• Proceedings of the KTCVS Conference
• /
• 1995.10a
• /
• pp.28-28
• /
• 1995

• Journal of the Korean Society of Radiology
• /
• v.85 no.3
• /
• pp.668-675
• /
• 2024

Aortic anastomotic leak is an uncommon complication after ascending aortic replacement for acute aortic dissection. Redo-surgery is the traditional standard treatment despite high mortality and morbidity. Recently, endovascular treatment has been attempted as an alternative approach in a few case reports. Here, we present two cases of aortic anastomotic leak due to suture line dehiscence after aortic graft replacement for type A aortic dissection, which were successfully treated by coil with subsequent N-butyl cyanoacrylate embolization and an Amplatzer^TM vascular plug.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.521-529
• /
• 2017

Three-dimensional flow characteristics within a high-acceleration first-stage turbine vane passage has been investigated in a newly-built vane cascade for propulsion. The result shows that there is a strong favorable pressure gradient on the vane pressure surface. On its suction surface, however, there exists not only a much stronger favorable pressure gradient than that on the pressure surface upstream of the mid-chord but also a subsequent adverse pressure gradient downstream of it. By employing two different oil-film methods with upstream coating and full-coverage coating, a four-vortex model horseshoe vortex system can be identified ahead of each leading edge in the cascade, and the separation line of inlet boundary layer flow as well as the separation line of re-attached flow is provided as well. In addition, basic flow data such as secondary flow, aerodynamic loss, and flow turning angle downstream of the cascade are obtained.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.73-73
• /
• 2010

본 연구에서는 성장된 p-형의 단일벽 탄소 나노튜브 (SWCNT)와 폴리머 코팅으로 n-형 특성을 보이는 SWCNT의 접합으로 pn-접합 소자 어레이를 만들고 특성을 분석한 결과에 대해 발표하고자 한다. Y-cut quartz 기판에 0.1 nm 두께의 철 촉매 패턴을 만들고 화학기상증착법으로 잘 정렬된 SWCNT를 성장시킨 후, 열 박리 테이프 (thermal tape)을 이용하여 정렬된 나노선을 실리콘 옥사이드 기판에 전이한다. 전기적(electrical breakdown)으로 금속성의 나노선을 제거하고 p-형의 나노선 배열을 얻을 수 있다. 이 나노선에 국소적으로 폴리머 (polyethyleneimine: PEI) 코팅을 하여 n-형 특성을 갖는 나노선 패턴을 만들 수 있다. 이를 이용하여 만든 소자는 p-형과 n-형이 하나의 나노선 안에 부분적으로 존재하므로 연결부위의 접촉에 관한 문제가 전혀 없으며 소자를 만들기도 유용하다. 이렇게 준비된 p-형 나노선과 n-형 나노선의 접합에서 정류특성을 관찰하였다. 이러한 passive matrix 소자는 터치패드나 유기발광다이오드와 같은 다양한 소자에 응용 가능하다.

• Composites Research
• /
• v.24 no.3
• /
• pp.39-45
• /
• 2011

Adhesive joints are widely used for structural joining applications in various fields and environmental conditions. Polyurethane (PU) and Epoxy adhesives are now being used for liquefied natural gas (LNG) carriers at cryogenic temperatures. This paper presents a comprehensive evaluation of epoxy and PU adhesive bonds between Triplex sheets at normal and cryogenic temperatures. The most significant result of this study is that for all adhesives tested, there is a significant decrease in peel strength at cryogenic temperatures. However, the reasons for the decrease in peel strength for epoxy and PU adhesives differ. Consequently, PU adhesives can be considered better suited for use in applications requiring high bonding performance at cryogenic conditions, such as in LNG carriers.

• 보존과학연구
• /
• s.33
• /
• pp.57-67
• /
• 2012

The Uiseong Tapriri Five-Storied stone pagoda has occurred exfoliation, granular disintegration and discoloration by physical and chemical weathering factors with the major deterioration occurring due to efflorescence by salt. According to the results of SEM-EDS and X-ray diffraction analysis, salts consists of gypsum, taranakite. Artificial salt weathering tests were carried out using the same type of rocks as those in the stone pagoda. The test results showed that efflorescence occurred on the surface of the rock, and that exfoliation and granular disintegration occurred inside the rock due to salt crystallization.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.233.1-233.1
• /
• 2016

화학적 방법에 의한 NTE graphite의 박리 또는 전도도 개선을 위한 도핑공정을 수행할 경우, 결함 및 불순물 생성에 의해 재결정화 공정 및 순도 개선을 위한 별도의 공정을 필요로한다. 본 연구에서는 건식 방법으로써 10,000K 이상의 초고온 RF 열플라즈마를 이용하여 in-situ 방법으로 흑연의 박리, 결함 제거, 결정성 향상 및 도핑 공정을 수행하고, 도핑특성을 평가하였다. 질소 도핑을 위하여 암모니아 가스를 첨가하여 NTE graphite를 도핑 처리하였으며, 시뮬레이션을 통하여 반응기 내부의 온도분포를 파악하고, 도핑을 위한 암모니아가스가 분해되어 도핑공정이 수행될 수 있는 투입위치를 결정하였다. 질소 도핑율은 암모니아 가스의 주입위치에서의 온도 및 가스 주입 유량 등의 공정조건에 따라 변화됨을 확인하였고, XPS 분석결과 최대 14.87 atomic%의 도핑율의 결과를 얻었다.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.223-226
• /
• 2006

Computational Study of a sphere subjected to free stream flow and simultaneously subjected to spinning motion is carried out. Three dimensional compressible Navier-Stokes equations are solved using fully implicit finite volume scheme. SST(Shear Stress Transport) $k-{\omega}$ turbulence model is used. Aerodynamic characteristics being affected are studied. Validation of the numerical process is done for the no spin condition. Variation of drag coefficient and shock wave strength with increase in spinning rate is reported. Changes in the wake region of the sphere with respect to spinning speed are also observed.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2625-2630
• /
• 2008

Horseshoe vortices are formed at the junction of an object immersed in fluid-flow and endwall plate as a result of three-dimensional boundary layer separation. This study shows preliminary results of the kinematics of such horseshoe vortices around a circular cylinder with a cavity (slot) placed upstream to disturb the primary separation line. Through the cavity, no mass flow addition (blowing) or reduction (suction) is applied. The upstream cavity weakens the adverse pressure gradient before the cavity. With the upstream cavity, a single vortex is found to form immediately upstream of the cylinder whereas a typical two vortex system is observed in the absence of the cavity. Furthermore, the strength of the single vortex tends to be reduced, resulting from the interaction with the separated flow convecting directly towards the leading edge of the cylinder.

• Journal of Chest Surgery
• /
• v.29 no.3
• /
• pp.297-302
• /
• 1996

From January 1989 to July 1995, 18 patients underwent aortic repair for type A dissections. The e were 9 male and 9 female patients aged 41 to 68 years(mean, 53.8). Thirteen patients underwent the procedure during the acute period, and 5 during the chronic period. During repair of acute dissection, procedures included graft replacement of the ascending aorta only (6 patients), ascending aorta plus partial aortic arch (3), ascending aorta plus total aortic arch (2), Bentall's operation (1), and Bentall's operation plus total aortic arch (1). During repair of chronic dissection, procedures included Bentall's operation (3 patients), ascending aorta only (1), and ascending aorta plus partial aortic arch (1). During repair of the arch, antegrade cerebral perfusion was applied in 4 patients and hypothermic circulatory arrest in 3 patients. There were 4 operative deaths(22.2%), 2 of hemorrhage. and 2 of left ventricular failure in the operating room. Follow-up has been 100% completed and ranged from 2 to 53 months (mean, 17 months). One late death resulted from sepsis following secon operation. Thirteen of the survivors are doing well.