• The Journal of Engineering Geology
• /
• v.31 no.2
• /
• pp.149-163
• /
• 2021

Damage characteristics of granite, marble and sandstone whose properties were different were investigated by uniaxial compression test and cyclic loading-unloading test. Strength, elastic constants and damage threshold stresses were measured by uniaxial compression test and were compared with those measured by cyclic loading-unloading test. Average rock strengths measured by cyclic loading-unloading test were either lower than or similar with those measured by uniaxial compression test. Rocks with high strength and low porosity were more sensitive to fatigue than that with low strength and high porosity. Although permanent strains caused by cyclic loading-unloading were different according to rock types, they could be good indicators representing damage characteristics of rock. Damage threshold stress of granite and marble might be measured from stress-permanent strain curves. Acoustic emissions were measured during both tests and felicity ratios which represented damage characteristics of rocks were calculated. Felicity ratio of sandstone which was weak in strength and highly porous could not be calculated because of very few measurements of acoustic emissions. On the other hand, damage threshold could be predicted from felicity ratios of granite and marble which were brittle and low in porosity. The deformation behaviors and damage characteristics of rock mass could be investigated if additional tests for various rock types were performed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.8
• /
• pp.2431-2435
• /
• 1996

In order to determine the effects of hydrostatic pressure on the mechanical behavior of graphite fiber reinforced composites, the modulus, fracture stress(maximum stress), and fracture strain of graphite/epoxy composites have been determined as a function of pressure. Composite specimens used in this study were 90-deg unidirectional and had a 60% fiber volume fraction. Compressive tests under five different pressure levels were conducted. The result showed the modulus measured from as initial slope of stress-strain curve increased bilinearly with pressure with a break at 200 MPa. It was also found that fracture stress and fracture strain increased in a linear fashion with pressure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.5
• /
• pp.864-872
• /
• 1992

Two double-exposure holograms are made in the different view angle at the same time, using laser, by overlapping before and after the static deformation. These images are transfered to the computer. The fringe patterns of holograms are recognized by image processing and each component of the displacement and strain at each point of the specimen is obtained by vector analysis, and the results were presented in the graphical form. For the verification of all the ment process, the two experimental cases, the in-plane displacement by tension load and the out-of-plane displacement by bending load, are measured. These results are compared with the exact solution.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.4
• /
• pp.477-486
• /
• 1986

본 연구에서는 SM20C를 모재로 하여 입경의 크기가 다른 3종의 복합조직강을 제작 동일한 분위기에서 저 및 고사이클 전영역에 걸쳐 피로특성을 검토하고져 한다. 제일보는 그 중 저사이클특성에 대한 보고이다. 일반적으로 저사이클 피로현상은 재 료가 탄소성 상태하에서 전위, 미소크랙, 보이드(void) 등의 인자가 복합적으로 작용 하여 발생함으로 변형률속도, 제어파형, 온도, 시험방법 및 분위기에 따라 많은 영향 을 받는다. 따라서 본 연구에서는 두가지 실험방법을 사용, 응력-변형율거동을 검토 복합조직강의 피로특성과 입경크기가 피로거동 및 강도에 미치는 영향을 비교 고찰하 였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1373-1380
• /
• 1992

The local cyclic strain distribution near the crack tip has been investigated by the fine Dot Grid Strain Measurement Method, which had been suggested strain measurement method to resolve experimental difficulties by authors. It has been found that the magnitude of the local cyclic strain distribution(.DELTA..epsilon.$_{eq}$ )near a crack tip has been varied by the applied cyclic load level and material, but the shape of the local cyclic strain distribution near the crack tip has been experimentally scrarcely altered : that is .DELTA..epsilon.$_{eq}$ = .DELTA.A.f(.theta.). $r^{-1}$ . Consequently, the local cyclic strain field near the crack tip could be favorably characterized by a single parameter fatigue strain intensity factor .DELTA.A. In addition, with the viewpoint that .DELTA.A depends on material and load level, .DELTA.A has been applied to evaluate the fatigue crack propagation rate and usefulness of the result has been considered. As a result, it has been ascertained that .DELTA.A has been a useful parameter to evaluate the fatigue crack propagation rate.

• Explosives and Blasting
• /
• v.22 no.2
• /
• pp.33-43
• /
• 2004

The six grades weathering system is normally used in weathered rock classification. In this study. fresh and weathered rock block of grade I to V were sampled in Jang-soo ana but samples of the grade VI was omitted from this study. The variation quantities of chemical weathering indices with weathering degree are smaller than those of physical and mechanical properties. Increase of Weathering degree is well indicated by physical and mechanical properties such as strength, hardness, ultrasonic velocity and slake durability result. Especially, absorption and porosity ratio is a good indicator. As weathering proceeds. a number of the cracks affect the rock deformation. Therefore, stress-strain curves of weathered rocks in unconfined state are quite different from ones of fresh rocks.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.5-5
• /
• 1997

고체추진제에 대한 비선형 점탄성 구성모델이 제시되었다 추진제 손상의 원인으로서 바인더와 AP 충전제사이의 접착분리를 고려하였으며, 점탄성 드웨팅판별식이 개발되었다. 손상에 의한 추진제의 연화는 모듈러스 저하로서 취급되었으며, 모듈러스저하 계산시에 드웨팅에 의하여 야기된 미소진공구의 모듈러스는 유한 상수로서 간주되었다. 바인더와 AP 충전제사이의 접착에너지는 180$^{\circ}$ 접착박리시험으로 측정하였다. 반복하중시의 비선형성은 전단변형률 불변량의 함수로서 고려되었다. 이 구성모델은 여러 하중조건에 대한 시편실험과 비교되어 잘 일치하였으며, 복잡한 미시구조학적 역학기구 없이 간단하게 고체 추진제의 거동을 예측할 수 있게 한다.

• Geophysics and Geophysical Exploration
• /
• v.10 no.3
• /
• pp.203-210
• /
• 2007

As a part of basic studies on monitoring of landslides and slope stability using SP measurements, micro-electric potentials of rock samples were measured accompanied with the rock failure by a uniaxial loading test were measured. The measurement system consists of a 8 channel A/D converter with 24 bit resolution, uniaxial loading tester, strain gages and 4 sets of electrode attached to a rock sample. Rock samples of granite, limestone, and sandstone were tested. Also, mortar samples were tested in order to monitor electric-potentials of a uniform sample. Micro-electric potentials were detected in all saturated samples and the strength of them increased as the loading force increased. Sandstone samples showed the largest strength of micro-electric potential and it followed limestone and granite samples, which indicates a positive relationship with porosity of rocks. The mechanism generating these micro-electric potential can be explained in terms of electro-kinetics. In case of dry samples, micro-electric potential could be observed only in sandstone samples, where piezoelectric effect played main role due to high contents of quartz in sandstone samples. We found that biggest micro-electric potentials were observed at the electrodes near the crack surface of rock samples. This is very encouraging result that SP monitoring can be applied to predicting landsliding or to estimate collapsing position combining with monitoring of acoustic emissions.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.139-146
• /
• 2001

Undrained triaxial tests were peformed for a weathered soil, which includes local measurement using LVDT The behavior from small In large strain conditions could be evaluated consistently through a triaxial test, The stress-strain relationship of undisturbed samples were compared with the disturbed and the shear moduli in the small strain level had the almost same values. Especially the shear moduli were mostly affected by the initial condition of water contents. An anisotropic hardening model based on the total stress concept could predict the stress-strain relationship accurately, which makes it possible to analyze the geotechnical problem reasonably for the weathered soil.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.08a
• /
• pp.84-85
• /
• 2000

굴절률이 외부보다 큰 원통(cylinder)이나 구(sphere)는 경계면에서의 빛의 전반사(total internal reflection)에 의해 손실이 매우 적은 high-Q 공진기가 될 수 있음이 잘 알려져 있다. 이때 발진되는 공명모드를 '속삭이는 회랑 모드(whispering gallery mode: WGM)'라고 하며, 색소가 첨가된 고체 구, 액체 방울, 액체 제트 등의 미소 공진기나 반도체 microdisk 등에서 구현되었다. 이러한 미소공진기는 일반적으로 완전한 구나 실린더의 형태로 만들어지는데, 이 경우 공진 모드를 analytic 하게 구할 수 있고 기하 광학적으로 비교적 간단히 이해할 수 있다. 하지만 최근 Nockel 등에 의해 공진기에 변형을 가한 경우 여러 가지 재미있는 현상이 일어날 수 있다는 것이 밝혀졌다$^{(1, 2)}$ (중략)