• 대한기계학회논문집B
• /
• 제28권5호
• /
• pp.545-552
• /
• 2004

The purpose of this study is to improve the prediction ability of the atomization and vaporization processes of GDI spray. Several models have been introduced and compared. The atomization process was modeled using hybrid breakup model that is composed of Linearized Instability Sheet Atomization (LISA) model and Aerodynamically Progressed TAB (APTAB) model. The vaporization process was modeled using Spalding model and Abramzon ＆ Sirignano model. Exciplex fluorescence method was used for comparing calculated with experimental results. The experiment and computation were performed at the ambient pressure of 0.1 MPa, 0.5 MPa and 1.0 MPa and the ambient temperature of 293k and 473k. Comparison of calculated and experimental spray characteristics was carried out and the calculated results of GDI spray showed good agreement with experimental results.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.1-7
• /
• 2013

DME spray characteristics were investigated about varied ambient pressure and fuel injection pressure using the DME common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system with DME cooling system was used since DME has properties of compressibility and vaporization in atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray analysis parameters were spray shape, penetration length, and spray angle at six nozzle holes. Three types of injector were used, the nozzle holes diameter were 0.166 mm (Injector 1), 0.250 mm (Injector 2), and 0.250 mm with enlargement of orifice hole from 0.6 mm to 1.0 mm (Injector 3). The fuel injection pressure was varied by 5MPa from 35 to 70MPa when the ambient pressure was varied 0, 2.5, and 5MPa. When using Injector 3 in comparison to the others, the DME injection quantity was increased 1.69 ~ 2.02 times. Through this, it had the similar low heat value with diesel which was injected Injector 1. Among three types of injector, Injector 3 had the fastest development velocity of penetration length. In case of spray angle, Injector 2 had the largest spray angle. Through these results, only the way enlargement the nozzle holes diameter is not the solution of DME low heat value problem.

• 해양환경안전학회지
• /
• 제23권7호
• /
• pp.941-947
• /
• 2017

컨테이너를 이용한 위험물의 해상운송이 증가함에 따라 적재불량으로 인한 위험물의 누설 등으로 선박에서 화재사고가 발생하고 있다. 한편, IMO(MSC.93)에서는 2016년 1월 1일 이후 건조되는 개방갑판상에 컨테이너를 5단 이상 적재하도록 된 모든 선박은 물분무창(Water Mist Lance, WML)이라는 소화장치를 선박에 의무적으로 비치하도록 규정하였다. 본 연구에서는 LS-DYNA를 이용하여 최적의 첨단곡률반경을 가지는 WML을 설계하기 위한 수치해석을 수행하였다. 첨단부분의 길이가 10 mm, 15 mm, 20 mm인 3가지 모델에 대한 해석결과 길이가 15 mm인 경우만 컨테이너 벽면을 관통하고, WML의 첨단부분에 손상을 일으키지 않는 결과를 나타내었다. 향후, 본 연구결과를 바탕으로 테스트용 WML를 제작하여 성능실험을 할 계획이며, 문제점은 지속적으로 개선해 나갈 것이다.

• 한국수소및신에너지학회논문집
• /
• 제29권2호
• /
• pp.219-225
• /
• 2018

This study was carried out to investigate the injection characteristics of 800 kPa compressed natural gas compressed natural gas (CNG) injector developed in Korea. The CNG injector with multi-holes, employed in this experiment, was designed to inject CNG in the manifold at high pressure of 800 kPa. The spray macroscopic visualization test was carried out via Schlieren photography to study fuel-air mixing process. The fundamental spray characteristics, such as spray penetration, spray cone angle and spray velocity, were evaluated in the constant volume combustion chamber (CVCC) with varying the constant back pressure in CVCC from 0 to 1.8 bar. For the safety reason, nitrogen ($N_2$) and an acetone tracer were utilized as a surrogate gas fuel instead of CNG. The surrogate gas fuel pressures were controlled at 3, 5.5, and 8 bar, respectively. Injection durations were set at 5 ms throughout the experiment. The simulating events of the low engine speed were arranged at 1,000 rpm. The spray images were recorded by using a high-speed camera with a frame rate of 10,000 f/s at $512{\times}256pixels$. The spray characteristics were analyzed by using the image processing (Matlab). The results showed the significant difference that higher injection pressure had more effect on the spray shape than the lower injection pressure. When the injection pressure was increased, the longer spray penetration occurred. Moreover, the linear relation between speed and time are dependent on the injection pressure as well.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.90-97
• /
• 2012

It is investigated of the DME spray characteristics about varied ambient pressure and fuel injection pressure using the common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system and fuel cooling system is used since DME has compressibility and vaporization in atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray was analyzed of spray shape, penetration length, and spray angle at the six nozzle holes. The 2 types injector were used, the one was 0.166 mm diameter the other one was 0.250 mm diameter. The ambient pressure which is based on gage pressure was 0 MPa, 2.5 MPa, and 5 MPa. The fuel injection pressure was varied by 5 MPa from 35 MPa to 70 MPa. When using the converted injector, compared to using the common injector, the DME injection quantity was increased 127 % but it didn't have the same heat release. Both of the common and converted injector had symmetric spray shapes. In case of converted injector, there were asymmetrical spray shapes until 1.2 ms, but after 1.2 ms the spray shape was symmetrical. Compared with the common and converted injector, the converted injector had shorter penetration length and wider spray angle than the common injector.

• 대한기계학회논문집B
• /
• 제40권3호
• /
• pp.127-138
• /
• 2016

디젤 차량의 유해배출가스인 질소산화물 저감을 위해서는 정화성능이 우수한 요소첨가 선택적 촉매환원장치가 장착되어야 한다. 본 연구에서는 3차원 오일러리안-라그랑지안 전산유체해석을 통해 요소첨가 선택적 촉매환원장치의 수송현상에 따른 화학반응과 다상유동 특성을 수치적으로 예측한다. 이때, 수치적인 분무형상은 가시화실험에서 측정된 분사속도, 분무관통길이, 분무반경, 평균액적지름과 비교를 통해 보정되었다. 그리고 해석 결과는 실제 엔진 및 차량 시험에서 측정한 질소산화물 저감효율과 비교를 통해 검증되었으며, 상대오차 5% 이하의 정확도를 보여준다. 검증된 전산모델은 요소첨가 선택적 촉매환원장치의 내부유동해석에 사용되었으며, 이를 통해 압력강하와 속도증가 특성을 분석하고, 암모니아의 농도균일도와 과잉분포 위치를 예측한다.