• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.2
• /
• pp.225-232
• /
• 2014

Purpose : The purpose of this study was to evaluate the surface and superficial dose for patients requiring postmastectomy radiation therapy(PMRT) with different treatment techniques. Materials and Methods : Computed tomography images were acquired for the phantom(I'mRT, IBA) consisting of tissue equivalent material. Hypothetical chestwall and lung were outlined and modified. Five treatment techniques(Wedged Tangential; WT, 4-field IMRT, 7-field IMRT, TOMO DIRECT, TOMO HELICAL) were evaluated using only 6MV photon beam. GafChromic EBT3 film was used for dose measurements at the surface and superficial dose. Surface dose profiles around the phantom were obtained for each treatment technique. For superficial dose measurements, film were used inside the phantom and analyzed superficial region for depth from 1-6mm. Results : TOMO DIRECT showed the highest surface dose by 47~70% of prescribed dose, while 7-field IMRT showed the lowest by 35~46% of prescribed dose. For the WT, 4-field IMRT and 7-field IMRT, superficial dose were measured over 60%, 70%, and 80% for 1mm, 2mm, and 5mm depth, respectively. In case of TOMO DIRECT and TOMO HELICAL, over 75%, 80%, and 90% of prescribed dose was measured, respectively. Surface and superficial dose range were uniform in overall chestwall for the 7-field IMRT and TOMO HELICAL. In contrast, Because of the dose enhancement effect with oblique incidence, The dose was gradually increased toward the obliquely tangential angle for the WT and TOMO DIRECT. Conclusion : For PMRT, TOMO DIRECT and TOMO HELICAL deliver the higher surface and superficial doses than treatment techniques based linear accelerator. It showed adequate dose(over 75% of prescribed dose) at 1mm depth in skin region.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.1 no.1
• /
• pp.117-129
• /
• 1990

35 children(17 boys, 18 girls) with Recurrent Abdominal pain(RAP) without apparent organic causes, referrd from pediatric department of Seoul National University Children's Hospital were studied during 1988. 7. 1 ${\sim}$ 1989. 2. 28. The aims of this study are to examine clinical characteristics of the patients with RAP, to find possible factors influencing the onset and the course of the disorder, to evaluate the psychological status and the relationship with psychiatric diagnoses. The study subjects were compared with the age and sex matched control subjects on measures of social and school functioning, family-environment, behavior traits by CBCL and parent-environment rating scale. All patients and their mothers were interviewed by a child psychiatrist. The results were as follows ; 1) Abdominal pain was found to be more frequent when with a care taker, and related with traumatic life stresses such as separation from parents, death of family members. 2) Family members of the patients with RAP also had a high rate of a history of gastrointestinal dysfunctions with could not be attributed to organic etiologies. 3) Among 35 patients with RAP, 16 were diagnosed as psychiatric disorders. They were adjustment disorders (4), overanxious disorders (4), depression (2), tic disorders (2), attention deficit disorders (2), separation anxiety disorders (1), enuresis (1). 4) On CBCL, the patients with RAP were more internalized, socially less competent and less active compared with the control subjects. 5) According to the parent-environment rating scale, the patients with RAP had more conflicts with their parents about control issues. Family members of the patients with RAP were socially less competent and less abjustable. The parents of the patients with RAP were more affectionate and spent more time with their children but they were unfair and vague on instruction and discipline.

• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.469-477
• /
• 2016

To evaluate the $CO_2$ storage capacity for the reservoir rock, the laboratory scale technique to measure the amount of $scCO_2$, replacing pore water of the reservior rock after the $CO_2$ injection was developed in this study. Laboratory experiments were performed to measure the $scCO_2$ displacement efficiency of the conglomerate and the sandstone in Janggi basin, which are classified as available $CO_2$ storage rocks in Korea. The high pressurized stainless steel cell containing two different walls was designed and undisturbed rock cores acquired from the deep drilling site around Janggi basin were used for the experiments. From the lab experiments, the average $scCO_2$ displacement efficiency of the conglomerate and the sandstone in Janggi basin was measured at 31.2% and 14.4%, respectively, which can be used to evaluate the feasibility of the Janggi basin as a $scCO_2$ storage site in Korea. Assuming that the effective radius of the $CO_2$ storage formations is 250 m and the average thickness of the conglomerate and the sandstone formation under 800 m in depth is 50 m each (from data of the drilling profile and the geophysical survey), the $scCO_2$ storage capacity of the reservoir rocks around the probable $scCO_2$ injection site in Janggi basin was calculated at 264,592 metric ton, demonstrating that the conglomerate and the sandstone formations in Janggi basin have a great potential for use as a pilot scale test site for the $CO_2$ storage in Korea.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.42 no.4
• /
• pp.403-412
• /
• 2016

The tight junction, one of Intercellular junctions, performs a variety of biological functions by bonding adjacent cells, including the barrier function to control the movement of the electrolyte and water. Recent studies have revealed that unusual expression of tight junction-related genes have been shown to be related in cancer development and progression. Recently, there are many reports that control of tight junction proteins expression is closely related to the skin moisture. In this study, we are focusing on the regulating mechanism of tight junction-associated genes by the steviol and its derivatives. Steviol, used as a sweetner, is known to chemical compound isolated from stevia plant. The MTS (3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium, inner salt) assay was carried out in HaCaT cells (human keratinocyte cell line) in order to determine the cytotoxicity. As a result, while steviol showing cytotoxicity from $250{\mu}M$, steviol derivatives are not cytotoxic more than $250{\mu}M$ concentration. We have observed a change in the tight junction protein via quantitative real-time PCR. Claudin 8 among tight junction proteins is only significantly reduced up to 30% in the presence of steviol. In addition, cell migration was inhibited by steviol, not by stevioside and rebaudioside. Finally, we could observe that steviol, not stevioside and rebaudioside, is able to increase the skin barrier permeability through the transepithelial electric resistance (TEER) measurements. These results suggest that the steviol and its derivatives are specifically acts on the tight junction related gene expression, but steviol derivatives are more suitable as a cosmetic material.

• The Journal of the Petrological Society of Korea
• /
• v.27 no.3
• /
• pp.139-151
• /
• 2018

The Songgang-ri area, Cheongsong-gun, which is located in the Sobaeksan province of Yeongnam Massif near the southwestern boundary of Yeongyang subbasin of Gyeongsang Basin, consists of age unknown metamorphic rocks (banded gneiss, granitic gneiss, limesilicates) and age unknown igneous rock (granite gneiss) which intrudes them. This paper researched the geological structures of the Songgang-ri area from the geometric and kinematic features and the developing sequence of multi-deformed rock structures in the geological outcrops exposed about 170 m along the riverside of Yongjeoncheon in the eastern part of Songgang village, Songgang-ri. In the Songgang-ri geological outcrops are recognized three times (Fn, Fn+1, Fn+2) of folding, three times (Dk-I, Dk-II, Dk-III) intrusion of acidic dykes, one time of faulting, which are different in deformation and intrusion timing each other. These geological structures are at least formed by five times (Dn, Dn+1, Dn+2, Dn+3, Dn+4) of deformation. The Dn deformation is recognized by Fn fold which axial surface is parallel to the regional foliation. The Dn+1 intruded the (E)NE trending Dk-I dyke in the earlier phase and formed the NW trending Fn+1 fold in the later phase under compression of (E)NE-(W)SW direction. There are tight, isoclinal, intrafolial folds, boudinage, ${\sigma}$- or ${\delta}$-type boudins, asymmetric fold, C' shear band as the major deformed rock structures. The Dn+2 intruded the (N)NW trending Dk-II dyke in the earlier phase and formed NE trending Fn+2 fold in the later phase under compression of (N)NW-(S)SE direction. There are open fold and folded boudinage as those. The Dn+2 intruded the Dk-III dyke which cuts the Dk-I and Dk-II dykes and the axial surface of Fn+2 fold. The Dn+3 formed the left-handed reverse oblique-slip fault of NNE trend in which hanging wall moves into the SSE direction. Considering in that such five times of deformation recognized in the Songgang-ri geological outcrops are closely connected to the distribution and geological structure of the constituents in the more regional area as well as Songgang-ri area, the research result is expected to play a great data in clarifying and understanding the geological structure and its development process of the surrounding and boundary constituents of the Yeongnam Massif and Gyeongsang Basin.

• Journal of Food Hygiene and Safety
• /
• v.33 no.4
• /
• pp.272-279
• /
• 2018

The high pressure processing (HPP) is a technology which can preserve the quality of foods, such as the fresh taste, incense, texture, vitamin content, and so on, by minimizing the heating process. It does so by applying an instantaneous and uniform pressure that is the same as the water pressure that is 60 km deep in the sea. HPP is a technology that can inhibit food poisoning and spoilage caused by microorganisms and is currently an actively studied area. In this study, we investigated the effects of a high pressure treatment (0, 4, 6 min) on sliced ham, which is a typical meat product, at 600 MP a were tested for their effect on freshness. Moisture contents varied from 48 to 69%, salinity varied from 1.07 to 1.11%, and the pH decreased from 6.4~6.5 to 6.1~5.15. However, there was no difference between the control and treatment groups. General bacteria stored at $20^{\circ}C$ after hyper-pressure treatment were found to have no significant microorganisms in all groups until 4 weeks. but exceeded $10^5$ in control group and HPP 6 min treatment group from 5 weeks, At week 7, it was found to exceed $10^6$. The results indicate it was not possible to ingest food in the 4-and 6 minute treatment groups. Coliform was not observed in all groups despite observing for a total of 7 weeks at $20^{\circ}C$ weight test. VBN, a method used to determine the protein freshness of meat, showed a VBN value of less than 1 mg% until the fourth week and a value of 1 to 2 mg% after 5 weeks. The TBA was used as an index of the degree of fat acidosis in the meat tissues. The results showed it was below 0.18 mgMA / kg until the end of 7 weeks; this value was within the range for fresh meat, and there was no difference in treatment group. In this experiment, deformation of the packaging material did not occur and no swelling occurred due to the generation of gas. It is believed that the basic preservation effect was achieved only by blocking with the air due to the close contact of the packaging material.

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.131-140
• /
• 2003

The purpose of this study was to evaluate clinical applications of electroplating method through investigation of the physical properties of orthodontic rectangular wires according to varying their cross section. For the study, it was accomplished to electroplate the 0.016-inched orthodontic rectangular stainless steel wire. The cross section of stainless steel orthodontic rectangular wire increased from $0.016{\times}0.016inch\;to\;0.017{times}0.017inch$ by electroplating. The wire was heat treated to improve an adhesion between the wire and electroplated metal. h three-point bending test and torsion test were conducted in order to compare physical properties among three wire groups; $0.016{\times}0.016wires(group 016),\; electroplated\;0.016{\times}0.016wires(group\;016P)\;and\;0.017{\times}0.017$ wires (group 017). Through the investigations of each wire group, following results were obtained 1. At three-point bending test, the group Ol6P showed higher tendency in the degree of stiffness, yield strength and ultimate tensile strength than the group 016. Stiffness and ultimate tensile strength showed statistically significant differences between two groups at three-point bending test (p<0.05). 2. Stiffness, yield strength, and ultimate tensile strength of the group 016P showed lower tendency than those of the group 017 Stiffness showed statistically significant differences between two groups at three-point bending test (p<0.05). 3. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 016P showed higher tendency than those of the group 016. All measurements showed statistically significant differences between two groups alter torsion test (p<0.05). 4. Torque/twist rate, yield torsional moment, and ultimate torsional moment of the group 0166P showed lower tendency than those of the group 017. Yield torsional moment, and ultimate torsional moment showed statistically significant differences between two groups after torsion test (p<0.05).

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.121-130
• /
• 2003

The purpose of this study was to evaluate the possibile clinical application of electroplating to increase diameter of an orthodontic wire, through examining the change of physical properties. The diameter of stainless steel orthodontic wire was increased from 0.016 inch to 0.018 inch by electroplating in a bath of nickel sulfate 100g/L, nickel chloride 60g/L, boric acid 30g/L, and sodium chloride 50g/L, under the conditions of 1.7V, $25\~29^{\circ}C\;and\;3.1\~3.3pH$. During the electroplating, the rate of diameter increase was measured every minute. To investigate uniformity, the diameter was measured at three different locations of each wire specimen aster electroplating. An X-ray diffraction test was performed to analyze the nature of the electroplated metal. Following heat treatment to improve adhesion between the wire and electroplated metal, a three-point bending test was conducted to compare stiffness, field strength, and ultimate strength among four wire groups; 0.016 inch, electroplated 016, electroplated and heat-treated 016, and 0.018 inch wires. Through the comparison of each wire group, following results were obtained. 1. In the load-deflection graph, the curve of the electroplated group was Placed between that of the 0.016 inch group and the 0.018 inch group, and the owe was closer to the 0.018 inch group by heat treatment. 2. In the electroplated and heat-treated 016 wire group, the values of stiffness, yield strength and ultimate strength showed higher tendency than in the original 0.016 Inch group. Stiffness and ultimate strength showed statistically significant differences between two groups. 3. Stiffness, yield strength, and ultimate strength of electroplated wire presented lower values than those of 0.018 inch wire group. 4. Stiffness, yield strength, and ultimate strength of electroplated and heat-treated wire showed higher tendency than those of electroplated wire group, and ultimate strength showed statistically significant difference between two groups. 5. After electroplating, the difference in diameter between the three locations was within $0.1\~0.3\%$ variation, and showed no statistical significance.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.37 no.4
• /
• pp.72-85
• /
• 2009

This study attempts to examine the principles of landscape composition for a 'Suhwon(書院)' and the meaning and value of its traditional landscape architecture, in order to apply the results to the design of modern landscape architecture. A 'Suhwon' is a vital space containing the form and meaning of human activity. This study analyzes the characteristics of landscape composition in the construction of the Namgea Suhwon, located in Hamyang, by examining the form and meaning of its area and composition. The Namgea Suhwon was constructed with a suitable configuration and harmony in a good location, neither field nor mountain, and which encompasses transcendence and a return after passage through a period of birth and abundance. Its appearance means 'life existence and hidden death(生居死幽)'. Its spatial system is a reflection of the idea of Samshinoje(三神五帝: The three abilities of Providence and its five subjects) connected with Ilsangje -Samshin -Ohje. It was built based on the idea of Biryebudong(非禮不動) meaning that one should follow only good decorum and avoid discourtesy, complying with "the frame of decorum" developed by the family rites of Chu Hsi. The environmental design of the Namgea Suhwon was interrupted by the material confrontation between mountains and water and a binary code system, such as front to rear, length to breadth, and movement to stillness. The design did not adhere to stiff axes, but pursued the harmonic principles of asymmetric balance in the building and the yard, which are very naturalistic. The name 'Namgea Suhwon' is closely related with the view of placement(置) and harmony(和), which are unified with the function and meaning formed by connecting Sung Confucianism with the Pungsu-Sasinsa structure in the layout of the grounds. When examining the D/H ratio of the building and yard, it can be seen that the spaces of Ganghak, Yusang and Jehyang were built appropriately, according to the natural characteristics of each space, such as a sense of openness, enclosure, tension, relief, enhancement, and hierarchical order. The spaces also reflect human scale concepts that take advantage of auditory features. The transition process after the construction of 'Namgea Suhwon' reveals the intentions of the builder to create an ecological landscape composition based on Placement and Harmony. Placement embodies' a purposeful space in which nature and the building are connected naturally, 'incomplete open space pursuing completion', and 'potential beauty in which tension and relaxation are repeated'. Harmony embodies 'order and continuity having a sense of unity with the natural environment' and the 'sharing of daily life and memory'. 'Namgea Suhwon' contains many ideas for landscape planning, land use and the design of a campus environment.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.877-887
• /
• 1996

The ideal membranes for membrane-covered oxygen probes system should be selectively permeable for oxygen and chemically inert, and have good mechanical strength. Polysulfone(PSf) was selected to develop the membrane for membrane-covered oxygen electrodes system. PSf membranes have properties such as good reproducibility, good mechanical strength, chemical inertness, and high heat resistance. PSf membranes were cast from polymer solution on the glass plate at constant temperature, and casting solvents used were tetrahydrofuran(THF), methylene chloride, and N-methyl-2-pyrrolidone(NMP). Tricresyl phosphate(TCP) as plasicizer was added to PSf to increase the softness of membrane. The permeation characteristics were observed for pure oxygen and nitrogen through pure PSf membranes by variable volume method and membrane-covered electrode system. The permeability coefficients of oxygen and nitrogen measured by variable volume method were slightly decreased with increasing of upstream pressure. The permeation properties of PSf membrane using methylene choride as casting solvent were not affected by the PSf amount of polymer solution. The permeability coefficients of oxygen and nitrogen for PSf membrane containing TCP were very slightly lower than those for pure PSf membrane, but ideal separation factors were slightly higher. The flexibility of PSf membrane containing 2wt% TCP was better than that of pure PSf membrane. It was expected that this increase in flexibility would solve the difficulty of fixing the membrane to the cathode. The membrane-covered oxygen probes system was composed of anode, cathode and electrolyte. The type of the anode was Ag/AgCl half-cell, that of cathode was Ag, and the electrolyte was 4N KCl solution. The result of sampled current voltametry for PSf membrane showed the plateu region at -0.3V~-1.0V. The correlation coefficient of oxygen partial pressure versus current for PSf membrane was relatively high, 0.99949. It was concluded that PSf membrane was the good candidate for the membrane-covered oxygen probes system.