• Journal of Welding and Joining
• /
• v.12 no.1
• /
• pp.73-79
• /
• 1994

Low cycle fatigue test was performed by companion specimens method to compare the properties of cyclic strain for the weldments of controlled rolling steel CR60 and welding structural steel SM58Q. And the result does not showed any difference of low cycle fatigue life between weldments. Especially, the values of coefficient of cyclic plastic strain $C_{p}$ and exponent of cyclic plastic strain $K_{p}$ of heat affected zones of CR60 steel and SM58Q steel were same. And $C_{p}$ and $K_{p}$ of CR60 steel were equal to the values of weld it means a good combination between the base metal, the heat affected zone and the weld of CR60 steel.eel.eel.

• Geotechnical Engineering
• /
• v.11 no.1
• /
• pp.113-126
• /
• 1995

Both resonant column (RC) and torsional shear(TS) tests were performed at small to intermediate strain levels to investigate deformational characteristics of cohesive soils. The effects of variables such as strain amplitude, loading frequency, and number of loading cycles were studied. Plasticity index was found to be an important variables in evaluating these effects. Soils tested include undisturbed silts and clays and compacted subgrade soils. At small strains below the elastic threshold, shear modulus is independent of number of loading cycles and strain amplitude. Small strain material damping exists wi th ranges be tween 1.1% and 1.7% for 75 tests. The elastic threshold strain increases as confining pressure and plasticity index increases. Above the cyclic threshold strain, the modulus of cohesive soil decreases with increasing number of cycles while damping ratio is almost independent of number of load cycles. Moduli and damping ratios of cohesive soils obtanined by RC test are higher than those from 75 test because of the frequency effect. Shear modulus of cohesive soil increases linearly as a function of the logarithm of loading frequency.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.40-40
• /
• 2003

최근 나노기술의 발달과 더불어 나노재료에 대한 특성평가 요구가 높아지고 있고, 따라서 나노스케일에서 재료의 기계적 거동을 분석할 수 있는 나노인덴테이션 기법이 심도있게 연구되고 있다. 본 연구에서는 나노인덴테이션, 주사탐침현미경(SPM), 투과전자현미경(TEM) 기법을 이용하여 여러가지 재료의 탄성 소성 변형 거동과 팝인/괍아웃 현상을 조사하고 해석하였다. 나노인덴테이션 기법으로는 50 마이크로뉴턴 (5 mg) 이하의 매우 작은 하중 하에서는 접촉 응력조건이라도 인장시험에서 관찰되는 영구변형이 제로인 완전탄성 변형 거동을 관찰할 수 있었다. 또한, 50-250 마이크로 뉴턴의 하중 범위에서 재료는 탄성변형 이후에 갑작스런 항복거동과 더불어 수십-수백 나노미터를 미끌어지듯 변형하는 팝인(pop-in), 또는 탈선(excursion) 현상을 관찰할 수 있었다. 이 현상은 하중을 가하는 동안에 여러 번 발생하였으며 재료의 표면상태와 전위밀도와 밀접한 상관관계를 보였다. 반복 압입 시험에서는 전형적인 가공경화 현상으로 항복점이 높아지고 새로운 항복점 이후에야 다시 팝인 발생함을 보였다. 한편, 하중을 가할 때 발생하는 팝인과는 달리 하중을 제거할 때 급격히 회복하는 팝아웃 현상 또한 관찰되었다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.2
• /
• pp.195-204
• /
• 2004

A series of constant creep and repeated creep tests are performed to investigate the behavior of visco-elasto-plastic materials of chemical grouted sands. In the result of constant creep test, the material exhibits three types of shear strain : elastic, plastic, viscoelastic. The elastic, plastic and viscoelastic strains are linear, i.e., the strains are proportional to the stresses for loading. Good agreement is found between the predicted viscoelastic and test results by the power law and the generalized model. In the repeated creep test, the instantaneous recoverable strain is time-independent and the magnitude of accumulated plastic strain increases with number of cycles. Also it is seen that the accumulated plastic strains are approximately proportional to stress. There are no significant differences between test results predicted values for first cycle, and the differences increase relatively insignificantly with number of cycles.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.115-121
• /
• 2010

To evaluate the engineering characteristics of aggregate base materials, cyclic triaxial, CBR and permeability tests were performed for 15 samples. The CBR values of aggregate base materials have wide range from 32 to 110(average 81) and the amount of swelling in submerged conditions has below 0.04mm. The Modulus of aggregate base materials were significantly affected by volumetric stress, linear volumetric model was best for fitting. The modulus of aggregate base materials were determined within range of 100MPa~600MPa, 80~270 and 0.1~0.6 for model coefficient $k_1$ and $k_2$ respectively. The empirical correlation model was suggested that prediction the modulus from the basic properties obtained from particle size distribution test and compaction test. The coefficient of determination of the proposed correlation model was 0.423 for model coefficient $k_1$, 0.920 for model coefficient $k_2$ and 0.872 for modulus with stress level.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.261-271
• /
• 2003

A condition evaluation procedure for the pavement foundations using multi-load level Falling Weight Deflectometer(FWD) deflections is presented in this paper. A dynamic finite element program incorporating a stress-dependent material model, was used to generate the synthetic deflection database. Based on this synthetic database, the relationships between surface deflections and critical responses, such as stresses and strains in base and subgrade layers, have been established. FWD deflection data, Dynamic Cone Penetrometer(UP) data, and repeated load resilient modulus testing results used in developing this procedure were collected from the Long Term Pavement Performance (LTPP) and North Carolina Department of Transportation (NCDOT) database. Research effort focused on investigation of the effect of the FWD load level on the condition evaluation procedures. The results indicate that the proposed procedure can estimate the pavement foundation conditions. It is also found that structurally adjusted Base Damage Index (BDI) and Base Curvature Index (BCI) are good indicators for the prediction of stiffness characteristics of aggregate base and subgrade respectively. A FWD test with a load of 66.7 kN or less does not improve the accuracy of this procedure. Results from the study for the nonlinear behavior of a pavement foundations indicate that the deflection ratio obtained from multi-load level deflections can predict the type and quality of the pavement foundation materials.