• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1209-1211
• /
• 2001

Generally, the current controller is located inner the whole controller, so the characteristic of the current controller is important in controlling performance of the upper controller. A current control loop in motor control is designed so that it is 10 times faster than the speed control loop of the upper controller. Thus, the current controller with complex control algorithm is not proper. In this paper, the improved current controller using a conventional digital PI controller and feedforward controller for the brushless BC motor is designed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.599-601
• /
• 2001

This paper investigates the permanent magnet (PM) overhang effect on the characteristics such as cogging torque and torque in brushless DC motor (BLDCM). The overhang effect has been used to enlarge the performance of the radial flux density in BLDCM and balance the force in the axial direction for the reduction of the vibration. 3D equivalent magnetic circuit network method (3D EMCNM) is used for the accurate and efficient analysis. The characteristics of BLDCM are analyzed according to the variation of overhang length and the optimal length and ratio of overhang is determined.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.840-842
• /
• 2001

The cogging torque and torque ripple in motor which cause noise and vibration are an inevitable phenomenon and they give a bad effect to motor performance. So we are required to reduce the cogging torque and torque ripple not by electrical controlling but by changing the inner mechanical structure and we focused on the permanent magnet. In this research, we calculated current, torque, Back-EMF(electromotive force) and cogging torque according to the change of the magnet shape using two dimensional FEM(Finite Element Method). Maxwell stress tensor and time-stepping method. From the results, we present an appropriate model that can satisfy both low cogging torque, low torque ripple and high efficiency.

• 한국자동차공학회논문집
• /
• 제15권3호
• /
• pp.99-105
• /
• 2007

Currently, BLDC fuel pump was applied on LPi vehicle using 3rd fuel supply system as liquified phase LPG injection method had already shown better performance than others. Its cost, however, is rather expensive because of drawbacks such as complicated structure, a fault of localization of system. In this work, demonstration system for a developed turbine type fuel pump to replace BLDC system was setup and investigated. This study results that fuel mass flow rate of turbine type pump and injection performance of injector were better compared to BLDC type. Comparing flow rate of summer LPG with that of winter LPG, the flow rate decreased about 25% using winter LPG. Performance applying turbine type LPi fuel pump to engine is confirmed.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.134-143
• /
• 2016

This paper proposes a novel asymmetrical interior permanent magnet (IPM) brushless DC (BLDC) motor structure, which utilizes half-type permanent magnet (PM) configuration and has asymmetrical side gaps (slot next to the PMs) for reducing torque ripples. This structure uses 24% less volume of PMs than conventional IPM BLDC motor with a full set of magnets. The characteristics of the proposed motor are compared with three other half-type IPM BLDC motors through finite elements method (FEM) analysis, and the usefulness of the proposed motor was verified through experimental evaluation on prototypes of the conventional motor and proposed motor under various torque load conditions. This research obtained a high-performance IPM BLDC motor while decreasing manufacturing cost at the same time.