• Journal of ILASS-Korea
• /
• v.13 no.3
• /
• pp.149-155
• /
• 2008

An experimental study was performed to understand spray characteristics of the rotary atomizer for the slinger combustor. In this fuel injection system, fuel is injected and atomized in the combustor by centrifugal forces to engine shaft. The experimental apparatus consists of a high speed rotational spindle, rotary atomizer, pressure tank and acrylic case. The droplet size and velocity were measured by PDPA (phase Doppler particle analyzer), and spray was visualized by using high speed camera and Nd:Yag laser-based flash photography. From the test results, the droplet size (SMD) is largely affected by rotational speed, mass flow rate and the number of orifice. As the experimental results, we could understand the spray characteristics of the rotary atomizer for the slinger combustor and obtain the optimum shape of the rotary atomizer which is suitable for the small gas turbine engine.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.2
• /
• pp.192-203
• /
• 1990

여러 가지 다른 형태의 노즐을 공기 선회식 버너와 공기의 선회가 없는 버너(CB-125 Burner)에 장치하여 공기 분사식으로 오일을 분사하여 연소로에서 연소시켰다. 연소로는 길이 3m에 약 1m 상(3) 의 연소공간을 가졌으며 상부에는 열전대를 장치하고 하부에는 물이 흐르는 관을 설치하여 열효율을 계산할 수 있게 설계하였다. 연소로 연돌부에는 CO 하(2), CO, O 하(2) 가스 분석기를 사용하여 과잉공기량과 고온계로 배기가스 온도를 측정하도록 하였다. 모든 측정치는 연소곡선과 효율곡선에 의하여 얻어진 상수를 이용하여 계산한 연소로 성능방정식에 의하여 평가하였다. 실험치에 의해 계산한 벽면 열손실량과 열전달 공식에 의해 산출한 열손실량을 비교 분석하여 측정치의 정확도를 추정하고 과잉공기의 효과도 검토하였다. 그 결과 본 연구에서 사용된 두 종류의 버너와 여러 형태의 노즐이 오일 연소시 열효율 면에서 큰 차이를 보이지 않고 있음을 알았다.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1190-1194
• /
• 2008

The study aims to analyzed and identify the heat transfer characteristics of water-jet-impingement with use of 3-D numerical-analysis in order to design the old water duct. The temperature comparison processes were done with various duct flows. In addition, the optimal conditions of water-jet-impingement were proposed as jet-pressure, the temperature on the beat plane, and so on.

• Journal of the KSME
• /
• v.33 no.12
• /
• pp.1076-1085
• /
• 1993

레이저광이 가지는 지향성, 단색성, 공간적 집속성 등의 성질을 이용하는 각종 측정장치는 광섬 유의 발달과 새로운 신호처리계의 개발로 그 적용 범위가 점점 확대되고 있다. 레이저 도플러 신호의 위상차를 이용하여 운동상태의 입자의 크기와 속도를 동시에 측정할 수 있는 측정장치가 80년대에 실용화되어 캐비테이션, 분무노즐, 기름버너, 엔진연소 등 많은 분야에서 다양하게 사 용되고 있다. 이 측정방법은 Durst와 Zare에 의해 도플러 신호의 위상과 입자의 크기는 선형적인 함수 관계가 있음이 밝혀진 이래, Bachalo, Buchhave, Knuhfsen과 Olldag 등에 의해 급속히 발 전되었다. 현재 국내에도 덴마크의 단텍사, 미국의 에어로메트릭스사 등에서 개발한 장비가 3-4 기관에서 사용되고 있다. 이 글에서는 위상도플러법에 의한 입자의 크기측정에 관한 기초 이론을 참고문헌을 인용하여 설명하고, 단텍사에서 개발한 위상도플러 측정장치인 입자운동 해석장치 (PDA)를 사용하여 본 연구실에서 실험한 버너용 압력분사식 노즐에서 분사된 액적들의 국소부분 거동에 대해 소개하기로 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.53-57
• /
• 2007

고속회전의 원심력으로 연료를 공급하고 액체연료의 미립화를 초래하는 회전연료분무장치에 대한 분무특성 시험연구를 수행하였다. 특정한 공간상에 존재하는 액적의 특성을 이해하고자 고속회전 연료분사시스템을 설계 제작하였다. 시험장치는 고속으로 회전하는 Spindle, 회전연료노즐, 가압식 물탱크, 아크릴 케이스로 구성하였다. 액적의 크기와 속도를 측정하기 위해 PDPA(Phase Doppler Particle Analyzer)시스템을 사용하였고, ND-Yag Laser를 사용하여 분무를 가시화 하였다. 시험결과 고속회전 연료분사시스템의 분무특성을 확인할 수 있었고, 회전속도는 액적 크기, 속도, 분무각 및 분무패턴 등의 분무특성에 주요한 영향을 미치는 것으로 확인되었다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2015.10a
• /
• pp.323-324
• /
• 2015

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.30-37
• /
• 2004

The combustion and emission characteristics of a direct injection CI engine fuelled with DME(Dimethyl Ether) and diesel fuel were compared at idle engine speed(800 rpm) with various injection parameters. An optical single cylinder diesel engine equipped with a common-rail fuel injection system was constructed to investigate combustion processes of DME and diesel fuel. The combustion images were recorded with a high-speed video camera system. The results demonstrated that the DME-fuelled engine was superior to the conventional diesel engine in terms of engine performance and emissions. The optimal injection timing of DME was located around IDC(Top Dead Center), which was roughly same as that of diesel fuel. As the injection timing was advanced much earlier than TDC, NOx (Nitric Oxides) level increased considerably. NOx emission of DME was equal or a little higher than that for diesel fuel at the same injection pressure and timing because of higher evaporation characteristics of DME. Throughout all experimental conditions, DME did not produce any measurable smoke level.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.33-39
• /
• 2009

Asphalt waterproofing method has a long history over 80years since introduce to domestic market. This method has a good point as high water proofing not permeable to water by material performance of bitumen, In spite of high waterproofing, the application has become decreased. This asphalt method has some problem such as work safety, low workability by complicated work process, environmental problem in job site, it should be solve by complementary measures. 'Therefore, in this paper, suggest the principle of high pressure spray by heat cycle type equipment by analysis of exist problem and materials investigation. And. study and examine the spray type degeneration rubberized asphalt membrane materials to adopt job site. Moreover, suggest the evidence by inspection about waterproofing performance by Korean Industrial Standard through the performance test of the spray type degeneration rubberized asphalt membrane materials.

• Fire Science and Engineering
• /
• v.18 no.2
• /
• pp.41-48
• /
• 2004

We have conducted a numerical simulation under three-dimensional unsteady conditions in order to analyze the characteristics of $CO_2 $;, extinguishant transfer by varying the location of the injection nozzle, which affects the effect of a $CO_2 $;, fire fighting system used in the form of fixed systems for the marine engine room. Flow fields and $CO_2 $;, concentration fields were measured according to the location of the injection nozzle. In the case of arranging the injection nozzle on the center of the ceiling, the low-normal concentration distribution was developed along the $CO_2 $;, jet due to the downward flow created by impinging ceiling jets in the symmetric plane. The concentration line reaches its peak due to the mass transfer of $CO_2 $;, at the comer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.544-549
• /
• 2017

This paper aims to examine the effect of rotational fluid motion about the efficiency of the gas - liquid ejector, which is a core unit in a ship equilibrium water treatment system. The ejector is a device for injecting ozone into ship equilibrium by the negative pressure generated by exchange of momentum between water and ozone. The existing ejector ejects the driving fluid with a simple form. In this paper, however, a rotation induction device is applied to the driving nozzle so that the driving fluid can be rotated and injected. To investigate the flow characteristics by the rotational movement of the driving fluid, CFD was used. The pressure and flow rate of the driving fluid, the negative pressure and suction flow rate of the suction fluid in the suction part, and the discharge pressure were predicted. On the basis of the results, the efficiency of the ejector using the rotation induction system was 22.25%, which was about 1.7% better than that of the existing ejector. Finally, to verify the feasibility of the CFD, an experiment was conducted on the ejector using the rotation induction device and the results were similar to those of the CFD.