• Clean Technology
• /
• v.11 no.4
• /
• pp.171-179
• /
• 2005

Biodiesel is synthesized by transesterification of vegetable or animal oils with alcohols. Since it has similar characteristic with diesel fuel, it can be used as a fuel by mixing with diesel fuel. Moreover, it is advantageous that biodiesel can reduce air pollution emitted from fuel combustion and is produced from sustainable energy, biomass. Recently, many researchers have investigated biodiesel synthesis using supercritical methanol since it is economical due to shorter reaction time and simple separation/purification process, compared with conventional alkali- or acid-catalyzed process. By the development of biodiesel production process from waste edible oil using supercritical methanol, it can be expected to utilize potential energy resources, reduce carbon dioxide emission, and improve environmental conditions.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.6
• /
• pp.712-720
• /
• 2016

When bioethanol and water are mixed at a proper ratio, phase separation can occur because of the immiscibility of biobutanol with water. Phase separation in bioethanol blends fuels is a major problem for gasoline vehicle users due to effect of octane number and component corrosion. Thus, in this study, the phase separation of bioethanol was examined effect of bioethanol blends (E3 (3 vo.% bioethanol in gasoline), E5 and E10) in presence of water. The effect were evaluated behavior with phase separation test, simulation test of fuel tank in gas station according to water addition volume and it was investigated change of water content, bioethanol content and octane number for gasoline phase in bioethanol blends (E3, E5 and E10) every 1 week after water addition. The E3 occurred phase separation more easily than the E5 and E10 in small water contents because solubility of water on ethanol content difference in gasoline-ethanol. It was kept a initial level of water content, bioethanol content, and octane number by repeated sample replacing in simulation test of fuel tank.

• Journal of Energy Engineering
• /
• v.16 no.4
• /
• pp.194-201
• /
• 2007

HHV (Higher Heating Value) of biomass fuel is calculated by using ultimate analysis data and has been proposed by using correlation equation, and compared with the experiment the adequacy about each correlation equation with measured HHV and examined. Samples used for experiment are prepared by mixing biomass (i.e. rice husk and sawdust) with organic waste (i.e. polystyrene polypropylene and waste paper) of 10, 30, 50 wt% of composition. Ultimate analysis and measurement of HHV are respectively measured by using KS standard method. The average error value of estimated HHV results is about 880 kJ/kg(about 3.8% of measured HHV). The corresponding correlation coefficients ($R^2$) of experimental result and estimated HHV result are $0.957{\sim}0.996$.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.562-571
• /
• 2014

In these days, many countries carry out many renewable energy policies to increase the renewable energy portion and to reduce the GHG(Green House Gas). In Korea, RPS(Renewable Portfolio Standards) focused on over 500MW power producers is conducting. And they are using the bio-fuel oil to meet their RPS quota. The oil is a mixture of animal and vegetable fat or fatty acid ester of them and should satisfy some specifications to use the power generation such as viscosity, pour point, acid number. Depends on the raw materials, quality characteristics of power bio-fuel oil are changed. By adding the power bio-fuel oil, pour point, density, sulfur content and viscosity are decreased and acid number, iodine number, oxygen content are increased. In this study, we test the quality characteristic of power bio-fuel oil and the property changes by the blending ratio of power bio-fuel oil & conventional fuel oil.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.2
• /
• pp.181-187
• /
• 2003

Biodiesel fuel as an alternative fuel for diesel engine has a great possibility to solve the problems such as air pollution. It is a domestically produced, renewable fuel that can be manufactured from vegetable oils, used vegetable oils, or animal fats. In this study, the usability of biodiesel fuel derived from rice bran oil as an alternative fuel for diesel engines was investigated in agricultural diesel engine. Emissions were characterized with neat biodiesel fuel and with a blend of biodiesel fuel and conventional diesel fuel. Since the biodiesel fuel includes oxygen of about 11%, it could influence the combustion process strongly. So, the use of biodiesel fuel resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions without any increase of oxides of nitrogen. It is concluded that biodiesel fuel can be utilized effectively as a renewable and an environmentally Innocuous fuel for diesel engine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.27-32
• /
• 2008

Recently, we have a lot of interest in alternative fuels to provide energy independence from oil producing country and to reduce exhaust emissions for air pollution prevention. Biodiesel, which can be generated from natural renewable sources such as new or used vegetable oils or animal fats, may be used as fuel in diesel engine of compression ignition engine. In this paper, the test results on specific fuel consumption and exhaust emissions of neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were presented using four stroke, direct injection diesel engine, especially this biodisel was produced from soybean oil at our laboratory. This study showed that Soot and CO emission were decreased as the blending ratios of biodiesel to diesel oil increased, on the other hand NOx emission was slightly increased because of the oxygen content in biodiesel. Also, the biodiesel blends yielded slightly higher specific fuel consumption than that of diesel oil because of lower heating value of biodiesel.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.102-106
• /
• 2006

에탄올은 금속, 고무 수지를 부식시키고 열화시키기 때문에 FFV 등 알코올 대응차량이 아닌 경우 에탄올 허용도가 제한되고 있으며, 물과의 상호용해성과 흡습성으로 수분혼입에 의한 상분리가 발생하여 혼합가솔린의 유통에서의 취급에 어려움이 야기되고 있다. 또한, 에탄올은 가솔린과 혼합되면 공비현상으로 인하여 50% 유출온도가 크게 떨어지고 증기압이 7kPa 정도 상승을 초래하는 점도 간과하지 않을 수 없다. 따라서, 자동차용휘발유에 에탄올을 혼입하여 사용할 경우, 가솔린기재를 적절히 선택하여 적정품질을 유지하여야 하며 무엇보다도 에탄을 혼입농도에 따른 저장탱크와 주유기 등의 부품에의 영향과 저장시의 상분리 문제를 충분히 규명하여 유통인프라에서의 적절한 대응책이 마련되어져야 한다. 유통 인프라 대응을 위해서는 우선 생산단계에서 수분 혼입을 최소화하기 위하여 저유소의 출하지점에서 서브옥탄가솔린과 에탄올을 라인브랜딩에 의해 제조하는 방법이 가장 타당하며, 수송부문에서는 탱크로리 등의 공급라인인 파이프와 실링 재질 등에 대해서 면밀한 검토가 필요하다고 할 수 있다. 주유소에서의 대응은 에탄을 혼합연료와 직접 접촉하는 연료계 등 부품재질을 내부식성의 재질로 변환시켜야 하며, 수분혼입을 최소화하기 위한 이중탱크 설치, 지하탱크 환기구내의 대기벨브 설치 등이 필요하며, 기타, 품질 및 수분관리 대책 등도 마련되어야 할 것이다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.107-112
• /
• 2011

FFV(Flexible Fuel Vehicle) is the vehicle that can be used liberally from gasoline to E100(Ethanol 100%) for fuel. Recently, interest in the bio-fuel is increased by the environmental factors like exhaustion of the fossil fuel and ruduction of greenhouse gases. For the reason, adopting of FFV is activated in the world including North and South America. In general, bio-ethanol has highly corrosive substance in compare with gasoline. In the part of fuel system, corrosion can make a safety problem in case of fuel leakage and engine starting problem. So the fuel system of FFV have to be made of high corrosion-resistant materials. This study examined the effect of bio-ethanol on the durability properties according to component materials in FFV fuel pump motor and regulator using the High Temperature Fuel Circulation Test.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.249.2-249.2
• /
• 2010

최근의 고유가와 환경오염에 대한 대응 수단으로 수송용 바이오연료의 보급에 대한 관심이 세계적으로 높아지고 있다. 이 중 바이오디젤은 동식물성 기름으로부터 메탄올과의 전이에스테르화 반응에 의해 생산되는 경유대체 연료로서 환경 친화성과 지속가능성이 인정됨에 따라 그 생산량이 급격히 증가하고 있다. 바이오디젤의 생산량이 증가함에 따라 대두유, 유채유, 팜유 등의 원료유 가격 상승 및 수급 불안정 문제가 대두되고 있으며 식량자원과의 충돌 문제도 발생되고 있다. 이를 해결하기 위한 방안으로 유리지방산 함량이 높은 저가유지 자원(폐식용유, 폐돈지, 폐우지, soapstock, trapped grease)을 이용한 공정 개발 연구가 활발히 진행되고 있다. 본 연구에서는 비활용되고 있는 해외 열대작물 열매씨앗에서 착유한 식물성 오일의 바이오디젤 원료유로서의 사용 가능성을 검토하였다. 열대작물 오일의 물성 분석 결과 고형물, 수분, 인, 유리지방산 함량이 대두원유보다 매우 높게 나타났다. 오일 중의 인지질은 바이오디젤 제조 반응후 에스테르와 글리세린의 층분리를 방해하여 공정 효율을 감소시키고 유리지방산은 염기촉매와 결합하여 지방산염을 생성해 생산수율을 감소시키는 문제를 일으킨다. 고형물과 수분은 여과와 감압증발에 의해 쉽게 제거가 가능하였다. 15~20%의 유리지방산 함유 열대작물 오일의 전처리를 위해 균질계 산촉매와 비균질 고체 산촉매를 이용해 에스테르화 반응 효율을 조사한 결과 황산이 가장 높은 효율을 보였다. 반응표면분석법(Response Surface Method, RSM)을 적용해 메탄올과 촉매량의 2변수 에스테르화반응 최적화를 수행한 결과 메탄올 26%, 촉매 0.98%로 최적 조건이 도출되었으며 초기 산가 33mgKOH/g에서 0.98mgKOH/g으로 감소됨을 확인하였다. 전처리 정제한 오일의 물성분석 결과 고형물 0.1%, 수분 0.10%, 산가 1.0mgKOH/g, 인함량 20ppm 이하로 바람직한 원료유가 생산됨을 알 수 있었다. 제조된 원료유를 이용해 전이에스테르화 반응 최적화 실험을 RSM에 근거하여 진행한 결과 KOH 0.8%, 메탄올:오일 몰비 6.2:1, 반응온도 $60^{\circ}C$, 교반속도 200rpm, 반응시간 30분으로 나타났으며 증류 정제전 97.3%, 증류후 100.0%의 바이오디젤을 생산 할 수 있었다. 열대작물 오일의 전처리 공정은 메탄올을 과잉양으로 사용함으로 효과적인 알콜 회수 공정이 중요하다. 전처리 후 층분리를 통해 회수되는 메탄올 중의 수분함량은 2%~7%로서 이를 전처리 반응에 재사용하기 위해서는 0.3%이하의 수분함량으로 정제가 필요하다. 본 연구에서는 고가의 증류탑 형태가 아닌 단증류방식으로 2단계 내지 3단계로 0.3% 수분의 메탄올 회수 조건을 도출하였으며 파일롯 공정 설계를 진행하고 있다. 이로서 본 연구의 열대작물 오일은 저가로 충분한 물량의 확보가 가능하다면 바이오디젤 원료 자원으로서 큰 활용가치가 있는 것으로 판단된다.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.10
• /
• pp.710-716
• /
• 2013

New and renewable energy sources have drawn attention because of climate change. Many studies have been carried out in waste-to-energy field. Fast pyrolysis of waste lignocelluosic biomass is one of the waste-to-energy technologies. Bubbling fluidized bed (BFB) reactor is widely used for fast pyrolysis of the biomass. In BFB pyrolyzer, bubble behavior influences on the chemical reaction. Accordingly, in the present study, hydrodynamic characteristics and fast pyrolysis reaction of waste lignocellulosic biomass occurring in a BFB pyrolyzer are scrutinized. The computational fluid dynamics (CFD) simulation of the fast pyrolysis reactor is carried out by using Eulerian-Granular approach. And two-stage semi-global kinetics is applied for modeling the fast pyrolysis reaction of waste lignocellulosic biomass. To summarize, generation and ascendant motion of bubbles in the bed affect particle behavior. Thus biomass particles are well mixed with hot sand and consequent rapid heat transfer occurs from sand to biomass particles. As a result, primary reaction is observed throughout the bed. And reaction rate of tar formation is the highest. Consequently, tar accounts for 66wt.% of the product gas. However, secondary reaction occurs mostly in the freeboard. Therefore, it is considered that bubble behavior and particle motions hardly influences on the secondary reaction.