• 대한기계학회논문집B
• /
• 제25권1호
• /
• pp.18-28
• /
• 2001

The present study investigates flow dynamics between two dimensional compliant plates under sinusoidal flow conditions in order to understand influence of wall motion, impedance phase angle (time delay between pressure and flow waveforms), and non-Newtonian fluid on wall shear stress using computational fluid dynamics. The results showed that wall motion induced additional terms in the streamwise velocity profile and the pressure gradient. These additional terms due to wall motion reduced the amplitude of wall shear stress and also changed the mean wall shear stress. The trend of the changes was very different depending on the impedance phase angle. As the impedance phase angle was changed to more negative values, the mean wall shear stress decreased while the amplitude of wall shear stress increased. As the phase angle was reduced from 0°to -90°under $\pm$4% wall motion, the mean wall shear stress decreased by 12% and the amplitude of wall shear stress increased by 9%. Therefore, for hypertensive patients who have large negative phase angles, the ratio of amplitude and mean of the wall shear stress is raised resulting in a more vulnerable state to atherosclerosis according to the low and oscillatory shear stress theory. We also found that non-Newtonian characteristics of the blood protect atherosclerosis by decreasing the oscillatory shear index.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권1호
• /
• pp.131-138
• /
• 2001

In this paper, an experimental investigation of characteristics of developing turbulent steady flows in a square-sectional $180^{\circ}$curved duct is presented. The experimental study using air in a square-sectional $180^{\circ}$ curved duct carryed out to measure axials direction velocity and wall shear stress distrbutions by using Laser Dopper Velocimeter(LDV) system with data acquistion and processing the system of FIND6260 softwere at 7 sections from the inlet($\phi=0^{\circ}$) to the outlet($\phi=180^{\circ}$) in $301^{\circ}$ intervals of a curved duct.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.219-222
• /
• 2001

The objective of the present study is to evaluate the effects of the stenting shapes on flow velocity and wall shear stress in angulated coronary stenosis by computer simulation. Coronary angiogram and Doppler ultrasound measurement in the patients with angulated coronary stenosis were obtained. Inlet wave velocity distribution obtained from in vivo intracoronary Doppler data was used for the numerical simulation. Spatial pattern of blood flow velocity and recirculation area were drawn through out the selected segment of coronary models. Wall shear stresses in the intracoronary stent models were calculated from three-dimensional computer simulation. A negative shear stress region, which is consistent with re-circulation area on flow pattern, was noted on the inner wall of post-stenotic area of pre-stenting model. The negative shear stress was disappeared after stenting. Shear stress in the post-stenting model was markedly reduced up to about two orders of magnitude compared to that of the pre-stenting model.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권2호
• /
• pp.136-143
• /
• 1997

직경 비가 0.56인 이중동심관에 내외측모두 매끈한 벽면, 벽면 거칠기를 안측, 외측, 그리고 양측 모두의 4경우에 대한 난류 유동과 열전달특성을 실험과 이론으로 연구하였다. 시간평균속도분포, 마찰계수, 그리고 최대 속도 지점과 전단응력이 0인 지점들을 피토튜브와 X형 열선 풍속계로 측정하였다. 이중동심관내에서 4가지 경우에 따른 사각돌출형 거칠기효과가 난류 유동과 열전달에 미치는 영향을 수정난류모델을 기초로 하여 연구하였다. 직경비, 거칠기 위치, 레이놀즈수, 그리고 프란틀수 등의 여러 변수에 의해서 난류 유동과 열전달을 고찰하였다. 본 연구는 전체적 효율 측면에서 유리하게 열전달율을 향상시킬수 있는 거칠기 구조를 밝혔다.

• 대한기계학회논문집B
• /
• 제37권10호
• /
• pp.927-932
• /
• 2013

뇌동맥류모델은 CT 영상을 기반으로 추출하여, ANSYS-FLUENT를 사용해 전산 유체유동해석을 수행하였다. 본 연구를 통해 뇌동맥류에서 최소 벽전단응력은 동맥류가 발생한 영역에서 일어나는 것을 알 수 있다. 또한 뇌동맥류 모델에서 우측중뇌동맥 안쪽벽면에 작용하는 벽전단응력의 크기는 동맥류 전부와 후부의 벽면에 작용하는 벽전단응력의 크기에 비해 20 배 더 크게 발생하는 것을 알 수 있다. 그러나 동맥류 영역에서의 전단응력의 크기는 매우 작게 나타났다. 혈관 수축이 일어나는 동안 동맥류의 영역에서 매우 복잡한 이차유동이 발생하는 것을 볼 수 있다. 동맥류 내부에서의 혈류유동은 나선형 유동형태를 보이며, 본 연구의 혈류역학적 특성 분석을 통해 뇌동맥류의 파열을 예견할 수 있을 것으로 판단한다.

• 대한기계학회논문집B
• /
• 제36권8호
• /
• pp.829-837
• /
• 2012

벽면 난류의 항력과 밀접한 관련이 있는 유동구조를 조사하기 위해 $Re_{\tau}$ = 180, 395, 590 의 난류채널유동에 대한 직접수치모사를 수행하였다. 확률밀도함수를 조사하여 레이놀즈 전단응력에 가장 큰 기여를 하는 Q2 이벤트를 파악하였으며 Q2 이벤트의 각도의 변화가 $y^+<50$ 에서는 벽 단위로 스케일링되며, y/h > 0.5 에서는 채널의 높이로 스케일링 됨을 확인하였다. Q2 이벤트를 조건으로 하는 조건부 평균 유동장을 조사하여 레이놀즈 전단응력의 발생과 관련이 있는 유동구조는 주 유동방향의 보텍스 및 헤어핀 형상의 보텍스임을 보였다. 또한, 순간 유동장을 관찰하여 높은 레이놀즈 전단 응력의 분포가 이러한 보텍스 구조와 관련이 있으며 1.5 ~ 3h 의 크기를 갖는 대형유동구조를 구성함을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.933-934
• /
• 2012

• 대한기계학회논문집
• /
• 제18권7호
• /
• pp.1873-1880
• /
• 1994

Fully developed turbulent flow in a circular pipe and laminar boundary layer on a flat plate were measured to develop a measuring technique of the wall sheat stress using Preston tubes. New empirical formulas to extimate displacement factor of Preston tube obtained through the present study. The displacement factor for turbulent flow was considerably different from that for the laminar flow. Measured wall shear stress was not pretty dependent on the displacement factor for Preston tubes in the inertia sublayer of turbulent boundary layer, however was considerably affected in the laminar boundary layer. Measuring error of skin friction using the CPM technique was 3% for turbulent and 5% for thin laminar boundary layers.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.560-565
• /
• 2001

The objective of the present study is to investigate the characteristics for flow and wall shear stress in the aneurysm which is a local dilatation of the blood vessel. The numerical simulation using the commercial software for the laminar and steady flow were carried out over the diameter ratios(ratio of maximum diameter of aneurysm to the diameter of blood vessel) ranging from 1.5 to 2.5 and Reynolds number ranging from 900 to 1800. It was shown that a recirculating vortex occupied the entire bulge with its core located closer to the distal end of the bulge and the strength of vortex increased with increase of the Reynolds number and diameter ratio. Especially, for the Reynolds number of 1800 and diameter ratio of 2.5, the very weak secondary recirculating flow was produced at the left upper of the aneurysm. The position of a maximum wall shear stress was the distal end of the aneurysm(z=18mm) regardless of the Reynolds number and diameter ratios. But the maximum values of the wall shear stress increased in proportion to the increase of Reynolds number and diameter ratio.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.318-323
• /
• 2001

Characteristics of the pulsatile flow in a 3-dimensional elastic blood vessel are investigated to understand the blood flow phenomena in the human body arteries. In this study, a model for the elastic blood vessel is proposed. The finite volume prediction is used to analyse the pulsatile flow in the elastic blood vessel. Variations of the pressure, velocity and wall shear stress of the pulsatile flow in the elastic blood vessel are obtained. The magnitudes of the velocity waveforms in the elastic blood vessel model are larger than those in the rigid blood vessel model. The wall shear stresses on the elastic vessel vary with the blood vessel motions. Amplitude indices of the wall shear stress for blood in the elastic blood vessel are $4\sim5$ times larger than those of the Newtonian fluid. As the phase angle increased, point of the phase angle is are moved forward and the wall shear stresses are increased for blood and the Newtonian fluid.