• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2013.11a
• /
• pp.229-229
• /
• 2013

본 연구에서는 미세 물분무 노즐의 소화성능을 분석하기 위해 유량계수, 방사거리, 방사각도, 그리고 작동압력에 따라 분사되는 물입자 크기를 측정하였다. 이를 위해서 이중 구조의 미세 물분무 노즐 LPN-61과 LPN-63을 제작하였으며, 미분무 소화설비를 구성하여 이중구조 노즐의 형상에 따라서 유동특성을 정량화하였다. 그 결과 LPN-61은 유량계수 5.116, 방사각 $120^{\circ}{\sim}125^{\circ}$로 작동압력이 $4kgf/cm^2$에서 $10kgf/cm^2$까지 증가함에 따라서 SMD는 $127{\mu}m$정도에서 $88{\mu}m$까지 입자 크기가 감소하였으며, LPN-63은 유량계수 5.121, 방사각도 $120^{\circ}{\sim}125^{\circ}$로 동일한 작동압력 범위에서 SMD는 $108{\mu}m$에서 $80{\mu}m$까지 감소하는 것을 확인하였다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.7
• /
• pp.884-891
• /
• 2016

A secondary injection system in a diesel engine has benefits: it can be controlled independently without interrupting engine control, it can be adapted to various layouts for exhaust systems, and it pose no reductant dilution problems compared to post injection systems in the combustion chamber or other supplemental reductant injections. In a secondary injection system, the efficiency of the catalyst depends on the method of reducing the supply. The reductant needs to be maintained and optimized with constant pressure, the positions and angles of injector is a very important factor. The concentration and amount of reductant can be changed by adjusting secondary injection conditions. However, secondary injection is highly dependent upon the type of injector, injection pressure, atomization, spray technology, etc. Therefore, it is necessary to establish injection conditions the spray characteristics must be well-understood, such as spray penetration, sauter mean diameter, spray angle, injection quantity, etc. Uniform distribution of the reductant corresponding to the maximum NOx reduction in the DeNOx catalyst system must also assured. With this goal in mind, the spray characteristics and impingement plate types of a secondary injector were analyzed using visualization and digital image processing techniques.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2339-2358
• /
• 1993

Since the rate and completeness of combustion in direct injection engines were controlled by the characteristics of gas flow fields and sprays, an understanding of those was essential to the design of the direct injection engines. In this study the numerical simulations of injection pressure effects on the characteristics of gas flow fields and sprays were preformed using the spray model that could predict the interactions between gas fields and spray droplets. The governing equations were discretized by the finite volume method and the modified k-.epsilon. model which included the compressibility effects due to the compression/expansion of piston was used. The results of the numerical calculation of the spray characteristics in the quiescent environment were compared with the experimental data. There were good agreements between the results of calculation and the experimental data, except in the early stages of the spray. In the motoring condition, the results showed that a substantial air entrainment into the spray volume was emerged and hence the squish motion was relatively unimportant during the fuel injection periods. It was found that as the injection pressure increased, the evaporation rate of droplets was decreased due to the narrow width of spray and the increased number of droplets impinged on the bottom of the piston bowl.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.3
• /
• pp.45-51
• /
• 2012

This work was investigated 2-stage injection strategy on combustion and emissions in a direct injection compression-ignition engine fueled with DME. Single cylinder engine was equipped with common rail. Injection pressure was 700bar, dSOI between the main injection and the pilot injection was varied. Diesel was used as compared fuel of DME in all cases. The results was shown that maximum pressure was higher than all cases and its amount of DME and diesel was similar. Regardless the pilot injection, the main fuel injection timing was same. The heat release rate of the main injection for diesel was high while that of pilot injection for DME was high. The THC was very low regardless of the fuel type and injection strategy. In the single injection, NOx was increased to retard of main injection timing regardless of the fuel type. NOx emissions was decreased with the retardation of the main injection timing regardless of the fuel type in the case of 2-stage injection strategy.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.17-23
• /
• 1998

A simplified experiment was performed to figure out the atomization characteristics of highly viscous liquid of rice-bran oil by applying ultrasonic energy to improve the atomization of spray droplets. A spray system, an ultrasonic system, and three kinds of pintle-type nozzles(pin-edge angle: 5 , 10 , 15 ) were manufactured. To investigate the effects of ultrasonic energy on the atomization of a highly viscous liquid, a phase doppler particle analyzer was used for the measurement and calculation of spray droplets data. Nozzle opening pressures were chosen of 3 levels, i.e, 10, 13, 16 MPa. As a result, it could be concluded that the ultrasonic energy was effective to improve the spray atomization when applied to the fuel by means of 3 different nozzles because of the effects of the liquid fuel cavitation and relaxation between molecules caused by ultrasonic energy. The improvement rate of the spray atomization by the ultrasonic spray atomization by the ultrasonic spray compared with the conventional spray was about 10% increase in the case of pintle type nozzles. With the increase of pin-edge angles the distribution lines by nozzle opening pressures are declined for both conventional and ultrasonic sprays. This means that the increase of the pin-edge angle improves the atomization of sprays.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.6
• /
• pp.51-58
• /
• 2006

The spray characteristics of liquid jet injected into subsonic cross-flow were investigated experimentally. Spray trajectories were captured using CCD camera. Droplet sizes were measured using PDPA and Image Express. The nozzle diameter was 0.5 mm, and its length-to-diameter ratios (L/D) ran$4.11{\times}10^6$ged from 1.0 to 6.0. Experimental results indicate that the breakup point is delayed by increasing gas momentum ratio and the penetration length is decreased by increasing Weber number. At low injection angle(${\theta}$ < $90^{\circ}$), Weber number is dominant parameter for trajectories, but at high injection angle(${\theta}$ > $90^{\circ}$), L/D is dominant parameter for trajectories rather than Weber number.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.594-600
• /
• 2016

The present study numerically investigated the gas leakage characteristics in a simplified underground combined cycle power plant. The effect of obstacles near a crack location on the gas concentration in the confined space was analyzed by using the lower flammable limit (LFL) of methane gas. When the jet flow was close to the vertical walls, the longitudinal leakage distance increased by about 60% (when an obstacles was present) compared to the case without any obstacle, because these obstacles prevented transverse flows. In addition, when an air filter was installed near to the trajectory of the gas flow, the longitudinal leakage distance was similar to the distance between the crack and obstacle, whereas the transverse leakage distance increased up to 8 times compared to the case without any obstacle. As the jet flow impacts on the obstacle and changes its direction, the gas flows recirculate. Therefore, it is necessary to consider the effect of the structure and facility locations on the trajectory of the jet flow to propose an accident prevention system in confined spaces.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.21-21
• /
• 2000

Thrust Cut-Off 시스템은 로켓 발사체의 분리시의 충격에 의한 비행방향오차 및 비행거리를 감소하고 Pay-Load 부에 추진력을 증가시키고 분리된 추진 기관부의 낙하위치 예측을 용이하게 한다. 이와 같이 중요한 역할을 하게되는 Thrust Cut-Off 시스템에서 스냅링은 핵심적인 역할을 하게 된다. 정상적인 추진체의 작동 시에는 고압의 연소가스를 지탱하고 분리 시에는 쉽게 분리되어 연소가스를 역 분사 시켜야한다.(중략)

• Journal of ILASS-Korea
• /
• v.25 no.2
• /
• pp.74-80
• /
• 2020

The jet in crossflow is a spray method used in the various air-breathing engine. In order to understand the spray characteristics in various environments, many prior studies have been conducted. However, there is a lack of understanding of the low-temperature liquid spray characteristics below 273 K. With this in mind, we tried to enhance the knowledge of the low-temperature liquid spray characteristics by identifying the penetration height of low-temperature ethanol. The experiment was conducted under phase pressure, and 273 K of air and 293, 263, and 233 K of ethanol was used. Shadowgraphy was employed to measure the liquid penetration, and Otsu's method was used to analyze the penetration height. The heights tend to decrease as the temperature of the liquid jet decreases. A correlation for the penetration height in the experimental conditions was derived and presented.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.10a
• /
• pp.29-29
• /
• 1997

화학반응 또는 화학증착분야에 주로 이용해 오던 유도플라즈마를 이용하여 고밀도의 두꺼운 세라믹 침적물을 제조하였다. Yttria Stabilized Zirconia 분말을 이용하여 최적조건에서 두께 약 5mm, 이론밀도 90% 이상의 침적물을 얻었다. 실험변수는 플라즈마 가스조성, 플라즈마동력, 입자의 크기, 용사거리 등으로 하였으며, 각각의 실험조건에서 용사된 spherodized particle을 수집하여 각 실험조건에서 용융된 입자의 상태를 비교하였다. 또, 침적물의 표면을 에칭시켜 각 실험조건에서의 침적상태를 관찰 및 비교하여 각각의 실험변수가 침적물의 밀도에 미치는 영향을 관찰하였다. 실험결과 높은 밀도의 침적물을 만들기 위해서는 분말의 용융상태, 용사챔버 내부압력, 분말분사거리가 중요한 변수임을 알 수 있었다. 실험에서 얻어진 결과는 ANOVA 통계기법으로 분석하여 단일변수의 영향뿐만 아니라 이들 영향이 서로 조합하여 결과에 미치는 조합효과도 분석하였다.