저궤도 위성이 발사체에서 분리된 후 탑재 소프트웨어에 의한 초기 동작이 수행되고 나면 초기 운용이 시작된다. 초기 운용 기간에 수행할 모든 절차와 대처 가능한 긴급 상황이 발생할 경우 수행할 절차는 발사 전에 미리 준비된다. 위성의 각 부분의 설계 마진은 최악 조건을 기준으로 반영되어 있기 때문에 발사 이후의 버스 시스템 관점에서의 위성 특성은 요구 사항을 만족하는 범위가 될 것으로 예상이 가능하다. 실제로 발사 후 위성 텔레메트리 분석을 통해 대부분의 항목에서 요구 조건을 만족하는 것으로 확인되었다. 또한 텔레메트리 분석을 통해 설계 단계에서 예상했던 것 보다 정확한 궤도 특성이 반영된 위성 특성을 파악하였다. 이러한 특성은 설계 시 고려했던 상황과 다르더라도 실제 궤도 특성이 반영된 특성이므로 초기 운용 및 정상 운용 시에 정상적인 상황인 것으로 고려해야 한다. 첫째, 지구 알베도 특성에 따라 태양센서 값이 궤도에 따라 변화한다. 위성의 자세가 정확히 태양을 지향하고 있더라도 태양센서에 지구에서 반사된 빛이 입사되어 자세 제어에 영향을 주게 된다. 알베도의 영향은 적도에서 극지방으로 갈수록 커지며, 계절에 따라 다른 특성을 보인다. 알베도의 영향을 최소화하기 위해 자세 제어 모델에 알베도 효과를 고려하거나 알베도 효과를 무시할 수 있을 정도로 자세 제어 오차 한계를 조정할 수 있다. 둘째, 위성의 지구 회피 회전에 의해 태양 전지판의 온도가 궤도에 따라 변화한다. 위성체는 위성체에 장착된 두 개의 별센서의 가시성 확보를 위해 태양 지향 자세에서 요축으로 일정 속도로 회전한다. 남극 부근에서는 두 태양 센서가 모두 지구의 반대편인 남쪽을 지향하도록 하며, 북극 부근에서는 북쪽을 지향하도록 한다. 이 때 두 태양 센서의 방향에 장착된 태양 전지판은 극지방에서 지구 반대편에 위치하므로 다른 태양 전지판에 비해 낮은 온도를 갖게 된다. 이 논문에서는 위성의 궤도 특성에 따른 고려 사항에 대해 설명하였다.
Journal of the Korean Society of Propulsion Engineers
/
v.5
no.1
/
pp.18-25
/
2001
The results of systematic numerical experiments of secondary gas injection thrust vector control are presented. The effects of secondary injection system such as injection location and nozzle divergent cone angle onto the overall performance parameters such as thrust ratio, specific impulse ratio and axial thrust augmentation, are investigated. Complex nozzle exhaust flows induced by the secondary jet penetration is numerically analyzed by solving unsteady three-dimensional Reynolds-averaged Navier-Stokes equations with Baldwin-Lomax turbulence model for closure. Numerical simulations compared with the experiments of secondary air injection into the rocket nozzle of $9.6^{\cire}$ divergent half angle showed good agreement. The results obtained in terms of overall performance parameters showed that locating the secondary injection orifice further downstream of primary nozzle ensures the prevention of occurrence of reflected shock wave, therefore is suitable for efficient and stable thrust vectoring over a wide range of use.
The Journal of Korean Institute of Electromagnetic Engineering and Science
/
v.28
no.2
/
pp.129-138
/
2017
This paper has been shown for the extraction of Doppler signature from the radar signal for an air-breathing targets tracked in the ground radar. For the extractions, a Doppler resolution is confirmed from mathematical modeling of PT(pulse train) waveform. Doppler signatures of air-breathing target are varied to radar aspect angle of engine and are determined from physical parameter of jet engine. To confirm such Doppler signatures, the radar signal reflected from the air-breathing target is obtained by our radar signal storage. After this extraction, radar aspect angle of engine has estimated from tracking information. Relative differences of Doppler signatures to radar aspect angle of engine is verified from these results and Doppler profiles for radar target identification appliance are presented.
The Journal of the Korea institute of electronic communication sciences
/
v.6
no.3
/
pp.343-348
/
2011
With the rapid and wide-spread use of mobile communications much attention has been focussed on propagation in the urban area crowed with buildings. It is often surrounded by hills, forests, and mountains. The importance of surface scattering interference between transmitters and receivers on the rough surfaces has been interested and investigated. Therefore, a prediction method is necessary to estimate the influence of rough surfaces on microwave radio propagation. Moreover, most of the mobile communications are performed based on the digital communication system rather than the analog one. In this case, we must pay more careful attention to the signal delay caused by the phase delay due to the multi-path propagation. In this paper we have analyzed numerically scattering of electromagnetic waves from Composite structures by using FVTD (Finite Volume Time Domain) method. We consider two different types of rough surfaces such as periodic and composite structures.
Although radiosity can represent diffuse reflections of the object surfaces by modeling energy exchange in 3D space, there are some restrictions for real-time applications because of its computation loads. Therefore, GPU(Graphics Processing Unit) based radiosity algorithms have been presented actively to improve its rendering performance. We implement the progressive refinement radiosity on GPU by G. Coombe in 3D scene that is constructed with HDR(High Dynamic Range) radiance map. This radiosity method can generate a photo-realistic rendering image in 3D space, where the synthetic objects were illuminated by the environmental light sources. In the simulation results, the rendering performance is analyzed according to the resolution of the texel in the environmental map and mipmaping. In addition, we compare the rendering results by our method with those by the incremental radiosity.
Journal of the Korea Institute of Information and Communication Engineering
/
v.14
no.8
/
pp.1752-1758
/
2010
A FM-CW radar is used for the various purposes as a remote sensing device since it has the advantages of the relatively simple implementation and the low probability of signal interception. A FM-CW radar uses the same frequency modulated continuous wave for both transmission and demodulation. Therefore, the received beat frequency represents the range and Doppler information of targets. However, using the conventional FFT method, the degree of accuracy and resolution in the spectrum estimation can be seriously degraded in the detection and tracking of fast moving targets because of the short dwell time. Therefore, in this paper, the model parameter estimation methods called as an autoregressive method is applied to overcome these problems and showed that the improved accuracy and resolution can be obtained for the target range and velocity estimation.
Park, Jin-Ki;Park, Jong-Hwa;Na, Sang-Il;Beak, Shin-Chul
Proceedings of the Korea Water Resources Association Conference
/
2012.05a
/
pp.760-760
/
2012
도심 지역은 인구집중, 토지 피복의 변화 및 교통량 증가 등의 인공열 배출원의 다양화 등의 요인에 의해 주변지역보다도 기온이 높은 도시 열섬(Urban Heat Island) 현상에 의해 독특한 도시기후의 특색을 보이게 된다. 일반적으로 도시 열 환경에 대한 연구는 도시 열섬의 강도나 현상을 파악하는데 집중되어 왔다. 최근 들어 도시 열섬 현상 완화 또는 개선을 위한 관심이 높아지면서 도시내에 존재하는 수면이나 녹지를 이용한 기후개선에 대한 연구가 진행되고 있다. 하천은 다양한 생물이 서식하는 공간이면서 생물의 다양성이 풍부한 생태계의 보고로 인간과 환경이 조화를 이루어 온 공간이기도 하다. 이와 같이 하천은 지역의 다양성과 특수성에 따라 가지고 있는 기능이 다양하다. 그 중 하천의 환경 기능은 많은 열용량을 축적시켜 수면의 온도상승을 적게 하여 하천의 온도는 물론 주변지역의 온도를 낮추는 역할을 하게 된다. 특히 흐르는 물은 대류와 혼합과정을 거치며 열을 운반할 수 있으므로 효율적인 축열체가 된다. 또한 하천의 물 등은 광의 투과성이 높기 때문에 표면에서는 반사되지 않고 수체 내에 열을 저장한다. 따라서 이러한 현상이 종합적으로 작용하여 도심하천은 도심지에서 높게 형성된 온도를 낮추는 냉각효과가 있다고 판단된다. 이러한 영향을 알아보기 위해 본 연구에서는 원격탐사 기법을 이용하여 도심하천이 도시 열완경 완화에 미치는 영향을 분석하였다. 분석을 위해 2009년 9월 6일 Landsat 7 ETM+ 위성영상을 이용하여 LST (Land Surface Temperature)를 추출하고, SEBAL (Surface Energy Balance Algori- thms for Land) 모델을 이용하여 지표면 열수지 성분을 추출하였다. 그 결과, 도심하천 주변의 온도가 도심지에 비해 $2{\sim}3^{\circ}C$ 정도 낮게 형성되었으며, 잠열은 주변 도심지에 비해 하천에서 높은 분포를 나타내었다. 그러나 하천 둔치나 하천 주변의 콘크리트, 아스팔트 및 나대지 등의 토지피복은 지표면 온도가 높게 형성되어 도심의 heat spot으로 작용하여 열 환경을 악화시키나 도심하천은 cool spot 작용을 하여 도심의 열을 완화하는 기능을 갖는 것으로 판단된다.
Journal of the Korean Society of Fisheries and Ocean Technology
/
v.46
no.2
/
pp.157-163
/
2010
The indirect target strength (TS) estimation method which uses the Kirchhoff ray mode model (KRM model) was discussed to apply for a biomass estimation in the water of mixed species. TS of 25 live scorpion fishes for 120kHz were measured by a tethered method and of others dominant 5 species in the marine ranching ground of Jeju coastal water including a scorpion fish were also estimated by KRM model. The measurement TS of scorpion fish well agreed with the theoretical values and the standard formula of scorpion fish was estimated as $TS_{120kHz}=20Log\;(L)-72.9$ ($r^2=0.67$). TScm values estimated on trial to each sample of dominant 5 species were from -69.3dB to -75.1dB at 120kHz and they were in the general range of swimbladdered fish. It was clarified that TS by KRM model can be used to estimate fish biomass estimation by increasing a sample number and is more effective under the condition that there is rare TS information for inhabiting species in mixed-species area.
An area corresponding to the spatial resolution of optical remote sensor imagery often includes more than one pure surface material. In such case, a pixel value represents a mixture of spectral reflectance of several materials within it. This study attempts to apply the spectral mixture analysis on forest and to evaluate the information content of endmember fractions resulted from the spectral unmixing. Landsat-7 ETM+ image obtained over the study area in the Kwangneung Experimental Forest was initially geo-referenced and radiometrically corrected to reduce the atmospheric and topographic attenuations. Linear mixture model was applied to separate each pixel by the fraction of six endmember: deciduous, coniferous, soil, built-up, shadow, and rice/grass. The fractional values of six endmember could be used to separate forest cover in more detailed spatial scale. In addition, the soil fraction can be further used to extract the information related to the canopy closure. We also found that the shadow effect is more distinctive at coniferous stands.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2012.05a
/
pp.278-281
/
2012
Numerical studies were performed to investigate the three-dimensional front structure and dynamics features of detonation wave propagating in a circular tube such as Pulse Detonation Engine (PDE). By carrying out a series of parametric study using one step irreversible Arrhenius kinetics model, mechanisms of the three-dimensional front structure were investigated for two-, three-, four and six-cell mode detonations. A comparison with two-dimensional results, the effects of slapping transverse waves in radial direction were confirmed. In the all muti-cell modes, the detonation front structures and smoked-records on the wall are formed by the propagation of transverse waves along the wall in clockwise and counter-clockwise while the slapping move in radial direction. And the strength of reflected waves on the curved wall is changed by the multi-dimensional confinement effect.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.