter.co.kr)는 지난 3월 3일 서울, 광주, 대전 등 전국 각지의 고객 및 관련사 대표 100여명을 초청한 가운데 대구 공장에서 레보텍 106SB 블랭킷 시스템 시연회를 개최했다. 특히 이번에 공개된 라보텍 106SB는 영신기계가 드루파2012에 출품할 전략 모델이어서 참관객들의 큰 관심을 불러 일으켰다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.679-682
• /
• 2001

An experiment is carried out to investigate the influences of shearing characteristic factors for the process design of lead frame blanking in copper alloy C194(t=0.205mm). 3 process parameters, e.g., clearance between die and punch, strip holding pressure, and bridge allowance are selected for this study. From the basis condition 6% clearance, 20N/$mm^2$, and 1.5t bridge allowance the seven times of experiment are done by varying the each factor. The square shape specimen is used to study the characteristics of shearing factors. The ratios of roll over, burnish, fracture zone are measured after blanking. The experimental analysis shows that the burnish ratio is decreased as the clearance increases. And the larger strip holding pressure is shown that the roll over and burnish ratio are both decreased. It is found that an optimal strip holding pressure is need for large burnish zone. Finally it is shown that the bridge allowance is less affected than clearance and strip holding pressure.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.66-71
• /
• 2008

The data of the deformation and the stress according to time are studied at upper model of press and lower model of the blanking plate applied by press with the width, length and height of 0.4 m and 0.6 m respectively. The press is pushing downward on the plate fixed at the lower floor. These data are compared and investigated through this study. By using these results, there is the maximum deformation at 4 corners in the lower plate model of aluminium alloy fixed at lower floor. This deformation incase of elapsed time of 0.6 second becomes 4 times as much as in case of elapsed time of 0.2 second. The quantity of deformation at the lower plate model becomes more than at the upper press model to the extent of 10%. At the lower plate model of aluminium alloy, there is the maximum Von-Mises equivalent stress at 4 corners and both sides of middle area on the lower plate model of aluminium alloy. This stress in case of elapsed time of 0.6 second becomes 6 times as much as in case of elapsed time of 0.2 second. The Von-Mises equivalent stress of lower plate model becomes 2 times as much as that of upper press mode.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.87-93
• /
• 2004

An experimental is carried out to investigate the characteristics of blanking for nickel alloy Alloy42 (t=0.203mm), a kind of IC lead frame material. By varying clearance between die and punch the shapes of shear profile are examined. Finite element analysis with element deletion algorithm for ductile fracture mode is also carried out to study the effect of clearance theoretically and to compare with experimental results. The rectangular shape specimen with four different comer radius is used to study the characteristics of blanking for straight side and comer region simultaneously. As the result the ratios measured k(m experiment of roll over, burnish and fracture zone based on initial blank thickness are compared with those of FE analysis. Both experiment and FE analysis show that the amount of mil over and fracture is increased as the clearance increases. When the radius of comer is less than thickness of blank it has been found that larger clearance is required than that of straight region in order to maintain same quality of shear profile at the comer region.

• 한국정밀공학회지
• /
• 제13권5호
• /
• pp.157-163
• /
• 1996

This paper is concered on the development of low-cost fine blanking die with two fluid chambers of which the pressure can be controlled by a hydraulic unit and its application to producting circular blanks in a conventional hydraulic press, not in a special triple-action press usually adopte in fine blanking operation. Four important working parameters affecting on the precision accuracy of products such as existence and position of Vee-ring, stripping force and counter punching force are primarily considered for experiments. Finite element analysis by suing ABAQUA software is approxi- mately made for blanking of circular specimen with a flat stripper plate and then compared with experimental measurements. The the theoretical prediction of camber height which represents deflection of a dish-shaped specimen after blanking seems to give a qualitatively good agreement. It is shown through experiments the the camber height decreases with decreasing stripping force and also with increasing counter punching force, but particularly depending on the latter much more than the former.