• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.2
• /
• pp.242-250
• /
• 1999

This paper presents an estimation scheme of the external torque applied on the motor by using measured motor input current when the IPM(Interior Permanent Magnet) rotor type BLDC motor operates with constant speed. In general, the BLDC motor is controlled by vector control method. If it could be operated at over critical speed, the control scheme must be modified to flux-weakening control method. The external torque applied on the motor using flux-weakening control method could not be calculated by conventional torque equation because the demagnetizing current Id exists in the motor input current. In this paper, the commonly used flux-weakening control method is studied and the modified torque estimation scheme is suggested. The estimation scheme has been verified by the simulations and experimental results.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.309-314
• /
• 2003

High-efficiency turboblowers in the next generation have been successfully developed and commercialized first in the world, using the high-speed BLDC motors and the foil air bearings. About 20-35% savings in electricity consumption in the field are found in comparison with the conventional roots rotary blowers and the integral gear-driven turboblowers. Current TB75 and TB150 products are replacing the existing blowers in the worldwide market.

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.438-441
• /
• 1989

In this paper the phase advance method is adopted for torque characteristics improvement of brushless D.C motor and the effect on motor characteristics is investigated. The optimal commutation position is calculated by computer simulation. This paper also implements a driver for brushless D.C motors using single-chip microprocessor, 8751.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.9
• /
• pp.396-402
• /
• 1986

Although the structure of the brushless DC motor is similar to the one of the permanent magnet synchronous motor, its operating characteristics are the same as those of the permanent magnet DC motor. This is the reason that the commutators and brushes in the permanent magnet DC motor can be replaced by the power semiconductor devices and rotor position sensors for the brushless DC motor. In this paper, a current control method is presented to make a sinusoidal current waveform for constant torque generation and the operating characteristics of the brushless DC motor using the resolver as the rotor position sensor is also presented and experimented.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.11 no.1
• /
• pp.9-15
• /
• 2001

브러쉬 없는 직류전동기의 위치제어를 위한 퍼지가변구조제어기를 설계한다. 특히 본 논문에서는 기존의 퍼지제어 기법에서 얻을 수 있는 특징으로부터 하나의 전건부 변수만을 가지는 간단한 퍼지논리제어기의 설계를 기술한다. 가변구조제어는 시스템의 파라메터 변화나 외란에 둔감한 특성을 갖는다. 하지만 리칭페이스에서는 문제가 된다. 이를 개선하기 위하여 본 논문에서는 지수항을 추가한 비선형 슬라이딩면을 구성한다. 그리고 나서 비선형 슬라이딩 면과 슬라이딩 면의 변화율을 입력으로 하는 퍼지 제어기를 설계한다. 이러한 2-입력 퍼지가변구조제어기의 제어 규칙표로부터 하나의 전건부 변수만을 가지는 단일 입력 퍼지가변구조제어기를 설계한다. 이들 제어기의 성능을 입증하기 위하여 시뮬레이션과 실험을 수행한다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.9
• /
• pp.600-608
• /
• 1988

Although the structure of brushless dc motor is similar to that of a Permanent magnet synchronous motor, its torque-speed characteristcis are the same as those of a permanent magmet dc motor. The brushless dc motor drive systemcomposed of power converter including inverter, rotor positioning sensor and controller has been investigated for the purpose of position control when the motor is fed by a current controlled voltage source inverter. The equivalent transformation of a brushless dc motor into an separately exited dc motor has been possible with the vector control (field oriented control) technique. It is shown in this paper that the position control of a brushless dc mitor can be done fairly accurately only using q-axis current.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.2
• /
• pp.138-143
• /
• 1999

A new control method for the precision robust position control of a brushless DC(BLDC) motor for direct drive m motor(BLDDM) system using the asymptotically stable adaptive load torque observer is presented. A precision position c control is obtained for the BLDD motor system appro성mately linearized using the fieldlongrightarroworientation method. Many of t these motor systems have BLDD motor to obtain no backlashes. On the other hand, it has disadvantages such as the h high cost and more complex controller caused by the nonlinear characteristics. And the load torque disturbance is d directly affected to a motor shaft. To r밍ect this problem, stability analysis is calTied out using Lyapunov stability t theorem. Using this results, the stability is proved and load disturbance detected by the asymptotically stable adaptive observer is compensated by feedforwarding the equivalent CUlTent having the fast response.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.2
• /
• pp.85-95
• /
• 2000

This paper describes a sensorless control scheme for brushless dc motors(BLDCMs) using a phase shifter(FIPS) which can shift the zero-crossing point of the input signal with a specified amount of phase. The detection performance of the proposed FIPS is independent of the frequency of the input signal and quite robust with respect to the measurement noise. It is shown that the proposed sensorless control scheme using the FIPS is more effective in the respects of noise-robustness and cost than the previously known schemes. The generality and practicality of the proposed sensorless control scheme is demonstrated through performance analysis and experiments under various operating conditions.

• Journal of Biomedical Engineering Research
• /
• v.10 no.2
• /
• pp.139-150
• /
• 1989

A new motor-driven blood pump for artificial heart was developed. In this blood pump, a small size, high torque brushless DC motor was used as an energy converter and the motor rolls back and forth on a circular track. This movement of the "rolling-cyliner" causes blood ejection by alternately pushing left or right polyurethane blood sacs. This moving-actuator mechanism could be eliminate two potential problems of other motor-driven artificial hearts such as large size and poor anastomosis for the implantation. Theoretical analyses on the pump efficiency, the temperature rise, and the inflow mechanism were also performed. In a series of mock circulation tests, the theoretical analyses were compared to the measured hemodynamic and mechanical values. The pump system was shown to have sufficient cardiac output (upto 9 L/min), sensitivity to preload, and mechanical stability to be tested as an implantable total artificial heart.ial heart.