• Resources Recycling
• /
• v.25 no.6
• /
• pp.41-49
• /
• 2016

The present study was intended to prepare cobalt oxide ($Co_3O_4$) powder of average particle size 50 nm or less by spray pyrolysis reaction using the raw cobalt chloride ($CoCl_2$) solution, in order to identify the change in the nature of the particles according to the change in the nozzle tip size. When the nozzle tip was 1 mm, it turned out that most of the droplets were spherical and the surface showed very tight structure. The average particle size of the finally formed particles was 20-30 nm. When the nozzle tip size was 2 mm, some of the droplets formed were spherical, but a considerable part of them showed severely disrupted form. particles formed showed an average particle size of 30 - 40 nm. For the nozzle tip size of 5 mm, spherical droplets were almost non-existent and most were in badly fragmented state. The tightness of surface structure of the droplets has greatly been reduced compared with other nozzle tip sizes. Average size of the formed particles was about 25 nm. As the nozzle tip size increased from 1 mm to 2 mm and 3 mm, the intensities of the XRD peaks have changed little, but significantly been reduced when the nozzle tip size increased to 5mm. As the nozzle tip size increased from 1 mm to 2 mm, the specific surface area of the particles decreased, but the nozzle tip size increased to 5mm, the specific surface area remarkably increased.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.1
• /
• pp.5-11
• /
• 2004

벽면에 충돌하는 액체 분무의 충돌 거동과 액적 비산에 관하여 실험을 통하여 조사하였다. 액체 분무는 홀노즐에 의해 직경 40mm의 충돌판에 분사하게 된다. 액체 분무는 반경방향으로 퍼져나가 5개의 영역으로 분류되어 나타내게 된다. 난류 혹은 층류 분무의 경우, 충돌판에 충돌한 후 두꺼운 액막을 형성하게 되며, 이러한 상태에서 충돌하는 분무의 비산량은 매우 적으며 충돌 거리에 영향을 받지 않는다. 한편, 파동이 있는 분무의 충돌은 수력도약(Hydraulic jump)과 함께 반경방향으로 엷은 액막을 형성하게 되며 비산율도 증가하게 된다. 액체분무의 초속도가 증가하면 비산율도 증가하게 된다. 분열이 일어난 후에 충돌하는 파동 분무의 비산율은 분열이 일어나기 전에 비해 약 2~3배 정도 크게 나타난다. 비산율은 웨버수(Weber number)를 이용하여 요약할 수가 있다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.98-103
• /
• 2002

초음파 비가진 시인 상용분무와 초음파가진 시인 개질분무, 간접진동분무, 간접진동 및 개질의 겸용분무의 네가지 경우 모두에서 분무액적의 평균직경 및 SMD가 전 영역에 걸쳐서 노즐 글에서 분무방향으로 멀어질수록 조금씩 증가했으며, 또한 초음파 비 가진시인 상용분무 경우가 초음파 가진 세경우에 비해 크게 나타났다. 초음파 가진 세가지 경우에서는 간접진동 및 개질법 겸용의 경우에서 분무액적의 미세화가 가장 우세하게 나타났다. 이는 초음파가 분무 축방향 전영역에 걸쳐서 분무액적의 미세화에 친화적임을 입증한다. 나. 분무 방향 축에서 반경 방향으로 갈수록 분무 액적의 평균 직경과 SMD는 감소하고 있으며, 반경방향 전 영역에 걸쳐서 상용 분무시의 액적이 가장 크게, 초음파겸용 경우에서 가장 작게 나타나고 있다. 이는 초음파가 분무 내부 전 영역에 걸쳐 액적의 미세화에 친화적임을 증명한다. 다. 분무액적의 크기에 따른 분무 분포도 비교에서 네가지 경우 모두에서 축 방향 거리가 멀수록 분무액적의 크기가 다소 증가함을 보였고, 축에서 반경 방향으로는 분무액적의 크기가 다소 감소함을 보이고 있다. 상용 분무와 초음파 분무의 비교에서 초음파 겸용 가진시는 상용 분무 때 보다 분무 영역 전반에 걸쳐서 미세화가 뚜렷이 우세함을 보였다.

• The Korean Journal of Pesticide Science
• /
• v.16 no.4
• /
• pp.282-287
• /
• 2012

This study was carried out to clarify the effects of the application of pesticide by different spray nozzle types on pesticide residues. The average droplet size and discharge rate were investigated when the manual compressed sprayer with two head disk type nozzle and the knapsack engine powered sprayer with two head fan shape nozzles were used. The fan type nozzles were classified into three types by the number of orifice in the nozzle. Three type nozzles tested were fan with one orifice, fan with two orifices and fan with three orifices. Fan (trade name : D-3) with 2.4 L/min. of the discharge rate and $76{\mu}m$ of the average droplet size while maintaining constant pressure $1.1{\pm}0.2$ MPa, and fan D-35 with 2.6 L/min. and $90{\mu}m$ while maintaining constant pressure $1.0{\pm}0.2$ MPa were appropriate. The orifice size of D-3 was 0.65 mm length ${\times}$ 0.45 mm width and the orifice size of D-35 was 0.62 mm length ${\times}$ 0.46 mm width. The residue levels of imidacloprid on perilla leaves among four applications by four different nozzles show significantly difference with 5% significance level. The residue levels $3.76{\sim}3.92mg\;kg^{-1}$ by fan or disk type is smaller than $4.52{\sim}4.92mg\;kg^{-1}$ by fan II or fan III. The residue levels of imidacloprid on perilla leaf were different depend on the spray nozzles type.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.12
• /
• pp.1635-1646
• /
• 1997

The nozzle length to diameter ratio of real diesel nozzles is about 2-8 which is not long enough for a fully developed and stabilized flow. The characteristics of the flow such as turbulence at the nozzle exit which affect the development of the spray can be enhanced by impinging the flow inside nozzle. The flow details inside the impinging nozzles have been investigated both experimentally and numerically. The mean velocities, the fluctuating velocities, and discharge coefficients in the impinging inlet nozzles, round inlet nozzle, and sharp inlet nozzle were obtained at various Reynolds number. The developing feature of the external spray were photographed by still camera and the droplet sizes and velocities were also measured by laser Doppler technique. The spray angle was greater and the droplet sizes near the spray axis were smaller with the impinging flow inside nozzle.

• Journal of ILASS-Korea
• /
• v.21 no.4
• /
• pp.195-199
• /
• 2016

Spraying of nozzles and design of tractor-attached boom sprayers have been studied for analysis of liquid spraying features. The following conclusions have been drawn. At all pressures, twin flat spray tips was finer than flat spray tips. A fine spray with VMD of 101 to 200 appeared at 1.5MPa. So, it was selected as the boom sprayer nozzle. In spraying uniformity analysis, Type B was proven to have more uniformity than Type A and Type C at 52.0 cm attached distance. Type A and Type C were proven to have more uniformity than Type B at 58.5 cm attached distance. It is concluded that these results reflect atomizing characteristics of nozzles during pest control with tractor-attached boom sprayer. Therefore, optimum setting will be putting Type C with 58.5 cm distance.

• Journal of ILASS-Korea
• /
• v.4 no.1
• /
• pp.45-54
• /
• 1999

The spray characteristics of a direct injection multi-hole diesel nozzle having the 2-spring nozzle holder were investigated by using the image processing system and a PDPA(phase Bowler particle analyzer) system. The spray tip penetration, the spray angle, and the droplet diameter and velocity with the variation of the pump speed, injection quantity were measured. From, the experiments, we know that there are small droplets which are not to be detected with spray image around the leading edge of the spray. In order to represent the mean characteristics of the intermittent spray very well, it is very important to set the time windows accurately. From the measurements along the axis of the spray, close to the nozzle, the initially injected droplets are overtaken by droplets that follow them. And also there are the maximum axial mean velocity and SMD at the following part of the leading edge of the spray.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.11-17
• /
• 2007

The swirl spray for direct-injection spark-ignition (DISI) engines was investigated using a nozzle whose exit surface shape was cut with a certain tapered angle. The reason for the change in spray's characteristics at various tapered angles was explained by the data correlating the taper and flow angles. The spray tended to shift its characteristics from the symmetric to asymmetric when the tapered angle was increased; furthermore, the spray penetration and spray cone angle were also increased. When the tapered angle was greater than the $90^{\circ}$ minus flow angle, an opened hollow cone spray was formed because of the fuel impingement against the tapered surface area of the nozzle exit. This behavior indicates that the reduction in the air pressure difference between the inner and outer spray of the spray can be achieved. This behavior also promises the potential use of the tapered nozzle for the case where the independence of the spray performance from atmospheric pressure and fuel temperature is desired.

• Journal of ILASS-Korea
• /
• v.16 no.2
• /
• pp.90-96
• /
• 2011

Atomized liquid jets from the washing nozzle which configured with recirculation chamber for cleaning hot-zone area are accelerated and impinged on the head lamp surface. Cleaning efficiency of head lamp can be increased with injecting washing fluids into the hot-zone area. Experimental and numerical studies with various design parameters were executed to reveal the relations between internal geometry and internal flow in the washing nozzle. Spray structures were fitted with each of the head lamp surfaces and spray nozzles were optimized to the spray pattern. The recirculation chamber induces a recirculation flow and can be decreased the pressures perturbation inside the chamber. Orifice determines the mass flow rate. When the diameter of orifice is excessively large, it showed an unstable spray pattern. As a nozzle exit angle increases, density distributions are separated with two section. Also, as a protrusion length of nozzle exit increases, spray patterns are spread into a large area and density distributions showed unstable trend.

• Journal of ILASS-Korea
• /
• v.20 no.1
• /
• pp.43-52
• /
• 2015

Experimental study was conducted to investigate the effects of ultra-high injection pressure and nozzle hole diameter on diesel flow and spray characteristics. Electronically controlled ultra-high pressure fuel injection system was made to supply the fuel of ultra-high pressure consistently. Three injection pressures, 80, 160, and 250MPa were applied. Four type of injectors with identical eight nozzle holes were used. The four injectors have nozzle hole diameters of 115, 105, 95, and $85{\mu}m$ respectively. Injection quantity and rate were measured to investigate flow characteristics according to injection pressures and nozzle hole diameters. Mie-scattering and shadowgraph were performed to visualize liquid and vapor phases of diesel spray in a constant volume combustion chamber (CVCC). Ambient conditions of high pressure and high temperature in a diesel engine were simulated by using CVCC.