• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.411-416
• /
• 2020

An optical arrangement has been set inside a photo-spectrometer to measure the reflectance of IR optics materials in mid IR range. The optical arrangement consists of equally spaced 4 gold coated full reflecting mirrors with the incidence angle of 45°. Baseline beam intensity I_B has been measured while the beam proceeds through the 4 mirrors. Reflectance of a mirror has been estimated from the I_B. And the beam intensity I_S with the specimen in the optical path has been measured with the 4th mirror replaced with the specimen. Reflectance of the specimen has been estimated from the value of I_S/I_B. Then the estimated reflectance has been put in Fresnel equation relating reflectance and refractive index(RI) to estimate the RI of the material. Measurement has been made for sapphire, germanium, magnesium fluoride, and zinc sulfide. The estimated RI of the materials are closely matching with reference data and the maximum difference less than 2% over the wavelength range 3-5㎛ for all materials tested. As an FT-IR photo-spectrometer with a broadband wavelength infrared light source is used, this method has the advantage of measuring the refractive index at multiple wavelengths in a single measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.549-555
• /
• 2005

This paper describes a microwave direction finding technology which is used for RF signal acquisition and monitoring systems. This paper suggests a direction finding method which use a combination of the amplitude-comparison technology and the phase-comparison technology. The amplitude-comparison technology uses the amplitude difference of the RF signals received from the array antennas of direction finding system and removes the ambiguity of wave incident bearing. The phase-comparison technology uses the phase difference of the RF signals received from the same nay antennas and makes a good direction finding accuracy. The suggested direction finding technology is designed to place 8 array antennas in a $45^{\circ}$ distance around the circle for $360^{\circ}$ azimuth angle. Also it is designed to use the phase difference of the received signals ken two nearby antennas to measure the signal incident direction accurately and to use the amplitude difference to remove the ambiguity of wave incident bearing. The simulation and measurement results are under $0.5^{\circ}$ bearing error in $2.0\~6.0$ GHz when SNR is 30 dB.

• Journal of Plant Biotechnology
• /
• v.32 no.4
• /
• pp.301-306
• /
• 2005

Conditions for efficient organogenesis and plant regeneration from Dianthus gratianopol suspension cultured cells were established. Shoot-forming calli of glossy surface, pale green and knobby type were selected from leaf explant-derived calli and were suspension-subcultured every week in CP liquid medium with 1.0 mg/L 2,4-D and 0.5 mg/L BAP. Combinations of 1.0 mg/L 2,4-D and 0.5 mg/L BAP, and 1.5 mg/L 2,4-D and 0.5 mg/L BAP were effective for the induction of regenerative callus from the suspension cultured cell clusters. Multiple shoot primordia were initiated from the green spots of these regenerative callus and formed shoots on MS medium with 1.0 mg/L TDZ and 0.5 mg/L PAA. Shoot regeneration frequency (calli regenerating at least one shoot) was about 87%. For plant regeneration, proliferated shoots were excised and transferred to MS medium with 0.1 mg/L NAA for root initiation after 9 weeks of culture. The regenerants were potted in soil and formed the flowering buds and petals. Also, adventitious shoots were formed from the excised green shoot primordia of regenerative callus and these shoots proliferated successfully and regenerated to whole plants.

• Journal of Korea Water Resources Association
• /
• v.38 no.7 s.156
• /
• pp.537-544
• /
• 2005

For the proper management of high pressurized gas storage caverns, analysis of groundwater flow field and inflow quantity according to the groundwater head, gas storage pressure and water curtain head should be performed. The finite element method has been widely used for the groundwater flow analysis surrounding underground storage cavern because it can reflect the exact shape of cavern. But the various simulations according to the change of design factors such as the width of water curtain, shape of cavern etc. are not easy when elements were set up. To overcome these limitations, two dimensional groundwater flow model is established based on the boundary element method which compute the unknown variable by using only the boundary shape and condition. For the exact computation of drainage rate into cavern, the model test is performed by using the exact solution and pre-developed finite element model. The test result shows that the model could be used as an alternative to finite element model when various flow simulations are needed to determine the optimizing cavern shape and arrangement of water curtain holes and so forth.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.41-48
• /
• 2000

In this study, microstructure and mechanical properties and electrical conductivities of in situ Cu-Fe-Xi(Xi=Ag, Cr or Co) alloy wires obtained by cold drawing combined with intermediate heat treatments have investigated. During cold working the primary and secondary dendrite arms are aligned along the drawing direction and elongated into filaments after deformation processing. The addition of Ag was found to be more effective in reducing the microstructural scale at the given draw ratio than that of Co or Cr throughout the drawing processing. The ultimate tensile strength and the conductivity of the Cu-Fe based composites containing Ag were higher than those of Cu-Fe composites containing Co or Cr. The good mechanical and electrical properties of Cu-Fe-Ag wires may be associated with the more uniform distribution of the finer filaments in the wires containing silver. The strength of Cu-Fe-Xi composites is dependent on the spacing of the Fe filaments in accord with a Hall-Petch relationship. The fracture surfaces of all the specimens showed ductile-type fracture and iron filaments occasionally observed on the fracture surfaces.

• Geophysics and Geophysical Exploration
• /
• v.18 no.3
• /
• pp.154-161
• /
• 2015

For efficiently designing neutron induced gamma spectroscopy sonde, Monte Carlo simulation is employed to understand a dominant location of thermal neutron and classify the formation elements from the energy peak of capture gamma spectrum. A pulsed neutron generator emitting 14 MeV neutron particles was used as a source, and flux of thermal neutron was calculated from the twelve detectors arranged at each 10 cm intervals from the source. Design for reducing borehole effects using shielding materials was also applied to numerical sonde model. Moreover, principal elements and quantities of numerical earth models were verified through the energy spectrum analysis of capture gamma detected from a gamma detector. These results can help to enhance the signal-to-noise ratio, and determine an optimal placement of capture gamma detectors of neutron induced gamma spectroscopy sonde.

• Journal of the Korean Geographical Society
• /
• v.50 no.1
• /
• pp.23-36
• /
• 2015

The temperature change patterns of climatic solar terms and their climatic fitness were analyzed. Harmonic analysis based on thirty-year(1981-2010) time-series data from sixty one weather stations across South Korea showed that the central peaks of the extreme heat had shifted toward start of autumn with increasing mean temperature. The overall climatic fitness of solar terms, such as major heat, frost descent, major snow, and major cold, was low, and it showed significant regional variations. The actual meteorological phenomenon representing each climatic solar term was observed much later than the day of the solar term at most weather stations. The number of observations, where an actual meteorological condition for each climatic solar term was recorded within ${\pm}1$ week from the day of that solar term, ranged only from 7.7% to 40.4% of the entire data. Study results also showed that the climatic fitness of major heat, frost descent, and major snow gradually changed in the east-west direction. Major cold, a solar term with higher climatic fitness, was influenced more strongly by latitude than longitude. Considering geographically uneven magnitude and trends in temperature changes, rearrangement and adjustment of time intervals between the solar terms may help us improve their applicability as realistic indicators of seasonal changes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.930-936
• /
• 2007

In this paper, the high gain and broadband antenna operating for SDMB(Satellite Digital Multimedia Broadcasting) system is realized, The proposed antenna consists of the SAP(Shorted Annular Patch) structure, which inhibits surface-wave and the parasitic SAP element with spacing of $0.25 {\lambda}_0$ in order to improve gain, bandwidth and directivity. The RHCP(Right Hand Circular Polarization) is generated by two slits, which are made along the periphery of the circular patch at the diametrically opposite points, The simulated maximum gain of the proposed antenna is 12.6 dBi, which is better 5.22 dBi than maximum gain of the conventional microstrip patch antenna. The measured maximum gain is 10.5dBi at operating frequency 2.63GHz. Also, the measured impedance bandwidth$(VSWR{\leq}2)$ of the proposed antenna is $360MHz(2.488{\sim}2.848 GHz)$, which is better 300 MHz than the bandwidth of the conventional microstrip patch antenna. The measured HPBW(Half Power Beam Width) of the proposed antenna is $45.8^{\circ}$, and the measured FBR(Front to Back Ratio) is 15.49 dBi, The 3dB axial ratio bandwidth is 220 MHz$(2.54{\sim}2.76 GHz)$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.771-780
• /
• 2014

We installed HF Radar of Array type in Site A and Site B, observing the real-time wave and current in the central East coast of Korea. WERA(WavE RAdar) in this research uses HF Radar of Array Type with frequency range of 24.525 MHz, developed by Helzel, Germany. Each site is a 8-Channel system consisting of four transmitters and eight receivers, generating wave and current data, being observed every thirty minutes at the present time. HF Radar has grid resolution of an interval of 1.5 km using bandwidth of 150 kHz; The wave data covers an observation range of about 25 km, and the current data covers the maximum observation range of about 50 km. The Wave data observed by HF Radar was compared and verified with the AWAC data observed in the research sites. MIT also compared the Current data observed by HF Radar with Monthly the East sea average surface current and current flow pattern provided by KOHA(Korea Hydrographic and oceanographic Administration). The regression line and deviation of the comparison data of Wave was calculated by Principal Component Analysis, which showed correlation coefficient 0.86 and RMSD 0.186. Besides, data analysis of long-term changes of the current in the East coast showed that, during August and September, the North Korean Cold Current flow into the southward direction and the East Korean Warm Current flow into the northward direction in the coast.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.5
• /
• pp.590-597
• /
• 1985

A recursive geometric adaptive control method to compensate for machining straightness error in the finished surface due to tool deflection and guideway error generated by end milling process is developed. The relationship between the tool deflection and the feedrate is modeled by a modified Taylor's tool life equation. Without a priori knowledge on the variations off cutting parameters, time varying parameters are then estimated by an exponentially windowed recursive least squares method with only post-process measurements of the straightness error. The location error is controlled by shifting the milling bed in the direction perpendicular to the finished surface and adding a certain amount of feedrate with respect to the tool deflection model before cutting. The waviness error is compensated by adjusting the feedrate during machining. Experimental results show that location error is controlled within a range of fixturing error of the bed on the guideway and that about 60% reduction in the waviness error can be achieved within a few steps of parameter adaption under wide operating ranges of cutting conditions even if the parameters do not converge to fixed values.