• Journal of the Korean Magnetics Society
• /
• v.15 no.3
• /
• pp.191-197
• /
• 2005

In the fabrication process of Fe-based amorphous alloy powder cores by pulverization of the melt-spun ribbons and cold compaction, the effects of powder preparation method on the magnetic & electric properties, powder shapes and microstructure of cores have been investigated. The powder cores made by using rotor mill showed low effective permeability as compared to the cores prepared by ball milling. However the frequency dependence and quality factor properties were superior in the case of rotor-milling. Further the powders prepared by rotor mill had homogeneous and round shapes through strong shearing in the sieve ring, while the ball milled powders were inhomogeneous and relatively small. The lower permeability of the powder cores fabricated with rotor mill was considered to be due to the high internal stress occurred by very intensive shearing. Moreover the powder cores produced by rotor-milling showed lower core loss and good frequency dependence of effective permeability possibly due to the higher electrical insulation between magnetic particles. The dc bias property of the powder cores made by rotor-milling was better than the one by ball-milling.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.04a
• /
• pp.11-12
• /
• 2006

• Journal of the Korean Magnetics Society
• /
• v.14 no.1
• /
• pp.7-12
• /
• 2004

The annealing-temperature dependence of magnetic properties in compressed powder cores being composed of ball-milled F $e_{73.5}$C $u_1$N $b_3$S $i_{15.5}$ $B_{7}$ alloy powders (size 250∼850${\mu}{\textrm}{m}$) and 5 wt% of ceramic insulators has been investigated. When annealed at 5$50^{\circ}C$ for 1 h and so transformed to $\alpha$-Fe phase nanocrystalline structure with the grain size of 11 nm (electrical resistivity : 110 $\mu$Ω$.$cm), the highest effective permeability of 125 and quality factor of 53 were obtained, and the permeability persisted up to about 500 KHz. Further the core loss measured at the frequency of 50 KHz and the induction amplitude of 0.1 T was very low (230 mW/㎤). However the dc bias characteristics was not satisfactory as compared to that of conventional powder core materials(MPP, Sendust etc.). The inferior dc bias property of F $e_{73.5}$C $u_1$N $b_3$S $i_{15.5}$ $B_{7}$ alloy powder cores was attributed to the fact that the size of powder was too large for obtaining the same permeability with that of conventional materials.

• Journal of Powder Materials
• /
• v.11 no.4
• /
• pp.348-350
• /
• 2004

최근 들어 노트북, 통신장비 등 고성능 전자기기들은 산업수요의 특성상 소형화와 경량화 추세가 가속화되고 있으며, 컴퓨터, 냉장고, 에어컨 등 가전제품에 있어서도 안정한 전류공급 및 역률의 향상이 의무화되고 있다. 따라서 내부에 사용되는 부품의 고주파화, 고효율화, 손실감소를 위한 고성능 연자성코아 (그림 1. 참조) 개발의 필요성이 한층 증대되고있는 실정이다. (중략)

• Journal of the Korean Magnetics Society
• /
• v.6 no.6
• /
• pp.388-396
• /
• 1996

Magnetic properties of sintered Fe-79Ni-4Mo cores made of centrifugal atomized powders were investigated. $H_{c}$ and $\mu_{a}$ of the cores sintered at $1350^{\circ}C$ for 2 hours measured at 60 Hz at a magnetic field of 10 Oe showed the best properties. Particularly the properties of $H_{c}$ and $\mu_{a}$ measured at low field (< 0.2 Oe) were found to increase with increasing the particle size of the core samples. It resulted from the domain wall motion depending on the grain size of sintered bodies. The best D, C magnetic properties of $H_{c}$ and $\mu_{max}$ were 0.085 Oe and 40000, respectively. A, C properties of the same cores showed the $\mu_{a}$ of 11000. The magnetic properties of sintered cores always exhibited an enhanced AC/DC performance by using the powders mixed with two different particle sizes. Those properties of cores are expected to apply for current transformer.

• Journal of the Korean Magnetics Society
• /
• v.10 no.1
• /
• pp.11-15
• /
• 2000

13Cr-1.5Nb-Fe alloy powder prepared by water atomizing method is reduced with flowing hydrogen gas. The characteristics of a reduced alloy powder is investigated and magnetic cores formed by using the reduction power sintered in the vacuum of ∼10$\^$-5/ Torr. In order to study on the magnetic cores permeability and power loss in alternating magnetic field are also measured. The result of particle size distribution shows the paticle size is 70 ㎛ at volume fraction of 50 %. The saturation magnetization of the reduced alloy powder is 160 emu/g. The relative peak permeability (H$\_$a/=5Oe) of a magnetic core is 400 and the power loss (B$\_$m/=80G) 0.12 mW/cc at sintering temperature of 1,200 $\^{C}$, 10 ton/㎠ forming pressure, and 1 kHz.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2010.06a
• /
• pp.157-158
• /
• 2010

• Proceedings of the Korean Magnestics Society Conference
• /
• 2010.06a
• /
• pp.142-143
• /
• 2010

• Journal of the Korean Magnetics Society
• /
• v.12 no.6
• /
• pp.218-223
• /
• 2002

We investigated the magnetic properties of High Flux-type $Ni_{x}Fe_{100-x}$(x=40∼50, wt.％) permalloy powders and dust cores. The powder was prepared by conventional gas atomization in mass production scale. At the composition of $Ni_{x}Fe_{55}$, saturation magnetization was maximum. In case of lower Ni content than X=45, the $M_{s}$, decreased largely with the decrease in Ni content, which is due to the invar effect. The permeability of compressed powder cores increased with the decrease in Ni content, which was considered to be due to the decrease in the magnetostriction. In addition, the dust core with Ni=45％ showed the lowest core loss because of the increase in electrical resistivity leading to the low eddy current loss. From the better frequency dependence of permeability, larger Q value and superior DC bias characteristics of Ni=45％ than those of Ni=50％ core, it was confirmed that the 45％Ni-55％Fe powder alloy was better material for the dust core than commercial High Flux core materials.

• 대한치과보철학회:학술대회논문집
• /
• 1996.11a
• /
• pp.52-52
• /
• 1996