• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.5
• /
• pp.86-96
• /
• 1997

In this paper, engine-CVT consolidated control algorithm was developed. Engine -CVT control strategy suggested uses throttle control based on power difference and CVT ratio control based in CVT ratio map. Simulation results showed that the larger the rate of CVT ratio, the better the engine performance in the optimal operation line. Also, it was found that the engine performance where the magnitude of the acceleration changes abruptly depends on the magnitude of the rate of CVT ratio. Comparing the results of CVT control only without engine control, the engine-CVT control algorithm suggested in this work showed better performance demonstrating that the consolidated control algorithm should be required for the engine optimal operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.95-104
• /
• 1997

We consider controller design problem to enhance shift quality for automatic transmission. A dynamic modeling related to shifting (mainly 2-3 up-shift) is constructed and nonlinear robust controllers are designed to reduce output torque during shifting. Suggesting a new hydraulic circuit enabling the direct clutch drive, the control activity is extended and more implementable than the conventional design. The designed robust controllers overcome the unmodeled dynamics and the uncertainty embending in the system. Moreover, the dynamic effect between the clutch pressure and the PWM valve duty is considered via singular perturbation technique.

• Journal of Biosystems Engineering
• /
• v.18 no.4
• /
• pp.305-316
• /
• 1993

Fuel efficiency in tractor operations dep6nds on the selection of transmission gears and upon the engine being operated at or near maximum torque much of time. The objective of this study was to develop automatic control systems for tractor transmission ratio and governor setting so that the engine is operated at or near maximum torque as much of time as possible. An indoor test unit, which can be used to simulate tractor operation, was built in order to investigate the system design parameters and test the performance of the control system designed. The test-unit consists of engine, gear-type transmission, dynamometer, and control systems for transmission ratio and engine speed. Governor setting lever was controlled by a step motor, and the clutch and transmission levers were controlled by hydraulic cylinders and solenoid valves. The control systems showed good time responses which are assumed to be suitable for optimal tractor operation. The time required for shifting gears from clutch disengagement to engagement was about 1 second, which is almost the same as that for manual shift. And the settling time for engine speed control system was about 5 to 6 seconds.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.49-58
• /
• 1997

In this paper, a transfer function was obtained for a PWM high speed solenoid valve controlled metal belt CVT system. The transfer function was defined as the ratio of speed ratio to PWM duty ratio and derived in time domain by linear regression analysis from the experimental results. The transfer function obtained showed different dynamic characteristics for the up and down shift. Also, LQG/LTR controller was designed for the CVT system using the transfer function. It is seen from the experimental results that LQG/LTR control showed good performance for the speed ratio tracking and disturbance rejection. The phase difference and relatively slow response are considered due to the inaccuracy os the transfer functions, which resulted from the inherent nonlinearities of the transmission characteristics of the metal belt CVT.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.30-38
• /
• 1991

자동차의 제동장치, 조향장치, 자동 변속장치 등에 요구되는 큰 힘을 얻기 위하여 유압식 구동장치가 중량당 출력비가 높고 응답특성이 좋으며 과부하에 대한 방지기능이 간단하게 이루어 진다는 장점이 있기 때문이다. 본 고에서는 우리나라에서도 전자제어식 제동장치, 조향장치, 자동변속장치, 현가장치 등의 개발을 시도하고 있는 현 시점에서 기술축적이 가장 취약한 분야라고 볼 수 있는 자동차용 전기유압밸브의 기본적인 메카니즘에 대하여 종합적으로 소개하고자 한다.

• Journal of the Korean Institute of Gas
• /
• v.28 no.1
• /
• pp.59-64
• /
• 2024

In this study, we conducted research on a miniaturized transmission system suitable for ultra-compact electric vehicles, such as electric arts or small electric cars. While conventional electric vehicles eliminate multi-gear transmissions and control motor output or secure initial driving force through reducers, in vehicles like electric karts or compact electric cars, which have relatively small battery capacities, the driving range can be reduced or the motor can be stressed epending on the loading state. Therefore, in this study, we developed a low stage ratio 0.625 and high stage ratio 1.6 a two-stage transmission system that can change gears as needed, considering factors such as slope conditions and loading status, by applying the continuously variable transmission (CVT) mechanism. Based on the selected gear ratios, we designed the transmission and created a test rig to verify the power transmission efficiency of the developed transmission. Using the test rig, we varied the rotational speed and load of the transmission to confirm its power transmission characteristics and also examined the heat generation characteristics during shifting and operation. As a result, developed a two-stage transmission with a CVT structure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.255-264
• /
• 2002

In this paper, the power transmitting mechanism for negative torque of the metal V-belt (MVB) CVT were investigated by theoretically analyzing variation of band tension, block compression forces for each of the primary and secondary pulleys. An experimental study was performed to investigate the speed ratio - thrust characteristics for negative torque. The experimental results are in good acoordance with the theoretical results. CVT line pressure control logic was suggested for negative torque based the speed radio - negative torque - thrust characteristics and the thrust ratio curves. The results of this study can be used as basic design materials for developing the CVT control system for negative torque.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.114-121
• /
• 2002

This paper describes the control system of the toroidal traction driver continuously variable-speed transmission(CVT) fur a tractor. The instrumentation system, the hydraulic power control system and the principle control scheme were introduced. Experimental tests in the bench and the tractor were conducted to validate the performance of the CVT utilizing the proposed controller. The speed of the vehicle was continuously changed to follow the speed set by driver under various operating conditions. Given the reduction ratio of the variator from 2.0 to 1.0, the settling time was about just 0.52 seconds which was satisfactory value for working with the tractor. It was also proved that the tractor could work with continuously variable speed under heavy load disturbances.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.111-119
• /
• 1997

In this paper, engine-CVT consolidated control performance were investigated experimentally. Engine-CVT consolidated control was composed of engine throttle control based on power difference and CVT ratio control based on CVT ratio map. Experimental results showed that engine optimal operation was obtained while satisfying the driver's desire, i. e., following the given drive mode by engine-CVT consolidated control. Also, it was found that engine performance is subjected to inertia of the powertrain where the magnitude of acceleration changes abruptyly. Comparing with the results of CVT only control, the results of engine-CVT consolidated control showed better performance. Therefore, in order to meet the driver's desire as well as keeping the engine optimal operation, the engine-CVT consolidated control could be suggested as an integral solution.