• Journal of Aerospace System Engineering
• /
• v.17 no.2
• /
• pp.94-102
• /
• 2023

A nylon wire holding and release mechanism (HRM) has been widely used for deployable applications of CubeSat owing to its simplicity and low cost. In general, structural safety of solar panel with an HRM has been designed by performing structural analysis under a launch environment. However, previous studies have not performed thermal analysis for HRM in an on-orbit environment. In this study, Launch and Early Orbit Phase (LEOP) thermal analysis was performed to evaluate thermal stability of the mechanism in the orbital thermal environment of the pogo pin-based HRM applied to CubeSat. In addition, the effectiveness of the thermal design and performance of the pogo pin-based HRM were verified through a thermal vacuum test.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2001.06a
• /
• pp.115-115
• /
• 2001

경주시 양남면의 4기 단층으로 추정되는 수렴단층에 의해 절단되는 해안단구 퇴적층 풍화단면에서 저결정질 광물인 앨로패인 교결층을 기재하였다. 이들은 자갈퇴적층 내에 협재하는 수조의 모래층에 한정되어 형성되어 있으며, 3-17 cm 두께로 연장성이 매우 좋다. 편광현미경 관찰에 의하면 모래층에는 사장석편들이 다량 함유되어 있으며 앨로패인은 광학적 등방성의 치밀한 점토집합체들로서 사장석 입자를 선택적으로 교대하거나 자갈과 모래입자들을 피복하고 있다. 앨로패인은 광학적 이방성인 상하위층의 고령토질 점토피복물과 명확히 구분된다. 앨로패인의 전자현미분석에 의하면, Al/Si 원자비가 1.3-1.7 범위이고 평균값은 1.5이다. X선회절분석 결과 3.49$\AA$과 2.26$\AA$에서 두 개의 넓은 회절대가 관찰된다. 주사 및 투과전자현미경관찰에 의하면 앨로패인을 특정한 입자형태 없이 치밀한 겔상태를 이루고 있다. 열분석에 의하면 96$^{\circ}C$에서 큰 흡열피크와 992$^{\circ}C$에서 발열피크가 관찰되며, 총 45% 정도의 중량감소를 보인다. 사장석의 평균조성은 An$_{87}$이며, 사장석내 유리포유물의 전자현미분석결과는 화산암 화학분류도에서 현무암 영역에 도시된다. 이 지역의 기반암은 현무암질 라필리응회암이나 사장석편을 제외하고 벤토나이트화되어 있다. 따라서 해빈환경에서 사장석이 벤토나이트에서 분리되어 퇴적한 것으로 보인다. 앨로패인 교결층은 해수면 강하로 단구퇴적층이 지표로 노출된 후, Al의 함량이 높고 비교적 풍화에 약한 사장석이 선택적으로 풍화되어 생성되었다. 앨로패인으로 피복된 모래층 내의 자갈은 풍화반응이 지체되어 상하위층의 자갈과 비교하여 풍화도에 있어서 현저한 차이를 보인다.. 파이프 중심에서 외곽부로 갈수록 전기석의 함량은 줄어들고 있고 장석들이 알바이트ㆍ칼스베드 쌍정을 보이며, 흑운모가 각섬석보다는 우세하게 나타나고 있다. 전기석은 주상 결정, 자형 내지 반자형의 입자로 다색성을 보이며, 결정 중심에서 가장자리로 갈수록 파란색과 황갈색의 광학적 누대구조를 관찰할 수 있다. 일광광산에서 산출되는 전기석에 대한 현미경 관찰은 열수기원임을 지시하고 있다. 야외조사와 현미경 관찰의 예비조사에 의하면 일광광산의 전기석이 형성된 환경은 다른2가지 화학적인 저장소의 혼합 효과의 결과로 생성되어진 것으로 예상된다. 일광의 화강암류를 만든 마그마는 전기석을 형성할 만큼의 Fe-Mg성분이 충분하지 않았을 것이다. 화강암 내에 흑운모와 각섬석의 결정작용에 의해 마그마의 Fe-Mg성분이 고갈되어지고 이로 인해 그 함량이 감소하며 상대적으로 마그마 내에 남은 붕소(B$_2$O$_3$)는 열수로 용리되고 흑운모, 각섬석과 평형을 유지하며 열수에 남아있게 된다. 잔류용융체에 남은 붕소의 함량은 전기석을 만들기에 충분함에도 불구하고, Fe-Mg 함량이 부족하여 마그마 기원의 전기석 결정을 만들 수가 없다가 광맥이 형성된 시기에 또 다른 열수가 공급되면서 이전의 평형이 깨지고 기존의 흑운모와 같은 염기성 광물이 붕소(B)를 함유한 새로운 열수와 반응하여 전기석을 형성한 것으로 예상한다. 앞으로 전암과 광물에 대해 지화학적 연구를 통해 화강암류와 전기석과의 지화학적 연관성, 주성분 원소와 열수의 특성과의 상관관계, 전기석의 기원(마그마 기원인지 열수기원인지)이 보다 정확하게 파악될 것이다. 마그마 진화에 따른 전기석의 성분변화와 기원을 이용하여 일광광산의 동광화대를 형성한 마그마 계에서 열수계로 이어지는 지질학적 과정을 이해할 수 있을 것이며, 암석 성인론적 지시자로서

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.230-237
• /
• 2011

The study was performed to investigate the characteristics of charcoal and temperature change of a kiln's inner and outer walls in carbonization process using improved kiln. In this kiln system, carbonization process was completed in eight days. In the kiln, the ignition temperature was kept about $720^{\circ}C$. And then the temperature were increased gradually prior to be refined. Finally, the temperature in refining process was reached to maximum point, $1,000^{\circ}C$. In the chimney, the temperature was increased gradually from $90^{\circ}C$ at ignition to $750^{\circ}C$ at refining. The temperature change of the kiln wall resembles a temperature change progress curve during a carbonization process. The highest temperature of the kiln wall that appeared by a carbonization process was around $500^{\circ}C$. As a result of having measured an inner wall and the outer wall of the kiln using an infrared thermography camera, it was judged with there being considerable latent heat on kiln wall and ceiling. Fixed carbon contented of charcoal was 85.9~89.9%. Refining degree of charcoal, hardness, calorific value and pH were l, 12, 7,047~7,456 kcal/kg, 9.0~9.9, respectively. The yield of wood charcoal was 13.8%, and compared to conventional kiln's yield increased 1.5%.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.210-218
• /
• 2015

The reaction behavior of rigid polyurethane foams were studied on the effects of gelling catalysts of amine type, such as; dimethylcyclohexyl amine (DMCHA) and of potassium type, such as; potassium octoate (PO). Rigid polyurethane foams were provided with polymeric 4,4'-diphenylmethane diisocyanate, polyester polyol, silicone surfactant, blowing agent and a few gelling catalysts. As the contents of catalyst, DMCHA increased from 0 to 2.0 g, the reaction time decreased from ca. 330 to ca. 35 sec and due to the exothermic reaction, the maximum temperature increased from ca. 217 to ca. $234^{\circ}C$, respectively. As the contents of PO increased from 0 to 2.5 g, the reaction time decreased from ca. 79 to ca. 38 sec and the maximum temperature increased from ca. 182 to ca. $271^{\circ}C$, respectively. The kinetic parameters were calculated and the conversions were based on the temperature rising method of adiabatic process. As the content of DMCHA increased, the rate constant $k_0$ increased. But in the case of PO catalyst, $k_0$ did hardly depend upon its amount, and showed us similar reaction rate constants.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.279-285
• /
• 2017

In this study, the development of concrete preventing initial frost damage and durability about that were evaluated by using anti-aging agent and admixture(reduced slag). As a result of experiment, initial hydration heat was increased by $C_{12}A_7$ of reduced slag components but it was not effective to development of strength. Also fluidity decreased with increasing replacement of reduced slag. This suggested that fluidity was low by rapid setting due to absent of gypsum in reduced slag components. In case of CR2G specimen that added 4% gypsum, the flow ability was higher than plain. It is considered that concrete developed using reduced slag should use $SO_3$. Result of durability experiments, the durability decreased with increasing replacement amount of reduced slag.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.2
• /
• pp.131-138
• /
• 2019

Recently, there are many structures exposed to severe outdoor environments, which results in rapid degradation of durability of the concrete structures. there can be rapid deterioration of the concrete structures from early frost damage due to the insufficient curing in low outdoor temperature condition. The objective of this study is to investigate the effect of thickness change conditions and binding material on early frost damage depth of the concrete exposed to cold weather in winter, and is to clearly assess damage depth of the concrete structure due to early frost damage. Specimens with 300x300x(150, 200, 250, 300mm) were prepared. OPC and OPC+FA+BS were adopted for binders. Test results indicate that the depth of the early frost damage was deeper with the decrease of thickness of members. The brightness of specimens were reduced when the member thickness was thinner. When determining the depth of early frost damage, it can be distinguished into dark color and relatively bright color when dried for approximately 30 minutes in the indoors of $20^{\circ}C$ in temperature and 60% in relative humidity after submerging in water for 24 hours. The dark colored part can be determined easily when measured with vernier calipers.

• The Korean Journal of Nuclear Medicine
• /
• v.33 no.3
• /
• pp.298-305
• /
• 1999

Purpose: N-(3-[$^{18}F$]Fluoropropyl)-$2{\beta}$-carbomethoxy-$3{\beta}$-(4-iodophenyl)nortropane [$^{18}F$]FP-CIT) has been shown to be very useful for imaging the dopamine transporter. However, synthesis of this radiotracer is somewhat troublesome. In this study, we used a new method for the preparation of [$^{18}F$]FP-CIT to increase radiochemical yield and effective specific activity. Materials and Methods: [$^{18}F$]FP-CIT was prepared by N-alkylation of nor-${\beta}$-CIT (2 mg) with 3-bromo-1-[$^{18}F$]fluoropropane in the presence of $Et_3N$ (5-6 drops of $DMF/CH_3CN$, $140^{\circ}C$, 20 min). 3-Bromo-1-[$^{18}F$]fluoropropane was synthesized from $5{\mu}L$ of 3-bromo-1-trifluoromethanesulfonyloxypropane (3-bromopropyl-1-triflate) and $nBu_4N^{18}F$ at $80^{\circ}C$. The final compound was purified by reverse phase HPLC and formulated in 13% ethanol in saline. Results: 3-Bromo-1-[$^{18}F$]fluoropropane was obtained from 3-bromopropyl-1-triflate and $nBu_4N^{18}F$ in 77-80% yield. N-Alkylation of nor-${\beta}$-CIT with 3-bromo-1-[$^{18}F$]fluoropropane was carried out at $140^{\circ}C$ using acetonitrile containing a small volume of DMF as the solvents. The overall yield of [$^{18}F$]FP-CIT was 5-10% (decay-corrected) with a radiochemical purity higher than 99% and effective specific activity higher than the one reported in the literature based on their HPLC data. The final [$^{18}F$]FP-CIT solution had the optimal pH (7.0) and it was pyrogen-free. Conclusion: In this study, 3-bromopropyl-1-triflate was used as the precursor for the [$^{18}F$]fluorination reaction and new conditions were developed for purification of [$^{18}F$]FP-CIT by HPLC. We established this new method for the preparation of [$^{18}F$]FP-CIT, which gave high effective specific activity and relatively good yield.

• Clinical and Experimental Pediatrics
• /
• v.52 no.2
• /
• pp.199-204
• /
• 2009

Purpose : Seizure associated with fever may indicate the presence of underlying inherited metabolic diseases. The present study was performed to investigate the presence of underlying metabolic diseases in patients with complex febrile seizures, using analyses of urine organic acids. Method : We retrospectively analyzed and compared the results of urine organic acid analysis with routine laboratory findings in 278 patients referred for complex febrile seizure. Results : Of 278 patients, 132 had no abnormal laboratory findings, and 146 patients had at least one of the following abnormal laboratory findings: acidosis (n=58), hyperammonemia (n=55), hypoglycemia (n=21), ketosis (n=12). Twenty-six (19.7 %) of the 132 patients with no abnormal findings and 104 (71.2%) of the 146 patients with statistically significant abnormalities showed abnormalities on the organic acid analysis (P<0.05). Mitochondrial respiratory chain disorders (n=23) were the most common diseases found in the normal routine laboratory group, followed by PDH deficiency (n=2) and ketolytic defect (n=1). In the abnormal routine laboratory group, mitochondrial respiratory chain disorder (n=29) was the most common disease, followed by ketolytic defects (n=27), PDH deficiency (n=9), glutaric aciduria type II (n=9), 3-methylglutaconic aciduria type III (n=6), biotinidase deficiency (n=5), propionic acidemia (n=4), methylmalonic acidemia (n=2), 3-hydroxyisobutyric aciduria (n=2), orotic aciduria (n=2), fatty acid oxidation disorders (n=2), 2-methylbranched chain acyl CoA dehydrogenase deficiency (n=2), 3-methylglutaconic aciduria type I (n=1), maple syrup urine disease (n=1), isovaleric acidemia (n=1), HMG-CoA lyase deficiency (n=1), L-2-hydroxyglutaric aciduria (n=1), and pyruvate carboxylase deficiency (n=1). Conclusion : These findings suggest that urine organic acid analysis should be performed in all patients with complex febrile seizure and other risk factors for early detection of inherited metabolic diseases.

• Journal of the Society of Disaster Information
• /
• v.10 no.4
• /
• pp.583-597
• /
• 2014

Fire caused by heater has various causes as many as the types of heater. also, lots of damage of human life and property loss are caused, since annually continuous fire accident by heater in traditional market is frequently occurring. There are not many cases of fire due to heater in most of residential facilities such as general house, apartments, etc., because they are supplied with heating boiler, however the restaurant, store and office of the market, sports center, factory, workplace, etc. still use heater, e.g. oilstove, electric heater, etc., so that they are exposed to fire hazard. Also, when investigating the number of fire due to heater, it was analyzed to occur in order of home boiler, charcoal stove, oilstove, gas heater/stove, electric stove/heater, the number of fire per human life damage was analyzed in order of gas heater/stove, oil heater/stove, electric heater/stove, briquette/coal heater. Also, gas and oil related heater were analyzed to have low frequency, however, with high fire intensity. Therefore, this research aimed at considering more scientific fire inspection and identification approach by reenacting and reviewing fire outbreak possibility caused by combustibles' contact and conductivity under the normal condition and abnormal condition in respect of ignition hazard, i.e. minimum ignition temperature, carbonization degree and heat flux along with it, due to oilstove and electric stove, which are still frequently used in public use facility, traditional market, and, of which actual fire occurrence is the most frequent. As the result of reenact test, ignition hazard appeared very small, as long as enough heat storage condition is not made in both test objects(oilstove/electric stove), however carbonization condition was analyzed to be proceeded per each part respectively. Eventually, transition to fire is the ignition due to heat storage, so that it was analyzed to ignite when minimum heat storage temperature condition of fire place is over $500^{\circ}C$. Particularly, in case of quartz pipe, the heating element of electric stove, it is rapidly heated over the temperature of $600^{\circ}C$ within the shortest time(10sec), so that the heat flux of this appears 6.26kW/m2, which was analyzed to result in damage of thermal PVC cable and second-degree burn in human body. Also, the researcher recognized that the temperature change along with Geometric View Factor and Fire Load, which display decrease of heat, are also important variables to be considered, along with distance change besides temperature condition. Therefore, the researcher considers that a manual of careful fire inspection and identification on this is necessary, also, expects that scientific and rational efforts of this research can contribute to establish manual composition and theoretical basis on henceforth fire inspection and identification.

• Pediatric Infection and Vaccine
• /
• v.5 no.1
• /
• pp.79-87
• /
• 1998

Purpose : The P1 protein of Mycoplasma pneumoniae mediates the attachment of the pathogen to its host cell and elicits a strong humoral immune response during infection with this organism. Mycoplasma pneumoniae strains can be classified into two groups(I and II) by PCR method of P1 cytadhesin gene. In this study, we evaluated the prevalence, epidemiological and clinical characteristics of each group. Methods : From 155 patients with Mycoplasma pneumoniae, who admitted to the Department of Pediatrics, Sung-Ae and Kwangmyung Sung-Ae Hospital between November 1996 and October 1997, we collected their throat swabs or nasopharyngeal aspirates for DNA extraction and serum for indirect hemagglutination test of Mycoplasma pneumoniae. The group specific PCR amplification were performed using specific oligonucleotide primers designed for P1 gene genotyping. Results : Group I(137 patients, 88.4%) occurred frequently than group II(18 patients, 11.6%). In both group, the most prevalent season was winter in 1996(Nov. to Dec.) and fall in 1997(Aug. to Oct.) The prevalent age was four to six years old. The number of male was more than female in both group; Group 1(1.2:1), Goup 2(1.6:1). No significant relationship were found between two groups in duration of fever and hospital days(P>0.05). The rate of high antibody titers(>1:5120) was lower in group I(6/137, 4.4%) than group II(2/18, 11.1%). Conclusion : Group I was much more prevalent than group II during 1996~1997 in Korea. There was no difference between two groups in epidemiological and clinical parameters except the rate of high antibody titers. Further follow-up survey will be needed for the epidemiologic and clinical studies of Mycoplasma pneumoniae in Korea.