• Electrical & Electronic Materials
• /
• v.6 no.2
• /
• pp.168-174
• /
• 1993

두가지 부분수산법, 즉 부분수산법(1)과 수정된 부분수산법에 의해 합성한 미분말을 사용하여 PZT 세라믹스를 저온소성하고 그 전기적 제특성을 조사하였다. 두가지 부분수산법에 의해 합성한 분말의 소결거동을 조사해본 결과 고상반응법보다 훨씬 낮은 소결온도인 950.deg.C에서도 단일상의 페로브스카이트상이 얻어지고 치밀화가 이루어졌을 뿐만 아니라 비유전율, 전기기계 결합계수, 압전정수 등 유전 및 압전특성이 고상반응법에 비해 손색이 없었다. 특히 두가지의 부분수산법에 의해 얻어진 PZT 세라믹스는 물리적 전기적 제특성이 서로 비슷하게 나타났으며 이 결과로부터 부분수산법(1)에서 수반되는 ZTO 분말을 따로 합성하는 공정이 불필요한 수정된 부분수산법이 편리함을 알았다.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.2
• /
• pp.55-66
• /
• 2017

The standard piezocone penetration rate of 2 cm/s is proposed in specifications regardless of soil type. However, conditions of standard Piezo Cone Penetration (CPTU) Testings in silty soils with low plasticity vary from undrained to partially drained or fully drained penetration conditions. The partially drained shear strengths of Incheon, Hwaseong and Gunsan silty soils were estimated from the analysis results of the distributions of CPTU-based shear strengths. The CPTU-based shear strengths were compared between the undrained shear strength line and the fully drained shear strength line, which were determined from approximately ${\varphi}^{\prime}=3^{\circ}$ and ${\varphi}^{\prime}=15^{\circ}$, respectively. The internal friction angles obtained from the back analysis and UU-tests tended to increase with decreasing plasticity index, which range approximately from ${\varphi}^{\prime}=2^{\circ}$ to ${\varphi}^{\prime}=14^{\circ}$. The results matchs well with CPTU-based estimation results.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.817-827
• /
• 2008

The seismic performance of a column splice fabricated with PJP (partial joint penetration) welds for special moment frames was experimentally evaluated in this study. The steel materials that were used for the specimens included SHN490 and SN490 steel, or the newly developed structural steel for seismic application. Fabricating the column splice with PJP welds is highly attractive from the perspective of reducing the welding cost and the construction time. PJP welds in column splices are viewed apprehensively, however, because several tests have shown that PJP welds in thick members tend to become brittle under tensile loads. The column splices in this testing program were designed for the expected plastic moment of the column that current seismic codes typically require. The design strength of partial-penetration welded joints was determined according to the 2005 AISC-LRFD Specification. Three-point loading was applied monotonically, using a universal testing machine, such thatthe column splice joints were subjected to pure tension. The test results showed that the PJP welded splices, if designed properly, can develop a strength exceeding that of the actual plastic moment of the column. The specimen made of the SM490 rolled section, however, showed a brittle fracture at the splice soon after achieving the actual plastic moment of the column. The tensile coupon test results also showed that the material properties of SM490 steel are more unpredictable. Overall, although the test data are limited, the SHN490 and SN490 steel specimens showed a superior and reliable performance.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.171-171
• /
• 2007

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.1
• /
• pp.34-40
• /
• 2011

The bulk density, water absorption and microstructure of the artificial aggregates were controlled as a function of sintering temperature (1100 and $1200^{\circ}C$) and time (10~60 min) in the fabrication process of the artificial aggregates by the direct sintering process using dredged soil, the inorganic wastes. Also, the physical properties of the artificial aggregates fabricated according to the different sintering methods such as the direct sintering method used in this study and the increasing temperature sintering method used in the previous report, were compared and analysed. The bulk density of aggregates sintered at $1200^{\circ}C$ by the direct sintering method showed below 1.0, and the thickness of a shell and the pore size of the black core were increased with sintering temperature. Also, in the same sintering temperature, the area of black core was decreased, the thickness of shell was increased and the water absorption was decreased with sintering time. The black core of artificial aggregates of bulk density below 1.0 had the similar microstructure, regardless of sintering methods. In contrast, the shell of aggregates fabricated by the increasing temperature sintering method showed more dense microstructure than that by direct sintering method, hence the water absorption of aggregate sintered using direct sintering was relatively high. Thus, the direct sintering method is suitable for fabrication of artificial aggregates in ceramic carriers or absorbents applications.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.1
• /
• pp.25-31
• /
• 2003

This research aimed to experimentally and theoretically investigate the moment strength of deck plates. A moment experiment was carried out using a full-scale 14 specimen. To prevent local buckling, the point load was applied at 1/4 points. After the experiment, theoretical analysis was conducted and the differences between various codes were identified. The experimental results were compared with AISI (the American Iron and Steel Institute), EC (Euro Code) 3, and KS (Korea Standard) codes. Analysis results are summarized as follows: (1) the failure mode was influenced by local buckling at the midpoint of the beam and/or at the intermediate loading point: (2) if yielding first occurred at the tension side, the moment strength would increase as the plastic reservation of the tension zone acted: (3) the experimental results were closest to the EC3 codes in which the partial plastic reservation was considered; (4) statistical evaluation based on the EC3 Annex Z showed that the partial resistance safety coefficient calculated applying to the EC3 formula, $^{\circ}{_M}$, was placed within 1.1 which was the target value of EC3 code; and (5) the analytical power of AISI and KS codeswere expected to improve into the level of EC3 codes if the concept of plastic reservation of the tension side would be introduced to them.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.2
• /
• pp.187-192
• /
• 2016

While structures are designed within elastic range by other designs, plastic behavior of structures should be verified and controlled in order to prevent structural collapse by the earthquake resistant design. No Collapse Requirement for typical bridges is to avoid falling down of superstructure by way of plastic behavior of certain structural elements and to operate emergency vehicles after earthquake. Such plastic behavior is restricted to connections or pier columns and appropriate measures are required for each case. Earthquake Resistant Design part of Roadway Bridge Design Code provides design processes for Ductile Collapse Mechanism by forming plastic hinges at pier columns. Also for bridges with reinforced concrete piers ductility-based design processes are provided as an appendix constructing Brittle Collapse Mechanism with connection yielding. In this study, a typical bridge with steel bearing connections and reinforced concrete piers is selected and No Collapse Design procedure considering both Ductile and Brittle Collapse Mechanism is proposed together with revisions required for the Earthquake Resistant Design part.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.251-258
• /
• 2000

Based on the numerical investigations using steel bridge pier subjected to strong seismic excitations a new approach to seismic damage assessment for steel structures and their members has been proposed in conjunction with the suggested definition of failure state. The relevant failure form of the steel pier is evaluated. It is revealed that when a seismic load has a short period, the failure of global buckling beyond the allowable displacement is more dominant than that by that of the local buckling caused by the accumulation of plastic strain. When a seismic load is not beyond this certain part, but repeats within the range of where a plastic deformation occurs, the plastic strain is accumulated on the partial element of bottom edge of steel pier and the failure occurs by the local buckling from the accumulated plastic local strain.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.9
• /
• pp.17-27
• /
• 2016

Parial drainage characteristics of clayey silt with low plasticity from the west coast (Incheon and Hwaseong) was analyzed using CPTU based existing correlation equations and compulsory replacement method. Generally, the estimated $OCRs={\kappa}{\cdot}((q_t-{\sigma}_{vo})/{\sigma}^{\prime}_{vo})$ using Powell and Quartman(1988) were higher than those obtained by the oeodometer tests. These trends were noticeable for the layers containing a lot of silty and sand soils. The assessment of partial drainage conditions was performed through Schnaid et al. (2004)'s equation; it is based on plotting the normalized cone resistance, $Q_t$ versus the pore pressure parameter, $B_q$ in combination with the strength incremental ratio, $s_u/{\sigma}^{\prime}_{vo}$ to the CPTU data. It is evident that more than half of the data fall in the range where $B_q$ < 0.3, corresponding to the domain in which the partial drainage prevails when testing normally consolidated soils at a standard rate of penetration (2 cm/s). To estimate the replacement depth of clayey silt with low plasticity, back analysis was carried out to evaluate the internal friction angle based on where the design depths are equal to the checked depths using bearing capacity equation. The internal friction angels obtained from the back analysis tended to increase as the plasticity index decreases, which is ranged approximately from ${\varphi}^{\prime}=2^{\circ}$ to ${\varphi}^{\prime}=7^{\circ}$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.244-244
• /
• 2003

나노인덴테이션은 시편에 압자를 침투시켜 재료의 기계적 특성을 파악할 수 있는 경도시험법이다. 압입범위를 나노미터범위로 조절할 수 있어 기존에 접근할 수 없었던 극 미소부분에로 응용이 넓어지고 있다. 경도시험시 재료의 탄성 및 소성 작용에 의해 재료는 변형되고, 표면변화 관찰을 통해 표면아래 부분에서 이루어지고 있는 거동을 예측할 수 있다. 이러한 관점에서 나노인덴테이션 시험시에도 발생하는 파일업과 싱크인 현상에서 재료가 나노미터 범위에서 어떠한 양상으로 변형을 하는지를 고찰하는 것은 의미가 있을 것이다. 본 연구에서 파일업과 싱크인의 양상을 파악하고 그 양을 정량화하기 위하여 가공경화양에 따른 표면변화와 압입하중 변화에 따른 표면변화를 관찰하였다. 어닐링한 봉상 알루미늄을 압축변형을 0%, 5%, 20%, 40%, 50% 로 변형시켜 가공경화를 일으켰고, 표면은 전해연마하여 나노압입시험이 가능하도록 하였다. 각각의 시편을 나노인덴테이션 압입하중을 변화시켜 재료에서 하중 변화에 따라 나타나는 표면변화를 관찰하였고, 위의 각 조건에서 파일업양을 정량화 하였다. 연구결과에 대해 ANSYS 유한요소분석 프로그램을 사용하여 재료의 변형양상을 시뮬레이션 하였고, 실제 실험데이터와 비교 분석하였다.