• Tribology and Lubricants
• /
• v.27 no.6
• /
• pp.308-313
• /
• 2011

In this study, friction tests were performed in order to investigate the effect of sliding velocity and normal load on the friction characteristics of DLC (a-C:H) and WC/C (a-C:H:W) using a ball-on-disk type friction tester. DLC and WC/C were deposited on AISI 52100 steel balls. Friction tests against carburized SCM 415 Cr-Mo steel disks were carried out under various sliding velocity (0.1, 0.78, 1.56, 3.13, 6.25, 12.5, 25, 50 and 100 mm/s) and normal load (2.4, 4.8 and 9.6 N) conditions while the relative humidity was 20~40 % R.H. and air temperature was $16{\sim}24^{\circ}C$. As results, kinetic friction coefficients of DLC and WC/C were obtained under each test condition. The results show that the kinetic friction coefficients of DLC and WC/C generally increase with the increase in sliding velocity. And, under the same sliding velocity condition, the kinetic friction coefficients are almost constant regardless of normal load. In addition, the kinetic friction coefficients of DLC are lower than those of WC/C under the same test conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.2055-2061
• /
• 2009

There can be some variation in the load carrying capacity of high-tension bolt friction joints when oversize bolt holes are made on the base plate and the cover plate. This study performed a static tensile test in order to examine the variation of slip load and slip coefficient according to standard bolt hole and oversize bolt hole in high-tension bolt friction joints. According to the results of the static tensile test, the slip coefficient changed to some degree according to oversize bolt holes on the base plate and the cover plate, but it was somewhat unreasonable to find a pattern in the change. Sliding strength showed a difference of up to 26% between the use of standard bolt holes and the use of oversize bolt holes. Because this exceeds the design sliding strength, however, its effect on the serviceability of joints under service load is insignificant. Thus, if the regulation on oversize bolt holes, which may be inevitable in making steel members, is applied flexibly, we may improve efficiency and economy in the design and construction of structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.439-445
• /
• 2005

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as seal rings, pump parts, meter parts, and so on. In this study, the effects of each other purity on the mechanical and tribological properties of alumina and zirconia ceramics were investigated. Sliding distance, sliding speed, contact load. friction coefficient, the amount of worn out material at a certain time, and the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. We obtained the good properties of friction coefficient and wear resistance at the purity 99.7$\%$ of alumina. However, The purity 95$\%$ were great at the wear amount of worn out material.

• Tribology and Lubricants
• /
• v.1 no.1
• /
• pp.30-37
• /
• 1985

동수압적 미끄럼베어링의 작동원리는, 두개의 서로 경사진 면이 윤활제를 그 사이에 두고 상대적인 운동을 함에 있어서 두면사이에는 윤활유 막이 형성되어 압력이 형성되고 두면에 작용하는 하중의 지지하게 되므로 직접적 마찰없이 상대적 미끄럼운동을 한다는 것이다. 동수압적 유체윤활은 윤활틈새 내의 윤활유동에 동수압적 점성유체역학 이론을 적용하며 베어링윤활유막의 압력분포를 계산하기 위한 편미분 방정식의 발견이 그 근본을 이루고 있고, 미끄럼베어링에 대한 기본적연구는 1900년 이래로 계속 수행되고 있다. 크랭크샤프트와 피스톤 연결봉 사이의 베어링은 동하중을 크게 받으며 회전하므로 저어널과 축의 상대운동은 회전운동과 윤활면의 수직운동으로 나누어 해석할 수 있다.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.167-175
• /
• 2000

An experimental research to evaluate the slip coefficient of high-strength slip-critical-type bolt connection of weathering steel plate has been performed in this paper. Experiments were performed with several surface conditions such as clean mill scale with hand or power brush cleaning, shot blast cleaned, inorganic zinc primer coated, and weather coated surfaces. Also, the relaxation of bolt clamping force was estimated during 500 hours. It was ascertained from the experiments that slip coefficients are greater than 0.40 in all faying surface conditions except mill scale surface with power brushing. The quantify of relaxation depended on the surface conditions and was $3{\sim}8%$, i.e., less than 10%.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.177-185
• /
• 2000

An experimental research to evaluate the slip coefficients of high-strength friction-type bolt connection of weathering steel plate has been performed in this paper. The test specimens with mill scale or shot blast had been exposed in open air during 3 and 6 months and cleaning of rust surface by hand brushing, power tool brushing and no cleaning was considered. The relaxation of bolt clamping force had also been measured during 600 hours. It was found that slip coefficients increased to the value over 0.6 with exposure except mill scale surface by power tool brushing. The relaxation of bolt tension force in exposed specimens also increased and maximum value reached to about 10%.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.26-32
• /
• 1996

오랜 역사에 걸쳐 연구자들은, 마찰력은 주로 접착에 의한 것으로 믿어 왔으며, 이러한 주장은 실험적으로 증명되지 못했다. 한편, 미끄럼 두 표면 사이의 건식 마찰력은 두 표면 사이의 기계적인 상호작용에 의한 것으로 알려져 있다. 이 연구에서는 두 표면 사이의 기계적 상호작용을 제거함으로써 마찰계수를 감소시키는 방법을 제시하였다. 매끄러운 경한 표면에 얇은 elastomer층을 입힌 비윤활 최소 마찰계수에 대한 본 실험결과는 앞으로 정밀기계부품의 충격을 받는 부위에 응용할 수 있을 것으로 기대된다.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.121-129
• /
• 2001

The friction characteristics of natural rubber plates under various conditions including sliding speed, normal force, hardness, lubrication conditions and thickness of plate are analyzed experimentally. The frictional force and normal force are measured by a tester pin and a load ceil with strain gages. Experimental results suggest that the coefficient of friction decreases with increasing the hardness of rubber and decreasing the thickness of plate. The effect of sliding speed is not significant over the speed range employed. The coefficient of friction is found to be about 0.1 under oil lubrication condition and varies from 0.9 to 3.9 under no lubrication condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.159-163
• /
• 2001

마찰구동은 다른 구동방식에 비하여 구조가 간단하고, 기계적인 정도를 얻기 쉬우며, 백래쉬 등에 기인하는 비선형 요소인 로스트모션이 없고 관성이 작아 구동력이 작은 이점이 있다. 그 반면에 접촉부에서 미끄럼이 발생하여 큰 구동력을 얻기 어렵고 마찰저항에 의하여 마멸이 생기는 결점이 지적되고 있다. 본 연구에서는 초정밀가공기용 위치결정기구로 마찰구동기구를 사용하기 위하여 위치 결정도에 관한 설계, 구동력의 설계 및 재료의 선택에 관하 여 분석하고 시작품을 제작하여 특성을 연구하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.261-262
• /
• 2013