• 한국분무공학회지
• /
• 제7권2호
• /
• pp.16-21
• /
• 2002

Liquefied petroleum gas (LPG) has been used as motor fuel due to its low emissions and low cost. This study addresses the analysis of the LPG spray behavior near injection nozzle. The LPG spray photographs are compared with sprays of diesel fuel at the same conditions. The LPG spray photos show that the dispersion characteristic depends very sensuously on the ambient pressure soon after injection. The spray angle is very wide in a low ambient pressure condition until the saturated pressure at this test condition, but the angle value is quickly reduced at the condition over the pressure.

• 한국분무공학회지
• /
• 제3권1호
• /
• pp.1-9
• /
• 1998

Two measurement techniques of droplet sizing, an imaging technique(PMAS) and a phase-Doppler measurement technique (PDPA), have been compared using a water spray from a pressurized-type swirl nozzle. The result showed that SMD measured by PDPA was larger than that measured by PMAS by about 40 %. Such discrepancy of SMD could be explained by the fact that the light signal intensity used by PDPA can be biased towards larger particles. On the other hand there could be lower opportunity to capture the images of the large particles with PMAS, since the large particles could be out of sight due to their high speed.

• 동력기계공학회지
• /
• 제13권3호
• /
• pp.20-26
• /
• 2009

디젤기관에서 배출되는 유해배출성분인 NOx(Nitrogen oxides)와 PM(Particulate matter)은 기관 실린더내의 혼합기 분포에 의해 그 생성이 지배된다. 이 때문에 그 유해배출물들을 저감하기 위해서는 연소의 전단계인 혼합기 분포 및 그 생성과정의 해석은 매우 중요하다. 디젤기관에서 노즐로부터 분사된 연료는 주위기체와 혼합기를 형성하는 과정에서 액체에서 기체로 상변화를 동반한다. 따라서 분무의 혼합기형성과정을 해석하기 위해서는 액상과 기상을 동시에 분리하여 계측하는 것이 필요하다. 그러므로 본 연구에서는 디젤분무를 대상으로 Melton 등이 제안한 엑시플렉스(Exciplex) 형광법을 이용하여, 분무의 액상과 기상을 동시에 2차원분리해서 가시화촬영을 행하였다. 그 엑시플렉스 형광법을 이용하여 획득한 이미지에 화상 응용해석을 실시하여 비정상증발디젤분무의 혼합기형성과정에 대한 정보를 얻고자 하였다. 엑시플렉스 형광법을 이용해서 증발분무의 거동측성을 해석한 결과 프랙틸해석을 이용한 분무 흐트러짐(Disturbance)의 평가에서 플랙틸차원은 분사압력의 변화에 관계없이 하나의 값, 약 1.1로 정리 할 수 있고, 그 결과 각 분사압력에 대한 분무 기상외곽곡선(외주)은 거의 동일한 정도의 요철형상을 갖는다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2366-2371
• /
• 2007

Spray combustion characteristics of a conducting fuel electrospray have been studied for clean combustion technology. The multiplexing system which can retain the characteristics of the cone-jet mode is inevitable for the electrospray application. Charged micro droplets can be obtained in almost uniform size during operating the electrospray in the cone-jet mode. This experiment device set up the multiplexed grooved nozzle system with the extractor. Using the grooved nozzle, the stable cone-jet mode can be achieved at the each groove in the grooved mode. This electrospray system was applied to the diffusion combustion. It is the first step to discover the diffusion combustion characteristics of the electrospray. In case of the single grooved nozzle electrospray, the diffusion flames are occurred at each jet of grooved mode and they are quite stable. The exhaust gas analysis was indicated that there is the critical point which can make very stable diffusion combustion.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.107-112
• /
• 2001

The effect of ambient gas (steam) condensation on swirl spray characteristics were studied experimentally for low subcooling condition of the liquid. The configuration of the liquid(water) sheet and the breakup modes were examined. Also variation of the discharge coefficient, breakup length, local and the cross-sectional area-averaged SMD of droplets with the liquid flow(injection) rate were obtained. The perforation breakup mode appears dominant with condensation while the aerodynamic wave breakup mode is dominant without condensation(in the air environment). The discharge coefficient, breakup length and the mean drop sizes decrease in a same manner with increasing of the liquid flow rate for both cases(with and without condensation). The condensation effects are insignificant with the discharge coefficient. However, the local and cross-sectional area-averaged SMD are larger and the breakup length becomes shorter in the steam environment. The spray angle predicted from the volumetric flux distribution along the radial direction of the sprays in the steam environment becomes larger with condensation.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.132-139
• /
• 1997

Spray characteristics of external mixing sonic twin-fluid atomization nozzles are investigated experimentally. Particle sizes are measured by the Fraunhofer diffraction method using the Malvern particle analyzer, and their radial distributions are obtained using the tomographical transformation technique. The spatial distribution of SMD shows that the drop size increases in the radial direction at a fixed liquid flow rate, and the distribution is getting uniform rapidly as the atomizing gas pressure increases. The SMD decreases as the liquid flow rate increases at a fixed GLR. It is found that the atomization efficiency of the flush type sonic nozzle is superior to that of protrusion type. The effect of laser beam diameter of the particle analyzer on the spatial SMD distribution is minor at present experimental conditions.

• 한국분무공학회지
• /
• 제13권4호
• /
• pp.173-179
• /
• 2008

The current machinery and tools of secondary channel of the nuclear power plants were produced in the carbon-steel and low-alloy steel. What produced with the carbon-steel occurs wall thinning effect from flow accelerated corrosion by the fluid flow at high temperature, high pressure. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle-installed. Wall thinning by flow accelerated corrosion occurs piping system, the heat exchanger, steam condenser and feedwater heaters etc,. Feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which will increase as operating time progress. This study describes the comparisons between the numerical results using the FLUENT code and experimental data of down scale model.

• 한국분무공학회지
• /
• 제13권4호
• /
• pp.200-205
• /
• 2008

Spray formation mechanism was controlled by a cavitation inside an injection nozzle. Nozzle geometry affects spray characteristics and formation behavior, which could determine engine performance and pollutant formation. A study was carried out on the influence of aspect ratio on cavitation inside a nozzle. The cavitation model available in Star-CD code was used to obtain cavitation behavior inside nozzle, which was compared with previous experimental results. In this paper, a CFD approach combining multiphase Volume-of-Fluid(VOF) and k-model was applied. The numerical results are similar with the experimental results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2239-2244
• /
• 2003

A new stratified charge combustion system has been introduced and developed for GDI engines. Before this new GDI system, the stratified mixture was formed by a high pressure swirl injector. But, the special feature of new system is employed of a thin fan-shaped fuel spray formed by a slit type nozzle. Also, this system has been adopted a shell-shaped piston cavity. We made high pressure gasoline injection system and investigated the fan-shaped spray characteristics such as spray tip penetration, spray angle, SMD and velocities of droplets using PDPA(Phase Doppler Particle Analyzer) system and spray visualization system to obtain the concept of the new design and the fundamental data for the next generation GDI system. The experiment was performed at the injection pressures of 5 and 9MPa under the atmospheric condition.

• 한국전산유체공학회지
• /
• 제11권4호
• /
• pp.56-61
• /
• 2006

Numerical simulation has been performed to investigate the characteristics of the mist flow through the fire suppression nozzles. The commercial CFD software, FLUENT with the proper modeling was applied for analyzing both the internal and external flow of the spray nozzles. Computations were made for the full cone nozzle in the operation range of the low pressure and high flow-rate. To validate the present computational procedure, numerical results are compared with measurements in terms of K-factor, SMD, axial spray velocity and spray angles. Numerical results suggested that the present numerical model can be used as an adequate tool for a design purpose of mist-spray nozzles.