• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.1
• /
• pp.10-17
• /
• 1999

The present work presents condensation heat transfer and pressure drop data for the flow of R-12 in flat extruded aluminum tubes with small hydraulic diameters. The tube outside dimensions are $18mm(width){\times}1.7mm(height)$. Three types of internal geometry with the same outside dimensions are tested : sample 1 (7 tube holes), sample 2 (13 tube holes) and sample 3 (7 tube holes, micro-fin). The overall heat transfer coefficient is obtained for air-to-refrigerant heat transfer, and the Wilson plot method is used to determine the heat transfer coefficient for refrigerant flow. The sample 2 and sample 3 show significantly higher performance than sample 1. The heat transfer rates for the sample 2 and sample 3 are 9% and 12% higher, respectively, than sample 1. The friction factors for the sample 2 and sample 3 are 11.9% and 2.4% higher, respectively, than sample 1.

• Transactions of the Society of Information Storage Systems
• /
• v.9 no.1
• /
• pp.1-4
• /
• 2013

Graphene and Graphene oxide have intense interest in fields such as physics, chemistry, and materials science, among others. They are the promising material for solving the current limitation that organics have barely luminescence. We observed variation of photoluminescence on graphene oxide based solution with Gold nanoparticle. Gold nanoparticles lead to shift the peak wavelength of graphene oxide and to enhance the photoluminescence intensity totally. This shows the possibility that control the luminescence property of graphene oxide by adding gold nanoparticle.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.1
• /
• pp.97-103
• /
• 2024

In this paper, the difference between the S-parameter and the characteristic impedance according to the structural change of the fine pitch coaxial socket was analyzed. A pitch of the probe pin was applied to 0.20mm, and ground pins of different conditions were placed on each of the five signal pins. Insertion loss and reflection loss were analyzed for the coaxial socket of normal structure and the two sockets of the proposed structure. In addition, the difference in characteristic impedance was analyzed using time domain reflectometry. Through the analysis, it was confirmed that the characteristic impedance was improved applying the new structures of the socket at the same pitch

• Journal of the Korean Institute of Gas
• /
• v.20 no.2
• /
• pp.10-15
• /
• 2016

This paper is to analyze and study the failure examples of refrigerant gas in automotive air conditioner. The first example, the air conditioner compressor continually operated that the refrigerant was leaked in air conditioner system. By lubrication shortage, the piston was partially sticked on cylinder of air conditioner compressor inner part. This was caused the phenomenon of engine operation trouble by load increasing with engine rpm variation during engine running. The second example, it sought the fact that the air conditioner refrigerant gas was leaked from air conditioner compressor to condenser high pressure pipe toward rear air conditioner checking with the lines of air conditioner. The third example, the refrigerant gas of air conditioner found that was leaked imperceptible from condenser inner by crack that was generated on the fins of air conditioner condenser. Therefore, the air conditioner system that maintain the air conditioner by decreasing the in-car temperature must meticulously manage to not leak the air conditioner refrigerant gas.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.11a
• /
• pp.63-63
• /
• 2000

저급의 고지 원료를 두께 방향으로 고온 압착을 가하여 건조함으로써 전반적인 종이 물성 을 향상시키는 콘디벨트 건조 방식은 70년대 중반부터 80년대에 이르는 10여년에 걸친 개발 과정을 거쳤으며 90년대에 들어서 핀랜드의 Inkeroinen에 위치한 V alemt- Tarnpella의 연구 소에 최초의 파일로트 설비가 설치되었으며 그 후 1996년에는 핀랜드 ENSO사의 P Pank밟oski 판지공장에 설치됨으로써 세계 최초의 상업생산설비를 이루게 되었다. 기존의 실린더 건조 기술과 비교할 때 콘디벨트 건조방식은 건조속도를 약 5-15배 향상시킬 수 있 으며, 건조 에너지 절감에 큰 효과가 있을 뿐만 아니라 기존의 실린더 건조시 종이가 폭방 향으로 수축되 어 인장 stiffness와 압축 강도 동의 종이 물성 이 저 하되 는 반면 습윤상태 의 섬유를 120도씨이상에서 가열에 의해 리그닌을 연화시킴과 동시에 섬유의 유연성을 증가시켜 준다. 그리고 높은 압력을 가해줌으로써 섬유간의 결합 면적을 증가시키고 건조시 종이의 폭방향의 수축을 감소시켜 인장강도, 내부결합강도, 밀도, 표면평활성, 투기저항성 등 종이의 물성을 대폭 향상시켜주는 혁신적인 제지기술로 인정받고 있으며 국내의 경우 현재 1998년 부터 상업생산을 이루어짐으로써 그 공헌도는 매우 크다고 할 수 있다. 골판지의 주원료가 되는 국산 골판지 고지 (Korean old corrugated container, K KOCC)의 거듭된 재생처리로 인하여 미세분의 함량이 전체 지료의 절반 이상에 달할 뿐만 아니라, 섬유가 각질화와 단섬유화로 인하여 고온압착 건조처리 만으로는 골판지 고지로 생 산된 원지의 강도를 버진펄프로 생산된 원지가 가지는 강도에 준하는 강도로 향상시키는데 한계점을 가지게 된다. 유럽의 제지선진국들은 골판지 원지의 강도를 향상시키는 방편으로 표변에 전분 사이즈 프레스 처리를 도입하였으며 본 연구에서는 고온 압착 건조 처리 설비를 활용한 전분 표면처리의 가능성을 검토하고 골판지 원지의 강도를 향상시키기 위한 표면처리조건을 탐색하였다.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.56-56
• /
• 2009

AISI 316L 스테인리스강에 새롭게 디자인한 서로 다른 3가지 응고모드를 가진 와이어로 FCAW(Flux Cored Arc Welding)을 하였다. 각각의 3가지 와이어는 Pseudobinary phase diagram에 따라 AF, FA, F모드를 가졌다. 미세조직은 $Cr_{eq}/Ni_{eq}$이 증가할수록 델타 페라이트 함량이 증가하였으며, 초정 상의 경우 초정 오스테나이트에서 초정 페라이트로 변태하였고, 연성저하균열의 민감도가 감소하였다. 연성저하균열은 이동결정립계의 형상에 따라 좌우되며, 미량의 페라이트를 함유한 오스테나이트에서는 페라이트가 핀(Pin) 역할을 제대로 하지 못하여 직선형태의 이동 결정립계 따라 입계 미끄러짐의 메커니즘을 통해 전파되었으며, 곡선형태의 이동 결정립계에서는 델타 페라이트가 핀 역할을 하여 역할을 하여 구속 상태에서 응력집중을 막고 응력을 분산시켜 균열이 전파되는 것을 방해하여 균열이 발생되지 않았다.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.331-337
• /
• 2006

Cavity-type beam position monitors were developed in collaboration with KEK to use for the future accelerators such as international linear collider (ILC) or x-ray free electron laser (XFEL) in PAL. BPM components such as BPM cavity, beam tubes, waveguides and feedthroughs were assembled by brazing at the same time to reduce mechanical errors during the fabrication. There are four screwed pins around outer rim of the cavity for the tuning of cavity frequency and x-y isolation. The resonance frequency of BPM is 6.422 GHz, the inner diameter of cavity is 53.822 mm, and the range of mechanical adjusting is $+ / - 250{\mu}m$. The x-y isolation was measured better than -40 dB after tuned. Test results of signal forms, x-y isolations, sensitivities are satisfied within requirements for the KEK ATF2 beam line.

• Composites Research
• /
• v.35 no.2
• /
• pp.98-105
• /
• 2022

In this study, polyvinyl alcohol (PVA)/graphene oxide (GO)/iron oxide (Fe₃O₄) magnetic microgels were prepared using a microfluidic approach and the dye adsorption capacity of the microgels was confirmed. The adsorption capacity (q_e) of the gels was evaluated by varying the dye concentration, pH, and contact time with the microgels. The dyes used in this work were methylene blue (MB), crystal violet (CV), and malachite green (MG), and microgels showed the highest adsorption capacity (191.1 mg/g) in methylene blue. The microgels exhibited the highest adsorption capacity in the dye aqueous solution at pH 10 due to the presence of atomic nitrogen ions (N⁺) on the dye molecules. The adsorption isotherm studies revealed that the Langmuir isotherm is the best fit isotherm model for the dye adsorption on the microgels, indicative of monolayer adsorption. The kinetic analysis exhibited that the pseudo-second order model fits better than the pseudo-first order model, confirming that the adsorption process is chemisorption. In addition, the magnetic microgels showed good reusability and recovery efficiency. It was confirmed that the adsorption capacity of the gels maintains more than 70% of the initial capacity after 5 times of cycle experiments.

• Journal of the Korean Arthroscopy Society
• /
• v.13 no.2
• /
• pp.183-187
• /
• 2009

Purpose: We describe a new and simple technique for arthroscopic fixation of tibial intercondylar eminence avulsion fracture using bioabsorbable pins in skeletally immature patients. Operative Technique: Diagnostic knee arthroscopy is performed using anterolateral and anteromedial portals. Fracture debris and blood clot are debrided to expose the injured site well. The fragment is reduced with the probe and fixed temporarily with a 1.1-mm diameter K-wire that is inserted percutaneously from the anterosuperior aspect of the knee joint. The drill guide is introduced into the joint and the fragment is secured by bioabsorbable, poly-p-dioxanone 1.3-mm pins inserted from different angles. The pins are 40 mm in length. The knee is placed in a long leg cast in extension for 4 weeks to assure that full extension is obtained. Conclusion: Arthroscopic fixation of an tibial intercondylar eminence avulsion fracture using bioabsorbable pins is not a technically demanding, suitable method that ensures fracture healing and restores the stability of the joint.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1210-1215
• /
• 2010

The probe card are test modules which are to classify the good semiconductor chips and thin film before the packaging process. In the rapid growth a technology of semiconductor, the number of pads per unit area is increasing and pad arrays are becoming irregular. Therefore, the technology of probe card needs narrow width and lots of probe tip. In this paper, the probe tip based on the MEMS(Micro Electro Mechanical System)technology was developed a new MEMS probe tip for vertical probe card applications. For the structural designs of probe tip were performed to mechanical characteristics and structural analysis using FEM(Finite Element Method). Also, the contact force of MEMS probe tip compared with FEM results and experimental results. Finally, the MEMS probe card was developed a fine pitch smaller than $50{\mu}m$.