• Journal of ILASS-Korea
• /
• v.24 no.3
• /
• pp.105-113
• /
• 2019

In this paper, a study of Urea-SCR System for Dosing Injector for responding to enhanced environmental regulations has been conducted. There is a limit to the experimental approach due to the structural characteristics of the injector. In order to overcome this problem, The analysis was performed assuming unsteady turbulent flow through computational fluid analysis and the internal flow characteristics of the injector were analyzed. By changing the nozzle shape of the injector, the performance factors of the swirl injector by shape were selected and compared. The design parameters were modified by changing the diameter of the nozzle at a constant ratio compared to the base model. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. The Conv. model to which the taper was applied showed the dominance in mass flow rate, discharge coefficient and swirl because of the smooth fluid flow by shape. Swirl coefficient, outlet mass flow, and sac volume were selected as performance parameters of the injector. As a result of the comparison coefficient derivation with those performance parameters for comparing the performance of the model-specific injector, the Conv-140 model with the nozzle diameter expanded by 140% showed the best value of the comparison coefficient.

• Journal of ILASS-Korea
• /
• v.26 no.4
• /
• pp.189-196
• /
• 2021

Spray drift of agricultural nozzles has become a big issue because it causes low precision targeting and environmental pollution. In order to reduce the spray drift, study spray characteristics of agricultural nozzles is virtually important. In this study, shadowgraph and Mie-scattering visualization techniques were used to study the macroscopic spray and atomization characteristics of an agricultural nozzle. PDPA was used to measure the atomization characteristics of spray. The injection pressure is set to 1 bar, 3 bar and 5 bar, which covers the working range of the nozzle. For the PDPA experiment, 75 points were measured in an area of 160 mm × 120 mm at 10 mm intervals directly below the nozzle to grasp the overall atomization characteristics of the spray. It was found that the spray width and sheet width showed a linear correlation. As the injection pressure increased, the sheet expansion in the 0-degree direction and the sheet swing in the 90-degree direction jointly promoted the breakup of the sheet. In addition, the area close to the central axis had a large droplet velocity, and since a large droplet velocity promoted atomization of spray, the area close to the central axis had a smaller spray droplet diameter than the left and right regions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.495-501
• /
• 2012

Spray characteristics of liquid jets in crossflow, which can be observed in the liquid jet injection system of a gas turbine or ramjet engine, were experimentally investigated. By measuring liquid jet penetration in the case of single orifice and double orifice injectors, the experimental formula for jet penetration was modified to consider penetration distances greater than that considered in a previous study. The changes in spray characteristics resulting from changes in the liquid jet and crossflow pressure, including SMD and jet disintegration, were carefully studied. Specifically, the jet penetration was measured for different injector shapes, and in the case of a double orifice injector, the penetration of the rear orifice jet was found to be greater by approximately 20% ($L_h$ = 4 mm) compared to that in the case of a single orifice injector because of the influence of the front orifice.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.354-358
• /
• 2007

An experimental study was performed to understand spray characteristics of the slinger injector. system for the micro turbojet engine. In this fuel injection system, fuel is sprayed and atomized in the combustor by centrifugal forces of engine shaft. This experimental apparatus consist of a high speed rotating Spindle, slinger injector, pressure tank and acrylic case. The droplet size and velocity were measured by PDPA(Phase Doppler Particle Analyzer) and spray was visualized by using Nd-Yag laser-based flash photography. From the test results, the droplet size(SMD) is largely affected to rotational speed, mass flow rate and the number of injection orifice. From the this experimental study, we could understand the spray characteristics of the slinger injection system and obtain the optimum shape of the slinger injector nozzle which is suitable for the micro turbojet engine.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.59-70
• /
• 2021

An experimental study was conducted to observe the spray characteristics for different flow rates and rotating speeds of a rotating fuel nozzle of a slinger combustor. The water spray ejected from the nozzle orifice was visualized using a high-speed camera and a light source. It was confirmed that the atomization was improved, as the flow rate decreased and rotating speed increased. The characteristic maps for the spray characteristics and performance parameters showed that the aerodynamic Weber number and the liquid-air momentum flux ratio were associated with the liquid primary breakup, and the liquid-air momentum flux ratio and Rossby number were closely correlated with the liquid ejection mode.

• Journal of Energy Engineering
• /
• v.4 no.3
• /
• pp.394-401
• /
• 1995

본 연구는 중심부에 액체, 외주부에 산화제가 흐르는 기액 동축분류의 유동장에 대한 것이다. 기액 동축 분사기는 연료의 분사량이 적은 소형 연소시스템을 고려하여, 실험은 연공비(W1/Wa)가 0.6 이하를 대상으로, 물과 공기를 사용하여 분사조건에 따른 분무특성과 기액 2상 분무류의 기본구조를 조사하여 액적의 확산, 기액혼합특성에 대하여 검토하여 다음과 같은 결론을 얻었다. 반경방향 기상속도분포 및 액적유속분포는 분구직경 및 분사조건에 관계없이 정규분포에 가까운 형태를 취하고 있으며, 각각 식 (2) 및 (3)으로 나타낼 수 있다. 기상속도는 반치폭은 축방향에 따라 일정한 구배 (≒4.6)로서 증가하며, 기상만의 단상분류의 구배(≒6)에 비해서 완만하다. 액적유속 반치폭은 축방향에 따라 더욱 완만한 구배(≒3.1)로서 증가한다. 무차원 액적유속분포는 축방향에 따라 일정한 구배(n≒1.5)로서 감소한다. 액적의 확산은 상대적으로 기액유량비가 클수록 효과적으라고는 말할 수 없고, 최대 확산을 이루는 최적의 기액유량비가 존재한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.2
• /
• pp.121-127
• /
• 2011

NOx (Nitrogen Oxide) reduction system periodically needs a rich or stoichiometric operating condition to reduce NOx. A new method that optimizes the control of external HC injection into a diesel exhaust pipe for HC-type LNT (Lean NOx Trap) catalyst system has been developed. In this paper, these catalysts are called HC-LNT catalysts. The concentration and amount of HC can be controlled by controlling the external injection. In this study, we investigated the relationship between the spray behavior of hydrocarbons injected into the transparent exhaust pipe and NOx reduction characteristics. From the results of this experiment, we obtained useful information about the optimum injection and position of HC injector to the exhaust pipe. Further, we obtained useful information about the optimal injection condition for an HC-LNT catalyst system with a gasoline PFI (port fuel injection) typeinjector.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.945-951
• /
• 2012

A water emulsion fuel can be used to reduce soot and NOx emissions simultaneously because it has a lower combustion temperature and better fuel atomization owing to the evaporative latent heat and microexplosion of water. Moreover, it can be used without making special modifications to conventional diesel engines. Therefore, this fuel has attracted considerable research attention. In addition, lower-grade fuels are being considered for use in conventional engines because of an increase in oil prices. In this study, we investigated the combustion and exhaust characteristics of MDO (marine diesel oil), which has a lower grade than common diesel oil, and ME (MDO water emulsion) under various test conditions in an automotive diesel engine.

• Resources Recycling
• /
• v.24 no.6
• /
• pp.38-44
• /
• 2015

It studies that effect of limestone of physicochemical characteristic on the performance of flue gas desulfurization (FGD) and application examination for technology of wet type FGD process and to utilize the limestone in Donghae-Samcheok. The experiment method was measured total neutralizing capability (TNC) using the lab scale experimental apparatus based on the HCl titration test. The results of TNC of limestone samples were more dependent on the physical characteristics including particle size rather than chemical compositions such as CaO content and particle size of limestone get smaller, TNC is increased.