• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.511-512
• /
• 2010

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1917-1919
• /
• 2003

본 연구에서는 바이오 및 환경 분야에 적용 가능한 미세 유체소자 제작에 있어서 4" 유리 / 유리 웨이퍼접합을 시도하였으며, 접합결과 90%이상의 접합면적을 보였다. 접합된 샘플을 산 및 알카리 조건에 따른 인장시험결과 모든 조건에서 약 $2kgf/mm^2$ 이상의 접합강도를 보였으며 파괴는 접합면이 아닌 모재에서 발생되었다. 또한 미세유체소자 제작에 있어서 초음파를 이용하여 유리를 가공하였으며, 폭 $300{\mu}m$, 깊이 $200{\mu}m$의 미세채널을 제작하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.9 s.186
• /
• pp.164-173
• /
• 2006

The cooling capacity of a micro-heat pipe is mainly governed by the magnitude of capillary pressure induced in the wick structure. For microchannel wicks, a higher capillary pressure is achievable for narrower and deeper channels. In this study, a metallic micro-heat pipe adopting high-aspect-ratio microchannel wicks is fabricated. Micromachining of high-aspect-ratio microchannels is done using the laser-induced wet etching technique in which a focused laser beam irradiates the workpiece placed in a liquid etchant along a desired channel pattern. Because of the direct writing characteristic of the laser-induced wet etching method, no mask is necessary and the fabrication procedure is relatively simple. Deep microchannels of an aspect ratio close to 10 can be readily fabricated with little heat damage of the workpiece. The laser-induced wet etching process for the fabrication of high-aspect-ratio microchannels in 0.5mm thick stainless steel foil is presented in detail. The shape and size variations of microchannels with respect to the process variables, such as laser power, scanning speed, number of scans, and etchant concentration are closely examined. Also, the fabrication of a flat micro-heat pipe based on the high-aspect-ratio microchannels is demonstrated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1175-1178
• /
• 2005

Brittle materials, especially single-crystal silicon wafer, are widely used for sensors, IC industry, and MEMS applications. e general machining process of crack easy materials is by chemical agents, but it is hazardous and time consuming. Also, it is difficult to get high aspect ratio micro structure. As an alternative tool, an AJM(Abrasive jet machining) is promising method in terms of high aspect ratio and production cost. In this study, to get more precise detail compared to general AJM, photo polymer mask, SU-8, used in photolithography was applied in AJM. Process parameters such as abrasive diameter, air pressure, nozzle diameter, flow rate of abrasive in AJM and a variety of conditions in spin coating were decided. Finally, micro channel and mixer was fabricated to see the efficiency of the AJM with photo polymer mask.

• Laser Solutions
• /
• v.18 no.2
• /
• pp.11-13
• /
• 2015

Pressure-drop in a micro-channel is critical when a hole diameter is less then 100um with the high aspect ratio, more than 40. To minimize these pressure loss for micro-channel applications is important and there would be the best hole diameter, taper angle, and their combinations. In this work, the parametric study for laser drilling of anodized material is conducted to obtain the micro-channel hole with high aspect ratio.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.685-686
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.637-638
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.401-402
• /
• 2009

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.413-414
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.197-198
• /
• 2011