• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.523-523
• /
• 2013

대기압 제트 플라즈마는 의료산업 및 재료공정, 정수, 기체흐름 제어 등 다양한 분야에 적용을 위한 연구가 활발히 진행되고 있다. 뿐만 아니라 구동 조건에 따라 다양한 방전 모드가 존재하며, 이에 따라 발생된 플라즈마의 광학적 및 전기적 특성도 매우 다르게 나타나기 때문에 과학적으로도 새로운 현상들이 속속 발표되고 있다. 대기압 제트 플라즈마에서 중요한 과학적 현상 중 하나인 스트리머(streamer) 혹은 플라즈마 총알(plasma bullet)은 수-수십 kHz의 저주파 전압으로 구동 시 특정 조건에서 발생하는 현상으로, 최근 들어 시간분해능이 높은 ICCD 카메라를 이용하여 스트리머의 발생 및 전파에 대한 새로운 현상의 발견과 다양한 물리적 이해가 시도되고 있다. 본 연구에서는 헬륨 대기압 제트 플라즈마에 포함된 질소 함유량에 따른 다중 스트리머의 발생 및 기작의 이해를 시도하였다. 구동 전압 및 주파수, 헬륨기체의 유량, 전극 구조 및 간격 등 모든 조건이 동일한 상태에서 질소기체의 함유량을 증가시킬수록 특정 영역에서 스트리머의 개수가 증가하는 것을 관찰되었다. 또한 $N_2{^+}$의 방출광 세기가 헬륨 및 산소 원자의 방출광보다 지배적인 것으로 측정되었으며, 이는 헬륨 플라즈마에서 흔히 나타나는 헬륨 metastable에 의한 질소분자의 페닝 이온화(Penning ionization) 때문이다. 본 연구팀은 페닝 이온화($He^*+N_2{\rightarrow}He+N_2{^+}+e$)로 인해 추가적으로 발생하는 전자가 다중 스트리머 발생에 중요한 역할을 하는 것이라 제안한다. 좀 더 심화적인 분석을 하고자 헬륨-질소 플라즈마에서 주된 여러 가지 반응식을 이용하여 페닝 이온화에 의한 이온화율 및 전자의 직접적인 충돌에 의한 질소, 헬륨의 이온화율의 계산을 수행하여 특정 영역에서 헬륨의 이온화율보다 질소 페닝 이온화율이 더 커지는 것을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05a
• /
• pp.172-175
• /
• 2002

The technique of induced discharge by a pulsed CO2 laser is being applied to control electrical discharge path, material processing, triggered lightning for protecting the power equipments. In this paper, we have investigated about the characteristics of the induced discharge at atmospheric conditions by using a plasma channel, which is produced when a pulsed CO2 laser radiation is focused by a focusing mirror as a trigger source. A plasma channel produced by laser radiation has an effect on decreasing the threshold voltage and inducing the discharge in both needle electrodes. We have confirmed a delay time between a produced plasma channel and an electrical discharge after laser radiation. We provided the decreased voltage lower than the natural discharge voltage between electrode type of needles and was induced the discharge by forming a plasma channel between them. In this research we could understand the time delay of induced discharge by laser radiation, and the characteristics of the discharge cause by the decrease in the threshold voltage, and the polarity effect by changes of plasma channel positions between two electrodes.

• Journal of the Korean Magnetics Society
• /
• v.25 no.5
• /
• pp.149-155
• /
• 2015

The ECR (Electron Cyclotron Resonance) Ar ion milling was manufactured to fabricate the device of thin film. The ECR ion milling system applied to the device etching operated by a power of 600W, a frequency of 2.45 GHz, and a wavelength of 12.24 cm and transferred by a designed waveguide. In order to match one resonant frequency, a magnetic field of 908 G was applied to a cavity inside of ECR. The Ar gas intruded into a cavity and created the discharged ion beam. The surface of target material was etched by the ion beam having an acceleration voltage of 1000 V. The formed devices with a width of $1{\mu}m{\sim}9{\mu}m$ on the GMR-SV (Giant magnetoresistance-spin valve) multilayer after three major processes such as photo lithography, ion milling, and electrode fabrication were observed by the optical microscope.

• Korean Journal of Optics and Photonics
• /
• v.12 no.2
• /
• pp.103-108
• /
• 2001

In this paper, we designed and made the scanned point detecting system for 3-dimensional measurement of the light emitted from plasma display panel (PDP) , and we measured and analyzed 3-dimensional light emitted from a real PDP by using this scanned point detecting system. The scanned point detecting system has a point detector with a pinhole. The light emitted from the source at the in-focus position can pass through the pinhole and be collected by detector. The light from other sources at outof-focus positions is focused at points in front of or behind the pinhole, and thus it is intercepted by the pinhole. Therefore, we can detect light information from a particular point of a PDP cell of 3-dimensional structure. We know the electric field distribution inside the PDP cell from the 3-dimensionallight intensity distribution measured by using the scanned point detecting system. As the Z axial measurement increases, the intensity of light detected increases and intensity of light detected on the inside edge of the ITa electrode is larger than outside edge of the ITa eletrode and gap of the ITa electrodes. Also, as the measurement point moves from one barrier rib to another, the detected light is weaker near to the barrier ribs than at the center between the barrier ribs. The emitted light is concentrated at the center between barrier ribs. ribs.

• Applied Chemistry for Engineering
• /
• v.30 no.1
• /
• pp.23-28
• /
• 2019

We report a supercapacitor cable, which consists of three-dimensional (3D) porous graphene coated onto the surface of carbon thread. The 3D porous framework of graphene was constructed by microwave-activated process using a graphene oxide-coated carbon thread. The use of microwave irradiation enabled to convert graphene oxide into reduced graphene oxide without any reducing agents and activate graphene sheets into exfoliated and porous graphene sheets. Combining two wire electrodes with a polymer gel electrolyte successfully completed supercapacitor device in a form of cable construction. The supercapacitor cables were highly flexible, and thus can be transformed into various shapes of devices and be integrated into textile items. A high area-capacitance of 38.1 mF/cm was obtained at a scan rate of 10 mV/s. This capacitance was retained 88% of its original value at 500 mV/s. The cycle life was also demonstrated by repeating a charge/discharge process during 10,000 cycles even under bent states, showing a high capacitance retention of 96.5%.

• Fire Science and Engineering
• /
• v.33 no.1
• /
• pp.15-22
• /
• 2019

Refrigerator and heating cabinet fires due to the dielectric breakdown of electronic components caused by leaked beverages are being reported frequently. On the other hand, there has been little interest in measuring the electrical characteristics of beverages and studying the cause of fires. In this paper, the electrical conductivity and total dissolved solids (TDS) for 32 different beverages commonly sold in South Korea were measured to study the relationship between the electrical conductivity and dielectric breakdown. Out of these 32 beverages, based on the measurements, some characteristic beverages were selected and further dielectric breakdown tests were conducted. The results showed that the probability of a fire is higher for beverages with high electrical conductivity. Interestingly, beverages with low electrical conductivity had a high likelihood of fire depending on the type of beverage. Moreover, some conditions that cause spark ignition, which lead to fires in electronic components, were identified.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.941-947
• /
• 2018

In general, capacitors have a large influence on the life of the system due to frequent charging and discharging. In this paper, we analyze the cause of the core failure of high voltage, high current HVDC sub-module film capacitor and analyze the precautions of the capacitor design and manufacturing process. First, the cause of the fault, the failure mode, and the effect are analyzed through the FMEA of the capacitor. To quantitatively evaluate the causes and effects of faults that have the greatest effect on the failure of a capacitor, a fault tree for the capacitor is presented and the failure rate is analyzed according to the design parameters and the driving conditions. It is verified that the main cause of capacitor failure is the capacitance change, and it is necessary to minimize the temperature rise, corona occurrence, electrode expansion, and insulation distance decrease during capacitor design and manufacturing process in order to reduce the failure rate of the capacitor.

• Journal of Convergence for Information Technology
• /
• v.12 no.4
• /
• pp.338-344
• /
• 2022

It is necessarily required in developing Si-based anode materials for lithium ion batteries, and the related researches are actively working especially in Si-carbon composite material. On the other hand, the photovoltaic and semiconductor industries discard huge amount of Si resources, facing the environmental issue. In this study, recycled Si resource is adopted to obtain Si-carbon composite for LIB(Lithium-Ion Batteries). In order to improve high-capacity retention characteristics and cycle stability of a Si anode material for the LIB, two differenct composites having a mass ratio of silicon and pitch of 1:1 and 2:1 are synthesized and electrochemical characteristics of the anode material manufactured by simple self-assembly method. This result in excellent initial capacity with stable cycle life, and confirming the potential use of recycled Si material for LIB.

• Composites Research
• /
• v.36 no.6
• /
• pp.422-428
• /
• 2023

The electrical contact resistance between the bipolar plate (BP) and the carbon felt electrode (CFE), which are in contact by the stack clamping pressure, has a great impact on the stack efficiency because of the relatively low clamping pressure of the vanadium redox flow battery (VRFB) stack. In this study, a polyethylene (PE) composite-CFE hybrid bipolar plate structure is developed through a local heat welding process to reduce such contact resistance and improve cell performance. The PE matrix of the carbon fiber composite BP is locally melted to create a direct contact structure between the carbon fibers of CFE and the carbon fibers of BP, thereby reducing the electrical contact resistance. Area specific resistance (ASR) and gas permeability are measured to evaluate the performance of the PE composite-CFE hybrid bipolar plate. In addition, an acid aging test is performed to measure stack reliability. Finally, a VFRB unit cell charge/discharge test is performed to compare and analyze the performance of the developed PE composite-CFE hybrid BP and the conventional BP.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.3
• /
• pp.172-180
• /
• 2012

The $LiMn_2O_4$ cathodes for lithium ion battery were synthesized from various precursors of manganese oxides and manganese hydroxides. As the first step, nanosized precursors such as ${\alpha}-MnO_2$ (nano-sticks), ${\beta}-MnO_2$ (nano-rods), $Mn_3O_4$ (nano-octahedra), amorphous $MnO_2$(nano-spheres), and $Mn(OH)_2$ (nano-plates) were prepared by a hydrothermal or a precipitation method. Spinel $LiMn_2O_4$ with various sizes and shapes were finally synthesized by a solid-state reaction method from the manganese precursors and LiOH. Nano-sized (500 nm) octahedron $LiMn_2O_4$ showed high capacities of 107 mAh $g^{-1}$ and 99 mAh $g^{-1}$ at 1 C- and 50 C-rate, respectively. Three dimensional octahedral crystallites exhibit superior electrochemical characteristics to the other one-dimensional and two-dimensional shaped $LiMn_2O_4$ nanoparticles. After 500 consecutive charge discharge battery cycles at 10 C-rate with the nano-octahedron $LiMn_2O_4$ cathode, the capacity retention of 95% was observed, which is far better than any other morphologies studied in this work.