• Geotechnical Engineering
• /
• v.4 no.3
• /
• pp.43-52
• /
• 1988

The behavior of clays subjected to Repeated loading has been shown to be very different from the behavior under a single load application. Especially the behavior of pore water pressure is Qf considerable importance. The objective of this work is to experimentally study the stress-strain characteristics of clays, and this study includes the pore water pressure which is built up during the load repetition. For this study, the samples were consolidated isotropically in the triaxial cell during 24 hours, .and monotonic strain controlled triaxial test is carried out by uslng the tests of Compression failure, Cycled at failure, and Nonfailure equilibrium on remoulded samples under undrained .condition . Consequently there exists a critical level of repeated loading which seperates the behavior of a particular sample into two distinctly different patterns.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.443-445
• /
• 2004

일반적으로 기계장치나 구조물 등은 여러 가지형태의 반복하중을 받게 되며, 이러한 하중의 크기가 항복강도 이하에 있어서도 반복 피로 현상에 의해서 파괴되는 경우가 있다. 유압 피로시험기는 기계장치나 구조물의 재료나 부품에 대한 피로시험을 통하여 피로강도나 신뢰성 등을 시험하기 위한 장비이고, 본 논문에서는 유압 피로 시험기를 제어하고 데이터를 취득할 수 있는 제어시스템의 개발에 대해 서술하였다.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.6
• /
• pp.233-241
• /
• 1995

In this thesis, the fatigue tests were performed on a series of R /C beams repaired with co& crete-lmlyrner composites to investigate the fatigue bahavior. The three point loading system is used in the fatigue tests. In these tests, relations between the repeated loading cycles and mid-span deflections, number of repeated loading cycles when repaired beams were fractured, the bonding performance of repair materials were observed. On this basis, the mid-span deflections, the crack growth and failure mode of repaired R /C beams were studied. A S-N curve was drawn to present the fatigue strength of repaired beams. From the test results, it was shown that behavior of R /C beams repaired with polymer-cement series were very sirnillar to control beam about bonding performance, mid-span deflections and fatigue strength according to S-N curve drawn by the regression anlysis on the fatigue test results.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.133-152
• /
• 1999

The cyclic triaxial test was carried out to research liquefaction characteristics and sample disturbance effects of silty sand soils at the west coast in Korea. First, liquefaction in silty sand was generated when axial strain approached to $\pm10%$ of strain and behavior of pore pressure was similar to the formula suggested by Seed, Martin, and Lysmer(1975). Also, it was found that dilatancy was generated at failure. Secondly, the liquefaction evaluation methods suggested by many researchers were carried out and the results were compared. In these methods the weak depth in liquefaction was similar and the method carried out by cyclic triaxial test on remolded sample showed the least safety factor. Thirdly the stress ratio by cyclic triaxial test was compared with that obtained from SPT N-value as a kind of empirical methods. It was found that the effect of sample disturbance was relatively small when SPT N-value was less than 20, but there were large differences in safety factor and resistance of liquefaction in soil by the effects of disturbance and remolding when SPT N-value was more than 20.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.3
• /
• pp.5-12
• /
• 2009

This study presents static and dynamic strength of coal ashes collected from disposal site of power plant. Main compositions of coal ashes were bottom ashes. In order to evaluate static and dynamic characteristics of coal ash, NGI direct-simple shear tests, cyclic simple shear tests and direct shear tests were conducted. The strengths of coal ashes from those tests were compared to those of sands. Bottom ashes among coal ashes used for this study were classified as sand from the grain size distribution and show higher strength properties than the sands. For utilization of coal ashes in civil engineering project, mixing coal ashes with sandy soil using batch plant is inconvenient and the cost is higher than the spreading sand layer and coal layer alternately. In order to simulate both mixing type and layered type construction, sands and coal ashes were mixed with volume ratio 50:50 and prepared sand and coal ash layers alternately with the same volume ratio. From the tests mixed coal ashes-specimen shows slightly higher static and cyclic strength than the layered specimen at the same density. The higher strength seems due to the angular grain of bottom ashes. The cyclic stress ratio at liquefaction decreases rapidly as the number of cycle increases at mixed specimen than that of layered specimen.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.63-79
• /
• 2011

In this study relative density tests of bottom ash and standard sand were carried out. And cyclic triaxial tests for samples with the relative density of 40%, 55%, and 70% were carried out on the basis of the test results. Cyclic triaxial tests were also conducted for fines content with 55% relative density. Residual samples were divided into No.40, No.60, No.60, and No.100, and No.200. In order to avoid crashing that can happen when compaction of the sample is initiated, bottom ash was crushed using the a compact mold. In consideration of the crushing characteristics of each residual samples, the fragmentation rate increased up to 30%, which led to the adjustment of fine-grained amount to 10%, 20%, and 30%. Through the repative triaxial test in accordance with the relative density, resistant characteristics of the liquefaction of bottom ash was analyzed. Test results show that, crushing strength of bottom ash was smaller than that of standard sand, resulting in different liquefaction behavior characteristics. And we could find fines content with maximum resistant characteristics of the liquefaction.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.4
• /
• pp.25-35
• /
• 2009

This paper introduces the performance of a newly developed base isolation system made from the combination of a polyurethane disk - attached pot bearing and C-shape steel dampers. Ultimate compressive load tests, ultimate rotation tests, dynamic tests, and dynamic load repeat tests have been completed to determine dynamic characteristics and to verify performance characteristics. The experimental results are compared with the analytic results. It is determined that all requirements for bridge bearing in the specifications are satisfied, and that adequate energy dissipation has occurred. The EDC and effective stiffness estimated by tests are similar to the theoretical values.

• Computational Structural Engineering
• /
• v.2 no.3
• /
• pp.77-84
• /
• 1989

Small-scale models of reinforced concrete beam-column joints and anchorage-bond specimens were subjected to large cyclic displacements at two rates. To assess damage, free vibration tests were conducted. The reliability of the modeling techniques was established by comparison of the results for the slower rate with those obtained from the full-scale tests on prototype. The higher rate of loading caused a greater damage than that at the slower rate. This was evidenced by the measurements of the stiffness obtained from the free-vibration test. The relatively greater extent of damage appears to result from the different bond behavior at different rates of loading.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.11
• /
• pp.97-110
• /
• 2019

Piles that support offshore wind turbine structures are dominantly subjected to cyclic lateral loads of wind, waves, and tidal forces. For a successful design, it is imperative to investigate the behavior of the cyclic laterally loaded piles; the p-y curve method, in which the pile and soil are characterized as an elastic beam and nonlinear springs, respectively, has been typically utilized. In this study, model pile tests were performed in a 1 g gravitational field so as to investigate the p-y behaviors of cyclic laterally loaded piles installed in saturated dense silty sand. Test results showed that cyclic lateral loads gradually reduced the overall stiffness of the p-y curves (initial stiffness and ultimate soil reaction). This is because the cyclic lateral loads disturbed the surrounding soil, which led to the decrement of the soil resistance. The decrement effects of the overall stiffness of the p-y curves became more apparent as the magnitude of cyclic lateral load increased and approached the soil surface. From the test results, the cyclic p-y curve was developed using a p-y backbone curve method. Pseudo-static analysis was also performed with the developed cyclic p-y curve, confirming that it was able to properly predict the behaviors of cyclic laterally loaded pile installed in saturated dense silty sand.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.455-455
• /
• 2010

차세대 디스플레이로 널리 알려져 있는 플렉서블 디스플레이는 휴대하기 쉽고, 깨지지 않으며, 변형이 자유로워 현재 우리 사회에 크게 주목받고 있다. 플렉서블 디스플레이의 구현을 위해서는 기존의 유리 기반 디스플레이 소자 기술에 더하여 플렉서블 기판소재에 적용 가능한 투명전도막 기술의 확립이 필요하다. 디스플레이 산업에서 주로 사용되는 투명전도막은 ITO (indium tin oxide) 및 IZO (indium zinc oxide)와 같은 투명전도성 산화물 박막 (TCO, transparent conducting oxide)이다. 그런데 플라스틱 기판이 굽힘 환경에 놓이게 되면 그 위에 증착된 산화물 박막이 쉽게 파손될 수 있다. 따라서 플렉서블 디스플레이 기술에 있어서 변형에 따른 TCO 박막의 파괴 거동에 대한 연구가 필수적이다. 본 연구에서는 PET (polyethylene terephthalate) 기판 상에 증착된 IZO 박막의 반복 굽힘 시 계면구조 변화에 따른 파괴거동을 조사하였다. 플라스틱 기판의 사용을 위해서는 산소 및 수분의 투과 방지막이 필요하며 본 연구에서는 투과 방지막 (또는 보호막)으로서 $SiO_x$ 박막을 적용하였다. IZO 박막은 $In_2O_3$ - 10 wt% ZnO 타겟을 사용하여 RF magnetron sputtering법으로 $100^{\circ}C$ 미만에서 저온 증착하였다. 보호막으로 사용되는 $SiO_x$ 박막은 HMDSO (hexamethyldisiloxane)와 Ar 및 $O_2$ 혼합기체를 이용하는 PECVD 방법으로 합성하였다. 변형에 따른 TCO 박막의 파괴 거동을 조사하기 위하여 반복 굽힘 시험 (cyclic- bending test)을 실시하였다. 반복 굽힘 시험 중 실시간으로 IZO 박막의 전기저항 변화를 측정하여 박막의 파괴 거동을 모니터링 하였다. 시편 A (135 nm-thick IZO/PET), B (135 nm-thick IZO/ 90 nm-thick $SiO_x$/PET), C (135nm-thick IZO/ 300 nm-thick $SiO_x$/PET)에 대하여 곡지름 35mm, 1000회 반복 굽힘을 실시하여 변형 중의 전기저항 변화를 조사하였다. 그리고 굽힘 시험 완료 후, FE-SEM을 이용한 시편 표면형상 관찰을 통하여 균열생성 정도를 관찰하였다. 반복 굽힘 시험 결과, A 와 C 시편의 경우, 각각 반복 굽힘 20회, 550회에서 급격한 전기저항의 증가가 관찰되었다. 그러나 B 시편의 경우, 1000회 반복 굽힘 후에도 전기저항의 변화는 나타나지 않았다. 이와 같이 반복 굽힘에 의한 IZO 박막의 파괴 거동 변화는 IZO 박막과 기판의 계면구조변화에 기인한 것으로 해석된다. IZO 박막과 기판의 계면에 $SiO_x$ 층을 삽입함으로써 계면 접합강도가 향상되었을 것으로 추측된다. 따라서 변형에 대한 파괴 저항 특성이 우수한 투명전도성 산화물 박막의 형성을 위해서는 적절한 계면구조 제어를 통한 계면 접합 특성의 향상이 필요하다.