• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.51.2-51.2
• /
• 2005

• 대한기계학회논문집B
• /
• 제28권12호
• /
• pp.1549-1556
• /
• 2004

We have deigned, fabricated and compared four different types of static chaos microfluid mixers, including the mixers using straight channel flow, microblock-induced alternating whirl flow, microchannel-induced lamination flow, and combined alternating whirl-lamination flow. Among them, the alternating whirl-lamination (AWL-type) mixer, composed of 3-D rotationally arranged microblocks and dividing microchannels fabricated by conventional planar lithography process, is effective to reduce the mixing length over wide flow rate ranges. We characterize the performance of the fabricated mixers, through the flow visualization technique using phenolphthalein solution. We verify that the AWL-type microfluid mixer shows the shortest fluid mixing length of 2.8mm∼5.8mm for the flow rate range of Re=0.26∼26 with the pressure drop lower than 5kPa. Compared to the previous mixers, requiring the mixing lengths of 7∼17mm, the AWL-type microfluid mixer results in the 60% reduction of the mixing lengths. Due to the reduced mixing lengths within reasonable pressure drop ranges, the present micromixers have potentials for use in the miniaturized Micro-Total-Analysis-Systems($\mu$TAS).

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.44.2-44.2
• /
• 2005

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2495-2500
• /
• 2008

We simulated the mixing characteristics in micro T-channel using Lattice Boltzmann Method. We studied the relation a mixing length and pressure-drop due to inlet and outlet ration in Reynolds number 0.5, Peclet number 500 and Schmidt 1000. The ratio of a down-inlet to up-inlet was $0.5{\sim}1.5$ times, up-inlet to outlet was $1{\sim}3$ times and outlet length was 250 times to up-inlet. The mixing length decrease linearly as outlet ratio decreased, and pressure-drip increase non-linearly. Initial stage of micro channel mixture was fast by down-inlet ratio, however, the mixing length is not influence.

• 대한기계학회논문집B
• /
• 제30권5호
• /
• pp.430-437
• /
• 2006

The mixing effect is studied by comparing rotating and oscillating stirrers in the micro channel. The cases of Re=10 to 80 with various stirring speeds are considered to analysis the effect of Re and stirrer speed for the mixing. Under Re=20, the oscillating stirrer represents better mixing rate than the rotating stirrer up to the critical stirrer speed which has a maximum efficiency. Over Re=30, the results of oscillating and rotating stirrer show that the faster the stirrer speed, the higher the mixing effect within the concerned stirrer speed range and the oscillating stirrer keeps the higher mixing rate. It was found that the mixing effect is a function which has an optimum of the Reynolds number and the stirrer speed. The D2Q9 Lattice Boltzmann Method is used due to the merits of calculation for the unsteady flow with moving boundary.

• 한국공작기계학회논문집
• /
• 제17권5호
• /
• pp.95-100
• /
• 2008

An active micro-mixer, which is composed of an oscillating micro-stirrer in the micro-channel to provide effective mixing was optimized. The effects of molecular diffusion and disturbance by the stirrer were considered with regard to two types of mixer models: the simple straight micro-channel and micro-channel with an oscillating stirrer. Two types of mixer models were studied by analyzing mixing behaviors such as their interaction after the stirrer. The mixing was calculated by Lattice Boltzmann methods using the D2Q9 model. In this study, the time-averaged mixing index formula was used to estimate the mixing performance of time-dependent flow. The mixing indices of the two models were compared. From the results, it was found that the mixer with an oscillating stirrer was much more enhanced and stabilized. Therefore, an approximate optimization of an active micro-mixer with an oscillating stirrer was performed using Kriging method with OLHD(Optimal Latin Hypercube Design) in order to determine the optimal design variables. The design parameters were established as the frequency, the length and the angle of the stirrer. The optimal values were obtained as 1.0346, 0.66D and $\pm45^{\circ}$, respectively. It was found that the mixing index of the optimal design increased by 88.72% compared with that of the original design.

• Journal of Biosystems Engineering
• /
• 제21권2호
• /
• pp.146-154
• /
• 1996

농약의 직주입 혼합방식은 작업자의 안전에 기여하며 남은 농약은 용기와 함께 수거되어 재사용 되므로 환경보전 및 경제적 이점이 있다. 그러나 주입식 방제기의 분관내 농약혼합액이 노즐에 이르는 시간까지의 유동특성인 지연시간은 농약 살포량에 오차를 유발한다. 본 연구는 이 지연시간이 미치는 실제 살포오차의 정도를 파악하려 시뮬레이션을 행하였다. 시뮬레이션의 결과에 의하면 오차는 상당히 심각한 것으로 판단되었으며 지연시간을 단축하려는 여러 방법을 검토하였다. 분관의 직경을 줄여 유동속도를 빠르게 하거나, 혼입 농약의 양을 일정하게 유지하며 방제속도를 가능한 목표속도에 맞추는 방법 등은 약간의 오차를 줄일 수 있을 뿐이었고, 농약을 각 노즐에 주입함으로써 오차를 최소화할 수 있으나 미소계략의 문제를 내포하였다. 따라서 농도의 변화에 따른 지연시간을 없앤 직주입 총유량 제어방식을 통하여 노즐 배출유량을 방제속도의 변이에 따라 보상하며 비례적으로 농약을 주입하여 농도를 일정하게 유지할 수 있을 것으로 판단된다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.45-48
• /
• 2002

To investigate the flow related to the mixing, micro PIV measurements were performed in the middle plane of the channel. A passive micro mixer analyzed in this work has been designed in the shape of a three-dimensional microchannel and fabricated with PDMS molding process by KAIST. The mixing performance was evaluated for different flow rates using phenolphthalein and sodium hydroxide solutions. Results show that mixing is enhanced by the increase of flow rate, which yields stronger secondary flows with helical streamlines.

• 대한기계학회논문집B
• /
• 제30권2호
• /
• pp.144-152
• /
• 2006

In order to consider the effect of Karman vortex for mixing, mixing indices are calculated for 4 models of micro channel flows driven from the combinations of a circular cylinder and a oscillating stirrer. And their results are compared to that of a simple straight micro channel flow(model I). The mixing rate is improved 5.5 times by Karman vortex (model II) and 11.0 times by the stirrer(model III) respectively. In case of successive mixing by the cylinder and the stirrer(model IV), $27\%$ of shortening the channel length for the complete mixing as well as 1.37 times improvement of mixing efficiency then model III. And then, variation of mixing indices are much stable comparing with the others. Thus, it is found that the Karman vortex plays a good role as a pre-mixing method. The D2Q9 Lattice Boltzmann methods are used.

• 대한기계학회논문집B
• /
• 제35권6호
• /
• pp.633-640
• /
• 2011

본 연구에서는 고온의 미소농도구배 조건에서의 에지화염의 안정화 및 화염 강도 변화를 실험적으로 관찰하였다. 실험 연소기는 크게 혼합기가 투입되는 슬롯과 석영 채널 및 채널 내부 가열을 위한 추가적인 예혼합 연소기로 구성되어 있다. 실험의 정확성을 위해 각 경계 조건에 대한 정량적인 검증 절차가 수행되었다. 결론적으로 연료 농도 구배의 정량적인 제어와 질소 희석비율을 조절하여 고온의 조건에서도 에지화염을 임의의 위치에 안정화 시킬 수 있었다. 에지화염 내부에 존재하는 확산화염의 화염 강도가 채널 내부의 온도증가에 따라 증가하고 질소의 희석비율 증가에 따라 감소하는 것을 보였다. 연료에 따른 화염 강도 변화를 살펴본 결과 프로판의 경우가 메탄에 비해 강도 변화율이 큰 것을 알 수 있었다.