• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.10
• /
• pp.681-687
• /
• 2016

It is essential for micro jet injectors in the biomedical sector to operate under high pressure. High pressure injection, however, is accompanied by high volumes. On/Off valves that can be operated at high speeds have been used to address this problem. In this research, piezoelectric actuators which have a response frequency of the order of hundreds of kilohertz were used as the On/Off valve and experiments were applied. Researchers developed a controller to precisely manipulate the piezoelectric valve with various waveforms. They also fabricated five types of nozzles to consider the effect of nozzle type on injection. This allowed researchers to manipulate and confirm factors that can affect the injection volume and force. Results of this experiment have shown how to decrease the injection volume and increase the injection force. and it is predicted that the optimized injection volume and force value can be determined depending on the skin type.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.93-100
• /
• 2009

Intake/exhaust valve timing and exhaust cam lift were changed to control the internal exhaust gas recirculation (IEGR) and combustion phase of homogeneous charge compression ignition (HCCI) engine. To measure the IEGR rate, in-cylinder gas was sampled during from intake valve close to before ignition start. The lower exhaust cam made shorter valve event than higher exhaust cam and made IEGR increase because of trapping the exhaust gas. IEGR rate was more affected by exhaust valve timing than intake valve timing and increased as exhaust valve timing advanced. In-cylinder pressure was increased near top dead center due to early close of exhaust valve. Ignition timing was more affected by intake valve timing than exhaust valve timing in case of exhaust valve lift 8.4 mm, while ignition timing was affected by both intake and exhaust valve timing in case of exhaust valve 2.5 mm. Burn duration with exhaust valve lift 2.5 mm was longer than other case due to higher IEGR rate. The fuel conversion efficiency with higher exhaust valve lift was higher than that with lower exhaust valve lift. The late exhaust and intake maximum open point (MOP) made the fuel conversion efficiency improve.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.526-529
• /
• 2009

In this study, we analyze the characteristic of burning classified by a propellant according to a flux of an oxidizer to analyze propellant regression distance in accordance with a thrust control and burning time of hybrid rocket using hybrid combustor of Lab-Scale. To control a flux of an oxidizer, we design flow control system to regulate the mount of opening and shutting of a needle valve by a driving of stepping motor by a combination the needle valve with stepping motor. We derive the relationships between mass flow rate and regression rate according to a propellant through the oxidizer flux change. While doing the thrust control, we estimate regression distance through the oxidizer flux in accordance with thrust and confirm the creditability through the actual thrust control burning experimentation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.40-47
• /
• 2010

In this study, basic research on the thrust control by controling oxidizer mass flow rate of a $GO_2$/PE hybrid rocket is presented. For this purpose, hybrid rocket system including oxidizer flow control system and data acquisition system was developed. To control oxidizer mass flow rate, we used needle valve with stepping motor which was controled by LabVIEW program. During the fundamental experiments, this system managed to follow the pre-programmed (20 N - 10 N - 20 N - 0 N) thrust level.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.4
• /
• pp.76-80
• /
• 2014

PFA fluoropolymer lined technology revolutionized ball valve development and design decades ago and continues to be pivotal for many products and valve solutions in diverse industries and applications, such as chemical process, semiconductor/LCD manufacturing processes, pharmaceutical and others. Because of the extreme operating conditions such as high-temperature (${\sim}120^{\circ}C$) and high-pressure (~10 bar), the reliability of the valve is very important for minimizing in-line leakage and fugitive emissions of strong corrosive chemicals (hydrochloric acid, hydrofluoric acid, nitric acid, etc.) transported through the lines. In this study, we investigated the flow characteristics with flow coefficient in a PFA lined ball valve for different opening degrees using CFD analyses. The results should be the guidance for a new PFA lined ball valve design that will incorporate all the acclaimed and demonstrated benefits of the current design approaches.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.5
• /
• pp.45-50
• /
• 2011

Compression pressure of individual cylinder and valve timing have big influence on combustion pressure, indicated mean effective pressure (IMEP), emission, vibration, combustion noise and many other combustion parameters. Conventional method, however, to check compression pressure uniformity is done by mechanical pressure gage and valve timing is checked manually. This conventional method causes inaccuracy of cylinder pressure measurement because of different cranking speed results from battery status and temperature. Also to check valve timing, related FEAD parts should be disassembled and timing mark should be checked. This study describes and suggests new methodology to measure compression pressure by analysis of start motor current and to check valve timing by cylinder pressure with high accuracy. Results, it is found that detection of bulky as well as small leaky cylinder is possible by cranking motor current analysis and wrong valve timing can be detected by cylinder pressure analysis and cam and crank sensor signal.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.535-539
• /
• 2010

We present a digital dilution chip comprising a $2{\times}6$ array of wells; the chip can be employed to change the dilution ratio as well as to initiate reactions among diluted samples by using the inter-well valve around the well. In previous dilution devices, streams comprising sample and dilution solutions were merged and separated by a branched microchannel. Therefore, the dilution ratio could not be changed until the structure of the branched microchannel was changed. The present device merges and splits the wells filled with sample or dilution solution by controlling inter-well valves around the wells. Thus, it is possible to change the dilution ratio by changing the sequence in which merging and splitting sequence of each well filled with sample or dilution solution. In experiments, we found that the chip could be used to change linear or exponential dilution ratios within an error of 16.7% and to initiate reactions among the samples within a reaction error of 17.7%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.7-13
• /
• 2010

To satisfy the needs on fuel economy and engine performance, continuous variable valve lift systems are applying to engines. In the CVVL system, fuel economy can be improved by reducing pumping loss during the induction process, and engine performance can be also improved by controlling volumetric efficiency and the residual gas fraction. Because the residual gas fraction directly affects volumetric efficiency, engine performance, combustion efficiency and emissions in SI engines, controlling residual gas fraction is one of the important things in engine development process. This analysis investigates the residual gas fraction and volumetric efficiency with changes of intake valve lifts and intake valve timings. In this study, unsteady state solutions were solved during exhaust and induction processes. Results show variation of the residual gas fraction and volumetric efficiency by changing intake valve timing and lift. Decreasing intake valve lift leads to increase the residual gas fraction and to decrease volumetric efficiency.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.388-392
• /
• 2007

지구온단화와 이상기후에 의해 시설물 피해가 나날이 증가하고 있으며, 농촌의 인구감소 및 고령화에 의해 이러한 집중강우등에 대한 대처도 어려운 실정이다. 현재 전국에서 농업용수 공급을 위해 사용하고 있는 농업용 저수지는 17,882개소로서 이 중 축조한지가 35년 이상 경과된 저수지가 15,856개소로서 88.7%나 차지하고 있다. 이러한 현상은 저수지를 구성하고 있는 각종 부대시설의 노후화로 귀결되며 농업용수의 낭비 및 효율적인 운영을 위해서는 시설의 현대화가 필수적이라고 할 수 있다. 따라서 본 연구에서는 저수지에서 물을 직접 공급하는 시설인 사통수문을 대상으로 현대화를 이룩하고 또한 사용동력도 대체에너지를 이용하기 위한 방안을 제시하였다. 사통수문의 수문비는 수중의 압력을 효율적으로 분산시킬 수 있는 원형수문비와 수중에서도 사용동력을 가장 적게 할 수 있는 밸브형을 기준으로 개발을 하였으며, 수문비와 구동부를 연결하는 작동 롯드의 힘전달을 최소화하기 위하여 유니버셜 쪼인트를 볼밸브형으로 개발하였다. 이에 따라서 작동용 롯드의 길이가 길어져도 수문비에 걸리는 작동모멘트를 최소화하여 태양광을 이용한 동력사용이 가능해졌다. 특히 수중에서 움직이는 특성을 감안하여 원형 수문비의 경우에는 수문비와 수문틀 사이에 마찰력을 감소시키기 위하여 수문틀측을 약간 경사지게 가공을 하고 중간에 볼 베이렁을 부착시켜 수문개폐가 원활토록 지수부의 구조변화를 하였다. 또한 농업용수공급시 수류와 함께 유입되는 저수지 내 오물을 차단하기 위하여 수문의 전면에 스크린을 설치하였으며 토사퇴적으로 인하여 수문작동의 방해가 되지 않도록 하기 위하여 토목구조물을 설치하였다. 그리고 동력전달을 효율적으로 하기 위하여 Solar Unit으로부터 나오는 전기를 중전기에서 밧데리로 축전을 시키고 완전 충전 후에는 나머지 전기는 방전이 되도록 회로를 구성하였다. 사통수문 자원조사 결과에 의하면 현재 저수지에 물공급을 하는 수문은 취수탑 형식이 70% 이상을 차지하고 있으며 나머지 30%의 사통수문 중 원형수문비가 98% 이상을 차지하고 있다. 현재 대체에너지를 사용하는 저수지 사통수문은 없는 것으로 조사되었으며 전력을 사용하는 사통도 조사결과에 의하면 20% 이내로 나타났다. 이러한 결과는 향후 수리시설 개보수시 적은 예산으로 사업을 시행하는 경우 사통수문의 설치방향의 지표가 될 것으로 판단되며 수리시설의 운영관리에 대한 새로운 대안으로 제시할 수 있다.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.1-8
• /
• 2018

FCV is installed with a automatic valve attached in an high pressure cylinder to control the hydrogen flow. The supply of hydrogen from the cylinder into the fuel cell stack is controlled via the on/off operation of a solenoid attached to the automatic valve. The solenoid needs to provide the necessary attraction force even at any saturation temperature caused by drive of the vehicle. In this study, the simplified prediction equations for the saturation temperature are suggested. The finite element analysis was performed by steady state technique, according to the boundary condition in order to predict the saturation temperature and attraction force. Finally, the saturation temperature was validated through comparison between the analysis results and measurement results. From the results, the measured saturation temperature $5.9^{\circ}C$ lower with respect to the analysis results. And the error of attraction force ranged from 1.0 to 2.1 N at testing conditions.