• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.6
• /
• pp.1238-1249
• /
• 1989

본 연구에서는 분무체적에 영향을 미치는 분사차압, 주위공기밀도, 노즐공의 직경과 분무각을 변수로 하여 상관관계식을 이론적으로 유도하고 이를 근거로 하여 분 무의 평균공연비 증대를 향상시키는 방안을 제시하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.5
• /
• pp.2054-2060
• /
• 2011

The purpose of this paper is to investigate spray characteristics of GDI injector that is economic and environment-friendly. Injector characteristics such as penetration length, spray angle and mixture formation were measured using experimental visualization technique. Especially, it has been analyzed that the influences of ambient pressure and injection pressure on penetration length and spray angle. To visualize the spray, a constant volume combustion chamber and fuel supply system have been manufactured. A high-speed camera and LED light source have been applied to obtain spray images. The experimental and visualization result shows that the penetration length is increased as decreasing ambient pressure and/or increasing injection pressure. Also, ambient pressure and injection pressure have minor effect on the spray angle variation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.97-104
• /
• 2006

The spray and breakup characteristics of swirling liquid sheet were investigated by measuring the spray angle and breakup length as the axial Weber number Wel was increased up to 1554 and the ambient gas pressure up to 4.0MPa. As Wel and ambient gas density increased, the disturbances on the annular liquid sheet surface were amplified by the increase of the aerodynamic forces, and thus the liquid sheet disintegrated near from the injector exit. The measured spray angles according to the ambient gas density were different before and after the sheet breaks. Before the liquid sheet breaks, the spray angle was almost constant, but once the liquid sheet started to breakup, the spray angle decreased. And the breakup length decreased because of the increase of the aerodynamic force as the ambient gas density and Wel increased. Lastly, the measured breakup length according to the ambient gas density and Wel was compared with the result by the linear instability theory. We found that the corrected linear instability theory considering the attenuation of sheet thickness agrees well with our experimental results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1011-1016
• /
• 2008

Jet-A spray and combustion were numerically analyzed in annular type combustor model using KIVA3V. The combustor geometry have 6 dilute holes. Swirl effect and thermal NO were considered in this investigation to analyze mixing and combustion characteristics. Fuel vapor, flame temperature, NO generation were investigated for various spray angle. As increase of spray angle, Jet-A vapor appeared uniformly in primary zone and evaporation rate was increased. Mixing between fuel vapor and ambient gas was enhanced as increase of spray angle. As a result, high temperature region appeared widely and thermal NO generation rate was increased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.14-25
• /
• 2021

An experimental study was conducted on the spray characteristics of the pintle injector by opening distance. The discharge coefficient of the pintle injector was investigated and the spray angle was measured by taking the spray image by test conditions. As a result of the measurement of the discharge coefficient, it was confirmed that the change in the discharge coefficient of the outer injector was not significant over the experimental conditions, but the change in the discharge coefficient of the inner injector was decreased as the flow rate increased. Measurement of the spray angle showed that the change in the spray angle was not significant in the conditions under which the spray was fully developed, but the spray was not fully developed at low flow rates. This confirmed the possibility of thrust control using the pintle injector.

• Journal of ILASS-Korea
• /
• v.25 no.2
• /
• pp.51-59
• /
• 2020

The purpose of this study is to propose and compare methods for measuring individual spray cone angles using spray cross-section images. In direct injection gasoline engines, it was believed that the distribution of air-fuel mixture in the combustion chamber directly affected combustion performance and emission formation. However, since gasoline direct injection (GDI) injectors have a small injection angle, interference between individual spray plumes occurs. Therefore, GDI injectors have only measured the spray angle of the entire spray. To overcome these limitations, three methods of indirectly measuring the spray cone angles of individual spray plume were presented and compared by forming sheet beams using Nd:YAG laser and acquiring spray cross-section images. Each method currently has advantages and disadvantages, and research to apply the method suitable for various GDI injectors needs to be continued.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.2
• /
• pp.23-35
• /
• 2003

"Backhole" is a new geometric parameter and is defined as an extra empty volume which is located behind the tangential entries at the rear part of the vortex chamber in the swirl injector. Backhole makes a difference to the spray characteristics of swirl injectors such as the spray angle, SMD, the mixing characteristics and so on. To find its characteristics, experiments are conducted by using a stroboscopic photography, a PDPA apparatus and a mechanical patternator. With the backhole, the mass flow rate of the swirl injector is increased and the center region of the injected flow has more large volume than that of without the backhole. Also the cone angle can be controlled by the backhole, so that the mixing efficiencies of swirl injectors are changed. Based on cold-flow tests, the swirl injector with the backhole may improve its performance.rformance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.892-895
• /
• 2017

As a component development of heavy duty industrial gas turbine combustor development program, pressure swirl simplex injector was designed and tested to figure out spray characteristics and performance. Injector flow rate as a function of pressure drop was measured and compared to the design target. Also spray shape was analyzed qualitatively and spray cone angle was measured from spray visualization image using shadowgraph. The flow test result showed that the injector was designed and manufactured correctly according to the design target and spray cone angle was measured from shadowgraph result. As a next step, PDA (Phase Doppler Anemometry) measurement is planned to figure out more specific spray performance and characterization.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2147-2159
• /
• 1991

The effects of principal dimensions of internal mixing twin-fluid atomized and operating conditions on the atomizing characteristics are experimentally investigated. The tests are conducted over the wide range of air/liquid ratio to predict influences of the diameter and length of nozzle, contacting angle between air and liquid in the mixing chamber, and air orifice diameter on the mean drop size(SMD), spray angle, distribution of drop size, and spray dispersion, And also, initial distribution of liquid column by air stream within the mixing chamber are observed through the transparent nozzles. A He-Ne laser particle sizer(MALVERN Model 2604) was used to measure the Sauter.s mean diameter( $D_{321}$) and droplet sizes distribution. In this experiment the air/liquid ratio, mixing length and nozzle diameter have a great influence on SMD, spray angle, droplet sizes distribution and spray dispersion.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.526-530
• /
• 2009

본 연구은 자동차용 가솔린엔진에 장착되는 인젝터의 연료공급 특성에 대한 것으로, 가솔린 엔진의 전자제어식 포트 연료분사는 분무장치와 흡기포트의 최적화 및 분무특성이 우수해야 엔진의 성능 향상 및 배기가스 저감의 목적을 이룰 수 있다. 4홀과 12홀 인젝터의 장착각 변화와 포트 마스킹의 형상변화에 따른 벽유량을 측정?분석하였고 분무가시화 실험을 통하여 분무성장과정과 분사각, 연료미립화 및 분무도달거리를 분석하였다. 벽류측정 실험을 통하여 벽류는 미립화정도와 흡기유동과 유속에 가장 큰 영향을 받는 것으로 판단되며, 12홀 인젝터 대비 4홀 인젝터는 분무압력에 따라 분무특성의 변화량이 크게 나타났다.