• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.117-124
• /
• 2006

The effects of binder content and recycling mixed waste plastics(PA) content on the workability, work life and hardening shrinkage of fresh polymer concrete using mixed waste plastics are examined. As a result, the workability of the polymer concretes using mixed waste plastics tend to improve with increasing binder content, PA content and filler content. The work life of the polymer concretes using mixed waste plastics is shortened with an increase in the initiator content and curing temperature. The length change of the polymer concretes using mixed waste plastics tend to increased with Increasing binder content and PA content. The result of the present research is expected to make a contribution to the recycling of final mixed waste plastics and the continuing efforts for the development of use of the recycled products are thought to expand the horizon for the recycling of the final mixed waste plastics.

• Composites Research
• /
• v.13 no.4
• /
• pp.42-53
• /
• 2000

A study has been made to establish an optimum condition in the surface treatment and curing method that is important for the fabrication of Al 7075/CFRP laminates. PAA(Phosphoric Acid Anodizing) provided a good adhesive strength and FPL(Sulfuric / Sodium Dichromate Acid Etching) had a similar adhesive strength with PAA. On the other hand, the poor adhesive strength was shown on vapor degrease and CAA(Chromic Acid Anodizing). By using the atomic force microscope(AFM), it was found that the PAA oxide surface obviously had a greater degree of microroughness as compared to vapor degrease, CAA and FPL treated surfaces. These results support the concept of a mechanical interlocking of the adhesive with-in the oxide pores as the predominant adhesion mechanism. In curing methods, the adhesive strength of co-curing method was higher than that of secondary curing method. With respect to stability of specimen shape, the secondary curing method was better than co-curing method. DMA(Dynamic Mechanical Analysis) test revealed $T_g$ in curing times over 60 min is nearly same, so it is estimated they will have similar degree of curing and joint durability in using FM300M adhesive film.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.55-63
• /
• 2012

This paper presents materials and processing technique to manufacture low viscous strain-hardening cementitious composite which is suitable for structures requiring low viscosity of materials. The micromechanics and fracture mechanics tools coupled with processing techniques were adopted to achieve low viscosity of composites as well as high tensile strain capacity. Optimal volume and length of fibers and interfacial properties between fibers and matrix for composites with tensile strength of 2~3MPa were determined on the basis of the micromechanical analysis and the steady-state cracking theory. Then six mixtures were determined and the experiment was carried out to evaluate the viscosity and uniaxial tensile performance of those. From the test results, it is verified that the strain-hardening cementitious composite with low viscosity suitable for grouting applications in fresh state as well as high ductility over 1.5% in hardened state can be feasible.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.13 no.1
• /
• pp.84-91
• /
• 2017

This paper is proposed to select the optimal finite element type in finite element analysis. Based on the NUREG reports, static analyses were performed using a commercial analysis program, $ABAQUS^{TM}$. In this study, we used a nonlinear kinematic hardening model proposed by Chaboche. The analysis result of solid elements by inputting the same material constants was different from the results of the NUREG report. This is resulted from the difference between shell element and solid element. Therefore, the material constants that have similar result to the experimental result were determined and compared according to element type. In case of using solid element for efficient finite element analysis, we confirmed that the use of C3D8I element type(incompatible mode 8-node linear brick element) leads the accurate result while reducing the analysis time.

• Composites Research
• /
• v.16 no.1
• /
• pp.34-41
• /
• 2003

A cure process control model was proposed to optimize the curing process of thick filament wound structure. There are two types of smart cure, one is that the boundary conditions of the hollow cylinder are same between inner surface and outer surface, and the other is that inner surface temperature is slightly higher than outer surface to initiate cure reaction from the inner side to the outer side to reduce residual stress.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.15 no.2
• /
• pp.31-39
• /
• 2019

Cracked component analysis is needed for structural integrity analysis under seismic loading. Under large amplitude cyclic loading conditions, the change in material properties can be complex, depending on the magnitude of plastic strain. Therefore the cracked component analysis under cyclic loading should consider appropriate cyclic hardening model. This study introduces a procedure for determining an appropriate cyclic hardening model for cracked component analysis. The test material was nuclear-grade TP316 stainless steel. The material cyclic hardening was simulated using the Chaboche combined hardening model. The kinematic hardening model was determined from standard tensile test to cover the high and wide strain range. The isotropic hardening model was determined by simulating C(T) test under cyclic loading using ABAQUS debonding analysis. The suitability of the material hardening model was verified by comparing load-displacement curves of cyclic C(T) tests under different load ratios.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.04a
• /
• pp.168.1-171
• /
• 1999

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.94-99
• /
• 2018

The purpose of this study is to investigate the effect of combinations of different accelerators mixed on the early age strength development of concrete of 21 to 27MPa in the curing temperature of $10^{\circ}C$ compared with existing early strength agent. The present study was assessed the early strength development of combinations of three different accelerating admixtures with early strength type agent comparing to single accelerating admixture with early strength type agent. As a result of this study, the effect of $CaBr_2+NaSCN+DEA$ combination on strength development showed better than $CaBr_2$ or NaSCN alone with early strength type agent. Therefore, we observed that concrete using $CaBr_2+NaSCN+DEA$ combination with early strength agent was achieved 5MPa 12hours earlier than use of $CaBr_2$ or NaSCN alone.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.04a
• /
• pp.95.2-98
• /
• 1999

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.122-131
• /
• 2000

In this work, the effect of chemical surface treatments on morphology of carbon blacks was investigated in terms of cure behavior and tearing energy ($G_T$) of carbon blacks/rubber composites. As experimental results, the polar or nonpolar chemical treatment led to a significant physical change of carbon black morphology. The cure activation energies (Ea) and frequency factor (A) obtained from Kissinger equation decreased with improving the dispersion of carbon flacks, resulting in high reactivity. However, a significant advantage of carbon black/rubber composites is gained by carbon blacks treated in basic (BCB) or nonpolar (NCB) chemical solution, resulting in increasing the tearing energy. These results could be explained by changes of dispersion, agglomerate, surface functional group, void volume, and cross-linking density of carbon black/rubber composites.