• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.904-909
• /
• 2019

Using the ion-beam irradiated indium zinc oxide (IZO) films which was cured at $100^{\circ}C$, uniform LC and homogeneous alignment of liquid crystal (LC) molecules was achieved. The IZO film was deposited on the glass substrate at the curing temperature of $100^{\circ}C$ and irradiated by the ion-beam which is an LC alignment method. To verify the LC alignment characteristics, polarizing optical microscope and the crystal rotation method were used. Additionally, it was confirmed that the LC cell with the IZO films had an enough thermal budget for high-quality LC applications. Field emission scanning electron microscope was conducted as a surface analysis to evaluate the effect of the ion-beam irradiation on the IZO films. Through this, it was revealed that the ion-beam irradiation induced rough surface with anisotropic characteristics. Finally, electro-optical (EO) performances of the twisted-nematic cells with the IZO films were collected and it was confirmed that this cell had better EO performances than the conventional rubbed polyimide. Furthermore, the polar anchoring energy was measured and a suitable value for stable LC device operation was achieved.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.1
• /
• pp.72-77
• /
• 2019

The display that provides information to us through the visual sense is a very important information transmission means by intuitively transmitting information, and the liquid crystal display (LCD) is the most widely used information transmission display. In this paper, we studied solvent assisted micromolding as an alternative for the rubbing that is essential to align the liquid crystals in LCD and successfully aligned the liquid crystal molecules by constructing the nanostructures on conventional polyimide alignment layer. When generating the nanostructures on the polyimide film, there was a competitive correlation between the dissolution effect of the polymer by the solvent and the capillary effect of the polyimide molecules into the nanostructures of the mold depending on the process temperature. It was possible to form nanostructures with high step by deriving the optimum temperature. These nanostructures were able to align the liquid crystal molecules uniformly and demonstrated that they could form a desirable pretilt angle.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.64-68
• /
• 2021

We demonstrate an effect of annealing temperature on imprinting process of BiLaO thin film for liquid crystal alignment. BiLaO prepared sol-gel process was deposited by spin coating on a glass substrate, and then transferred to a pre-fabricated aligned pattern which is fabricated on a silicon wafer by laser interference lithography. Thin film was annealed at different temperature of 100, 150, 200, and 250 ℃. From the polarized optical microscopy analysis, the liquid crystal orientation was not uniform at the annealing temperature of 200 ℃ or lower and the uniform liquid crystal alignment characteristics were confirmed at the annealing temperature of 250 ℃. From atomic force microscopy, the pattern was not transferred at a temperature of 200 ℃ or lower. In contrast, the pattern was transferred at 250 ℃. Anisotropy of the thin film was obtained by the alignment pattern transferred at a temperature of 250 ℃, and the liquid crystal molecules could be evenly oriented on the thin film. Therefore, it was confirmed that the liquid crystal alignment process by the imprinting process of the BiLaO oxide film was affected by the annealing temperature.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.2
• /
• pp.109-115
• /
• 2023

In this paper, we demonstrated the orientation characteristics of liquid crystals using UV-treated FSAM as alignment layer. Moreover we confirmed the FSAM properties before and after UV treatment on indium tin oxide (ITO) glass substrates using physicochemical analysis. The hydrophobic property of the FSAM surface is change to hydrophilic through UV treatment. After UV treatment the LC molecules also were uniformly and horizontally aligned on the FSAM surfaces and the pretilt angle was obviously changed 90° degrees to 0° degrees. EO characteristic of TN cell which was fabricated with UV-treated FSAM was faster response time compare to conventional PI layer. The FSAM before and after UV treatment has a superior application potential as the LC alignment layer for LCD, potentially replacing the conventional polyimide layer.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.2
• /
• pp.1-41
• /
• 1988

For the purpose of utilizing the sawdust having poor combining properties as board raw material and resulting in dimensional instability of board, polypropylene chip (abbreviated below as PP chip) or oriented PP thread was combined with sawdust particle from white meranti(Shorea sp.). The PP chip was prepared from PP thread in length of 0.25, 0.5, 1.0 and 1.5 cm for conventional blending application. Thereafter, the PP chip cut as above was combined with the sawdust particle by 3, 6, 9, 12 and 15% on the weight basis of board. Oriented PP threads were aligned with spacing of 0.5, 1.0 and 1.5cm along transverse direction of board. The physical and mechanical properties on one, two and three layer boards manufactured with the above combining conditions were investigated. The conclusions obtained at this study were summarized as follows: 1. In thickness swelling, all one layer boards combined with PP chips showed lower values than control sawdustboard, and gradually clear decreasing tendendy with the increase of PP chip composition. Two layer board showed higher swelling value than one layer board, but the majority of boards lower values than control sawdustboard. All three layer boards showed lower swelling values than control sawdustboard. 2. In the PP chip and oriented thread combining board, the swelling values of boards combining 0.5cm spacing oriented thread with 1.0 or 1.5cm long PP chip in 12 and 15% by board weight were much lower than the lowest of one or three layer. 3. In specific gravity of 0.51, modulus of rupture of one layer board combined with 3% PP chip showed higher value than control sawdustboard. However, moduli of rupture of the boards with every PP chip composition did not exceed 80kgf/cm2, the low limit value of type 100 board, Korean Industrial Standard KS F 3104 Particleboards. Moduli of rupture of 6%, 1.5cm-long and 3% PP chip combined boards in specific gravity of 0.63 as well as PP chip combined board in specific gravity of 0.72 exceeded 80kgf/$cm^2$ on KS F 3104. Two layer boards combined with every PI' chip composition showed lower values than control sawdustboard and one layer board. Three layer boards combined with.1.5cm long PP chip in 3, 6 and 9% combination level showed higher values than control sawdustboard, and exceeded 80kgf/$cm^2$ on KS F 3104. 4. In modulus of rupture of PP thread oriented sawdustboard, 0.5cm spacing oriented board showed the highest value, and 1.0 and 1.5cm spacing oriented boards lower values than the 0.5cm. However, all PP thread oriented sawdustboards showed higher values than control saw-dustboard. 5. Moduli of rupture in the majority of PP chip and oriented thread combining boards were higher than 80kgf/$cm^2$ on KS F 3104. Moduli of rupture in the boards combining longer PP chip with narrower 0.5cm spacing oriented thread showed high values. In accordance with the spacing increase of oriented thread, moduli of rupture in the PP chip and oriented thread combining boards showed increasing tendency compared with oriented sawdustboard. 6. Moduli of elasticity in one, two and three layer boards were lower than those of control sawdustboard, however, moduli of elasticity of oriented sawdustboards with 0.5, 1.0 and 1.5cm spacing increased 20, 18 and 10% compared with control sawdustboard, respectively. 7. Moduli of elasticity in the majority of PP chip and oriented thread combining boards in 0.5, 1.0 and 1.5cm oriented spacing showed much higher values than control sawdustboard. On the whole, moduli of elasticity in the oriented boards combined with 9% or less combination level and 0.5cm or more length of PP chip showed higher values than oriented sawdustboard. The increasing effect on modulus of elasticity was shown by the PP chip composition in oriented board with narrow spacing. 8. Internal bond strengths of all one layer PP chip combined boards showed lower values than control sawdust board, however, the PP chip combined boards in specific gravity of 0.63 and 0.72 exceeded 1.5kgf/$cm^2$, the low limit value of type 100 board and 3kgf/$cm^2$, type 200 board on KS F 3104, respectively. And also most of all two, three layer-and oriented boards exceeded 3kgf/$cm^2$ on KS F. 9. In general, screw holding strength of one layer board combined with PP chip showed lower value than control sawdustboard, however, that of two or three layer board combined with PP chip did no decreased tendency, and even screw holding strength with the increase of PP chip composition. In the PP chip and oriented PP thread combining boards, most of the boards showed higher values than control sawdustboard in 9% or less PP chip composition.

• Electrical & Electronic Materials
• /
• v.3 no.1
• /
• pp.45-51
• /
• 1990

무배향 미연신 폴리에틸렌 테레프탈레이트 필름을 수중에서 일축연신 시킨후 연신된 시료의 열자극전류를 측정하여 검토 고찰하였다. 연신에 따른 측정결과 결정화도가 대체로 증가하는 경향이 있으나 연신비 150% 부근에서는 반대로 결정화도가 감소함을 알수가 있었는데 이는 초기인장에 따른 일시적 분자배향의 불안정한 형태로 인한 자유체적의 증가와 더불어 배위 엔트로피가 증가 하기 때문이라고 생각되며 인장된 시료의 밀도측정 및 적외선 스펙트럼분석으로 부터 확인하였다. 그리고 인장비의 변화에 따른 열자극전류의 피이크를 105(.deg.C)부근에서 얻었으며 인장비에 따른 열자극전류의 활성화 에너지를 구한 결과 150%에서 가장 큰 값을 얻었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.2
• /
• pp.110-114
• /
• 2002

The relationship between the orientation of molecules adsorbed on $_TiO2$ and their photoproducts was examined by employing HBPCA (4-hydroxy-biphenylcarboxylic acid) as a model organic pollutant. For this purpose, the Photoproducts after irradiation with UV radiation at various pH were compared by utilizing UV and Raman spectroscopies. It was found from these studies that pH affected the photoproducts probably due to the different orientations of the adsorbed molecules, and that the orientation of the adsorbed molecules and their photoproducts were closely correlated.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.12
• /
• pp.97-105
• /
• 1998

The fiber oriented condition inside fiber reinforced composite material is a basic factor of mechanical properties of composite materials. It is very important to meausure the fiber orientation angle for the determination of molding conditions, mechanical characteristics, and the design of composite materials. In the work, the fiber orientation distribution of simulation figure plotted by PC is measured using image processing in order to examine the accuracy of intersection counting method. The fiber orientation function measured by intersection counting method using image processing is compared with the calculated fiber orientation function. The results show that the measured value of fiber orientation function using intersection counting method is lower than the calculated value, because the number of intersection between the scanning line and the fiber with smaller fiber aspect ratio is counted less than with larger fiber aspect ratio.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.185-185
• /
• 2003

TiN 박막을 Ti 타겟을 이용하여 Si(001) 기판위에 반응성 RF 마그네트론 스퍼터 방법으로 제조하였다. 반응성 스퍼터링시 온도를 $600^{\circ}C$로 고정하고 $N_2$/Ar비, 공정압력, RF파워를 변화시키면서 박막을 제조하였고 각각의 공정조건에 따른 TiN 박막의 결정성 변화를 XRD, SEM, TEM, HRTEM을 이용하여 조사하였다. 그 결과 TiN 박막은 $N_2$/Ar비가 작을 경우 공정압력이 커짐에 따라 (001) 배향에서 (111) 배향으로 바뀜을 확인하였다. 또한 $N_2$/Ar비가 클 경우는 공정압력이 증가함에 따라(001) 우선 배향성이 향상됨을 확인하였다. 이런 결정성 변화가 전기적 특성에 미치는 영향에 관하여 논의할 것이다.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.3
• /
• pp.34-43
• /
• 1996

In this study basic equations of fiber orientations is cimpared with experimental results. It is found that fiber orientations of short fiber reinforced polymeric composite under compression molding are governed by slope of flow speed in x-y direction. Fiber orientation angle of mold is also found to increase with closure speed and the compression ratio. At the middle of the mold, the slope of flow speed is larger in x-direction than in y-direction. At the wall of the mold, the shope of flow speed in y-direction occurs due to the effect of friction, hence affects the fiber orientation. The effect of partial flow, which incurs y-direction orientation causes to increase the fiber orientation angle at the fore part of the flow.