• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.4
• /
• pp.17-26
• /
• 1995

In general existing air conditioning devices, which are carried out by convection heat transfer, are very popular compared with the radiation type air conditioning devices. But perconal convection tpe air conditioning units are unuseful air conditioning type because it handles amount of surrounded air to meet the temperature and humidity. In this view, this study is intended to develope personal dir conditioning units using a radiation type radiator. Liquid Droplet Radiator(L.P.R.) radiates the energy by means of thermal radiation. Radiative energy from L.P.R. is the infrared rays which heat the objects without lose of energy. It is a desirable heating method for the local area within the large room. In this study, the analysis uses the Monte Carlo methd to predict the temperature distribution in the droplet sheet and the net heat flux from the L.D.R.. And for this study and experiment was carried out to analyse the radiative and convective heat transfer characteristics in the L.D.R.. And the experiment was investigated the effects of inlet temperature, feed rate, optical thickness and droplet diameter on heat transfer characteristics of L.D.R.. The obtained results from the numerical and experimental studies of L.D.R. were as follows ; (1) The heat flux of L.D.R. was effected by extinction coefficient of droplet sheet, optical thickness and droplet temperature, surface area and emissivity of the droplet. And it was increased with the temperature, feed rate and optical thickness, on the other hand decreased with increasing of droplet diameter. (2) The experimental results for heat flux was ecalucted below 20% than that of the numerical solution by Monte Carlo method, but the tendency of the variation shows relatively good agreement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.3
• /
• pp.327-336
• /
• 2016

Manufacturers of aircraft engines have introduced computer-aided manufacturing (CAM) software to operate and control computerized numerical control (CNC) machine tools. However, the generation of a CAM model is a time consuming and error-prone task since machining procedure and operational details are manually defined. For the automatic generation of a CAM model, feature recognition techniques have been widely studied. However, their recognition coverage is limited so that complex shapes such as a jet engine cannot be fully developed. This study presents a novel approach to quickly generate a CAM model from a CAD model using shape search techniques. Once an operator sets a machining operation as a reference operation, the same shapes as the shapes referenced by the operation are searched. The reference operation is copied to the positions of the searched shapes. The proposed method was verified through experiments with a jet engine compressor case.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.2
• /
• pp.154.2-154.2
• /
• 2011

행성 및 타이탄과 같은 태양계 내의 면천체(extended source)를 관측하기 위해서는 공간분해능이 높은 대형망원경과 파장분해능이 높은 분광기가 필요하다. 특히 분광 관측 자료를 이용하면 행성 및 타이탄의 대기 구성 성분 및 그 성분비, 온도 분포, 구름과 연무 등의 수직 구조 등을 알 수 있다. 최근 연구에서는 구름, 연무, 비 등의 생성 과정에 불포화/초과포화 상태의 메탄, 에탄, 에틸렌 등이 관여하는 것이 새롭게 알려져 보다 활발한 후속 연구가 필요하다. 현재 개발 중인 IGRINS는 적외선 영역의 H band($1.49{\sim}1.8{\mu}m$)와 K band($1.96{\sim}2.46{\mu}m$)를 동시에 관측할 수 있고, McDonald 2.7m 망원경에 부착할 때 R~40,000의 높은 분해능을 가지는 장비로서 태양계 천체를 관측하는 데에 매우 적합하다. 따라서 향후 IGRINS가 본격적으로 가동될 때 얻을 수 있는 자료에 대한 사전 연구가 필요하며, 이는 대형 망원경 및 고분산 분광기를 이용한 관측, 자료 처리 및 분석 등의 경험에 기반을 두어 진행되어야 한다. 이에 NIFS/Gemini에 의해 관측된 타이탄 분광 자료와 TEXES/IRTF에 의해 획득된 목성극지방의 분광 자료를 분석하는 사전 연구를 진행하고 있다. 목성에 대해서는, 극지방에서 관측되는 hotspot, warm, normal 지역의 근적외선 영역 분광선 분석을 통해 기존에 결정되어 있지 않은 극지방 성층권의 고도에 따른 온도분포를 알아본다. 타이탄에 대해서는, 근적외선 영역의 메탄흡수밴드에서 관측된 주연증광(Limb brightening) 현상을 복사전달모델로 구현함으로써 어떤 기작이 이 현상에 가장 큰 영향을 미치는지에 대해 알아본다. 이런 태양계 천체 자료에 대한 연구는 향후 mission 및 rover 작업을 수행함에 있어 기본적인 정보로서 활용될 수 있다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.4
• /
• pp.26-32
• /
• 2014

The combustion characteristics of Boron-beads to improve the energy density of gas generator has been investigated in accordance with diameter of beads and their composition. In this paper, electrically heated tungsten sheet and visualized furnace are applied to measure ignition temperature and burning time of bead respectively. The results proposes ignition temperature between 720~800 K and burning time proportional to bead diameter. Also a ignition delay of boron particle is detected through the temperature and radiation intensity measurements.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.2
• /
• pp.71-78
• /
• 2007

The heat transfer characteristics of solar tower receivers are experimentally investigated with receiver shapes. Generally, these become different according to the shapes and materials of the volumetric air receiver. In order to study these effects, the apparatus adopting laminated mesh and honeycombs as the volumetric air receiver is proposed. The receiver consists of laminated mesh (diameter; 100 mm, thickness; 1 mm), honeycombs (diameter; 100 mm, thickness; 30 mm) inserted into ceramic tube (inside diameter; 100 mm, outside diameter; 120 mm, length: 1000 mm). To apply heat to the receiver, an electric heater is used. To find out the heat transfer characteristics of the laminated mesh, the air temperatures are obtained by installing 3 thermocouples on each layer, dividing ceramic tube into 4 layers. Also, a radiative shield is installed to measure the only air temperature. The data for laminated mesh and honeycomb thickness of 30, 60, 90 mm are obtained. The results show that the temperature of layer 3 is higher than those of layer 2 and layer 1.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.28.3-28.3
• /
• 2009

과학기술위성 3호는 2007년 6월에 사업착수를 시작하여, 동년 8월 시스템요구사항검토회의(SRR)를 통해 임무 요구사항을 도출하였고, 동년 12월에 시스템기본설계검토회의(SDR)과 2008년 9월 시스템예비설계검토회의(PDR)를 개최하여 시험인증모델(EQM, Engineering& Qualification Model) 제작을 시작하여, 납품을 완료하고 ETB(Engineering Test Bed)상에서 유닛의 기능 시험 및 접속시험, 그리고 환경시험을 수행을 완료하였다. 또한 열구조모델 (STM, Structure and Thermal Model)도 제작을 완료하고 발사환경시험과 열평형 환경시험을 완료하였다. 이와같이 시험인증모델 및 열구조모델에 대한 지상에서의 시험과 검증이 완료된 시험결과를 바탕으로 2009년 9월 상세설계를 완료하고 비행모델 제작에 착수할 예정이다. 이 논문에서는 과학기술위성 3호의 시험인증모델에 대한 시험의 목적, 종류 그리고 검증에 대한 결과 그리고 향후 계획에 대해 발표하고자 한다. 참고로 과학기술위성 3호는 주탑재체인 다목적적외선영상시스템(MIRIS)은 우리 은하계의 근적외선 관측, 우주 배경복사 관측 및 지구 지표면의 적외선 영상 획득을 임무로 하고 있고, 부탑재체인 초소형 영상 분광기(COMIS)는 한반도 지역의 다중 스펙트럼 영상을 획득함으로써 대기관측 및 환경감시의 임무를 가지고 있다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.106-112
• /
• 2013

In this paper, human exposure of wireless devices was analyzed for various positions of the transmitter. The scenario for the position of the transmitting antenna was decided after discussion with ADD(Agency for Defense Development), and Korean male phantom model developed by ETRI were used to conduct simulations. The SAR values were analyzed by changing the position of the transmitter, and compared with Korean EMF regulations and ICNIRP guidelines. Additionally, human exposure was also investigated for two typical postures which can be posed by war-fighter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1097-1104
• /
• 2016

The infrared camera is difficult to satisfy the RE-102 specification of Mil-Std-461. Especially, in the case of UAV electronics, shielded cable is not used, so it is difficult to meet the electromagnetic compatibility standard. In the RE-102 test of the IR camera for UAV, radiated noise exceeding 30 dBuV/m was observed in the range of 50 MHz to 200 MHz. As a result of pcb em scan, peak noise which caused by the harmonic frequency of the digital control signal clock was observed. Radiated noise was reduced by up to 22.9 dBuV/m by applying the spread spectrum clock generator(SSCG) with 3 % down spreading method to the camera control clock.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.7C
• /
• pp.696-705
• /
• 2005

The rapid progress of the software has enabled individuals to copy and remake digital contents, which was only done by professionals. However, this rapid growth of software has brought many other defects. As a solution to the problems, contents producer needs to have certification and inspection of its contents text and hold the proprietary rights. In this paper, the new video watermarking scheme is proposed which is appropriate for the requirements mentioned for digital video contents and it is applied to MPEG-2 video encoder and decoder. In order to insert watermark sequence for digital video data, watermarking used blocks reordering algorithm and SCL(secret code list). It is satisfied two properties of cryptography that confidentiality and integrity. We test the proposed algorithm to see its performance in terms of watermark capacity, compression robustness and visual quality impact. According to the experiment of proposed watermarking algorithm, we obtained satisfactory results that watermark can still be extracted after MPEG-2 re-encoding at lower bit rates. It is important property for data hiding and user authentication in video data.