• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.286-291
• /
• 2011

Directional couplers are widely used in RF and microwave applications to distribute or monitor signals. This paper presented a new structure of microstrip branch line directional coupler with coupled lines. The loose couplings of microstrip branch line directional couplers are impractical for the high characteristic impedance values required for the shunt branches. To overcome this limitation, the parallel coupled lines with the shorts were used for the high characteristic impedance. The results of the simulations and measurements were presented for the proposed branch line directional coupler. Measurement of the 10 dB branch line directional coupler shows that the return loss is higher than 30 dB over 10 % bandwidth and the isolation is 35 dB or better over 8 % bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.673-679
• /
• 2009

This paper proposes a resonance power-combining technique using CRLH-transmission line. The circuits using proposed technique consist of the parallel capacitances and transmission lines to satisfy matching conditions and to combine power of amplifiers. The CRLH(Composite Right/Lefi-Handed) transmission lines are used to reduce the circuit size. As a result, the power combining amplifier using proposed techniques is measured that a gain is equal and the output power is increased about 2.2 dB higher than the single amplifier. Also, a size of amplifier is 78.3 % smaller than the conventional amplifier using RH transmission line.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.7
• /
• pp.653-660
• /
• 2004

This paper presents monopole antenna with electromagnetically coupled feed and its equivalent circuit model. The proposed structure is consists of a rectangular disk-loaded monopole and a probe with rectangular spiral strip line feed. The rectangular disk-loaded monopole is represented by parallel RLC resonant circuit and the probe with rectangular spiral strip line feed is represented by series RLC resonant circuit. Therefore broad bandwidth can be achieved through electromagnetic coupling between these structures that generate two resonances within close frequency range. The antenna with electrical dimensions of only 0.075λ$\sub$0/${\times}$0.075λ$\sub$0/${\times}$0.075λ$\sub$0/ has 16.5 % fractional bandwidth for VSWR$\leq$2 at a center frequency of 2.038GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.10
• /
• pp.1122-1128
• /
• 2008

A novel tunable bandstop filter was proposed. It is composed of a right-handed transmission line, which has lowpass characteristics, and a left-handed transmission line which has highpass characteristics. Dispersion relations for the unit cells of RHTL and LHTL were derived by the method of ABCD parameter analysis. Varactor diodes and chip inductors were used to make the unit cells of RHTL and LHTL. A tunable bandstop filter was designed and fabricated by the parallel connection of RHTL and LHTL. The measured results of the proposed tunable bandstop filter are agreed well with the simulated results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.486-493
• /
• 2010

This article introduces a novel ultra wideband(UWB) bandpass filter(BPF) with sharp roll-off characteristics in stripline structure. The UWB characteristic is basically obtained from capacitive coupled cross resonator. The resonator has ${\lambda}/2$ length. And at the center of the resonator, two stubs are loaded, one is a ${\lambda}/8$ short-circuited stub and the other is a ${\lambda}/8$ open-circuited stub. The two stubs provide two attenuation poles at lower and upper cutoff frequencies. For input and output lines, two identical capacitively coupled lines have been installed to suppress the unwanted signals in the lower and upper stopbands. The filter has been designed for the U.S. UWB band(3.1~10.6 GHz) with two transmission zeros at 2.4 and 11.1 GHz. The filter has been realized with Low Temperature Core-fired Ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results. Insertion loss less than 0.7 dB and return loss better than 14 dB in the pass band have been measured. The group delay in the center frequency is 0.27 ns and the group delay variation within pass band is less than 0.5 ns. The size of the filter is $6{\times}18{\times}0.6\;mm^3$.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.320-322
• /
• 2001

본 논문에서는 전압 sag보상을 하기 위한 DSTATCOM 제어기를 설계하고 EMTDC/PSCAD로 확인하였다. DSTATCOM의 전류성분을 d,q분해 해석을 통하여 상태방정식을 유도하고 부하모델과 네트워크의 제약조건을 결합 모델을 제시하였다. 1선 지락 사고시 PI 제어시보다 LQR 제어의 응답 특성이 우수함을 검증하고 전압 sag가 개선됨을 보였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.7
• /
• pp.1237-1242
• /
• 2016

In this paper, the low pass filter with harmonics suppression and rejection using parallel coupled-line and radial type open stub is presented. And the resultant characteristic of the proposed low pass filter is that the harmonics are suppressed and rejected in wide bandwidth due to the parallel coupled-line structure. The open stub of a low pass filter is constructed in radial type which can be used to adjust the size of filter. The size of the proposed low pass filter is $6.98{\times}7.60mm2$ and the cut off frequency is 2.45 GHz. And the filter is economical in unit cost and can be constructed easily and has the merit of mass product because the filter is composed of distributed element. Also, the widely rejected harmonics is 128 % in the bandwidth and the insertion and return losses of the low pass filter are 1.07 dB and 19.5 dB, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7A
• /
• pp.947-954
• /
• 1999

A new low phase noise Dielectric Resonator Parallel Feedback Oscillator(DRPFO) that is proposed in this paper has a simple structure so that it can be fabricated in low cost and with high performance. The proposed DRPFO is in a feedback loop oscillator configuration, which is composed of a low noise amplifier, a power amplifier, a power attenuator, a power divider and a parallel resonator feedback element that consists of a dielectric resonator coupled with two microstrip lines. The measured phase noise of DRPFO was less than -81 dBc/Hz at offset frequency 1 kHz of 10.75 GHz carrier frequency, and the frequency stability of DRPFO was less than $\pm$200 kHz over the temperature range of -40$^{\circ}$C to +60$^{\circ}$C.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.1
• /
• pp.17-24
• /
• 2014

In this paper, we analysed coupling coefficient between dielectric resonator of high dielectric constant and microstrip line to design for low phase noise dielectric resonator by direct coupling. Also we analysed phase noise of dielectric resonance oscillator with parallel feedback circuit to complement Q by high dielectric constant. We obtained a result from high-stability dielectric oscillator which is optimum designed through analysis of dielectric resonance oscillator phase noise and coupling coefficient. The result is that the phase noise was -83.3dBc/Hz@1KHz at 20.25GHz when we used about 3.6 coupling coefficient and ${\epsilon}_r$=30 dielectric resonator of 20.25GHz dielectric resonance oscillator. As a result, we suggested the direct-connect design method by frequency multiplication mode to prevent phase noise loss at K-Band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.12
• /
• pp.115-124
• /
• 2004

In this paper, we introduce the advanced compact transmission line with periodic stepped stubs. They are more effective than normal stubs in ATL. The short stepped stubs loading of transmission line work as effective shunt capacitance and that was proved by equivalent circuit based on transmission line theory and quasi-static analysis. And the compact branch-line coupler and the compact rat-race coupler via proposed compact microstrip line were designed at 1.8 ㎓. They have 677 ㎟ and 913 ㎟, respectively, and they are 62% and 45% of normal design.