• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1756-1762
• /
• 1991

본 연구에서는 막냉각되는 터빈블레이드에서의 열전달 계수를 측정하기 위하 여 열전달과 물질전달의 상사관계를 이용하였다.터빈블레이드의 선단을 다른 연구 에서와 마찬가지로 원봉으로 모사하였고, 원봉의 표면에 위치하고 있는 1열의 분사홀 로부터 제트가 분사될 때 분사홀 근처 및 그 하류에서의 물질 전달계수를 측정하기 위 해 나프탈렌승화법을 이용하였다. 분사홀 열의 위치를 정체점에서 하류방향으로 이 동시키면서, 물질전달계수의 변화를 연구하였고, 분사율(M=.rho.$_{j}$ U$_{j}$ /.rho.$_{\infty}$ U$_{\infty}$)의 영향도 고찰하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.6
• /
• pp.415-421
• /
• 2017

As stricter environmental regulation have led to an increase in the water treatment cost, it is necessary to quantitatively study the input power of the aeration process to improve the energy efficiency of the water treatment processes. The objective of this study is to propose the empirical correlations for the mass transfer coefficient with the gas hold-up and input power in order to investigate the mass transfer characteristics of the aeration process. It was found that as the input power increases, the mass transfer coefficient increases because of the decrease of gas hold-up and increase of Reynolds number, the penetration length, and dispersion of mixed flow. The correlations for the volumetric mass transfer coefficients with gas hold-up and input power were consistent with the experimental data, with the maximum deviation less than approximately ${\pm}10.0%$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.264-270
• /
• 2008

Most of burning rate models used in hybrid combustion depend solely on oxidizer flux. But this empirical relation can not represent well the important effect of the thermo-chemical properties of solid fuel and thereby requires different value of empirical exponent and constant for each fuel considered. In this study, a new burning rate correlation was proposed using the mass transfer number(B number) which encompasses the thermochemistry effect of solid fuel and the aerodynamic effect caused by the combustion on the solid fuel surface where the effect of aerodynamic property in the mass transfer number was studied. The PMMA, PP, and PE were chosen as fuel, and gas oxygen as oxidizer. The new empirical burning rate expression depending on both the oxidizer flux and the mass transfer number was able to predict the burning rate of each fuel with just a single exponent value and constant, and it was found that the aerodynamic effect on the blowing effect did show a minor effect on the burning rate correlation.

• Nuclear Engineering and Technology
• /
• v.20 no.2
• /
• pp.120-131
• /
• 1988

A souce term model describes mathematically the source of radionuclides as they begin slow migration and decay in deep groundwater. Various source term models based on mass-transfer analysis and measurement-based source term models are reviewed. Ganerally, two processes are involved in leaching or dissolution: (1) chemical reactions and (2) mass transfer by diffusion. The chemical reaction controls the dissolution rates only during the early stage of exposure to groundwater. The exterior-field mass transfer may control the long term dissolution rates from the waste solid in a geologic repository. Mass-transfer analyses re3y on detailed and careful application of the governing equations that describe the mechanistic processes of transport of material between and within phases. If used correctly, source term models based on mass-transfer theory are valuable and necessary tools for developing reliable predictions.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.6B
• /
• pp.689-694
• /
• 2006

The system performance of a bioactive foam reactor (BFR), that consists of a foam column using a surfactant and a biodegradation basin containing suspended bacteria, was investigated for the treatment of gaseous toluene or a mixture of four volatile organic compounds (VOCs, benzene, toluene, p-xylene, and styrene). Overall, the BFR achieved stable VOC removal efficiencies, indicating that it can be used as a potential alternative over conventional packed-bed biofilters. Furthermore, a dynamic loading test showed that relatively constant removal was maintained at the elevated loading due to a high mass transfer rate in the foam column. However, as the inlet concentration of VOCs increased, a portion of the VOCs mass-transferred to the liquid phase was stripped out from the biodegradation basin, resulting in a decrease in the overall removal efficiency. In the BFR, the removal efficiency of the individual VOC was mainly determined depending on the biodegradation rate (styrene > toluene > benzene > p-xylene), rather than the mass transfer rate. Consequently, increases in the microbial activity and the volume of the basin could improve the overall performance of the BFR system. Further investigation on microbial activity and community dynamics is required for the BFR when subjected to high loadings of VOC mixtures.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.10
• /
• pp.817-824
• /
• 2015

Experiments were carried out to investigate the flow and mass transfer characteristics of an orifice nozzle. Measurements of primary and suction flow rates, dissolved oxygen concentration, and electric power were obtained. Vertically injected mixed-jet images were captured by a direct visualization technique with a high speed camera unit. The mass ratio, volumetric mass transfer coefficient, and mass transfer performance were calculated using the measured data. As the primary flow pressure increases, the mass ratio decreases slightly, while the volumetric mass transfer coefficient and electric power increase. As the primary flow pressure increases and the mass ratio decreases, the mass transfer rate increases because of the fine bubbles and wider distribution of the bubbles.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.56-63
• /
• 1998

The present study investigated local heat transfer characteristics around a film cooling hole with variations of free stream turbulence intensity The film cooling jet is injected through a single hole inclined at $30^{\cire}$ to the surface and laterally at $45^{\cire}$ for the blowing rates of 0.5, 1.0 and 2.0. Turbulence generating grids are used at upstream of the film cooling hole to change the turbulence intensity of free stream. Free stream turbulence intensity without grids is 0.5%. Two different turbulence generating grid is installed at different at locations upstream of the film cooling hole so that turbulence intensity of free stream varies from 3% to 10%. The naphthalene sublimation technique has been employed to determine local heat/ mass transfer coefficients. With low free stream turbulence intensity, heat/mass transfer augmented area by coolant or free stream is distinguished evidently. However, when free stream turbulence intensity is high, heat transfer is enhanced in all region and heat transfer enhanced regions are not clearly divided due to vigorous mixing of coolant and free stream. The peak values of heat/mass coefficients are decreased and the distributions of heat/mass transfer coefficients are more uniform with high turbulence intensity. The effect of turbulence intensity on heat transfer characteristics is more evident as blowing rate is higher.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.685-693
• /
• 1990

The heat transfer coefficients were calculated numerically to see the effects of radiation around the porous medium put on the flat plate at a distance from the leading edge of flat plate for the two-dimensional laminar flows. To verify the analytical model developed and invoke the heat/mass transfer analogy, an experiment was carried out using naphthalene sublimation technique. From the effects of the wake, Sherwood number is maximum around the region where the porous medium is attached. The theoretical results correspond well with the experimental results at small Darcy number. Permeability of ceramic blocks used for experiment was also measured and the Forchheimer equation is applicable in our measurement range.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.7
• /
• pp.770-775
• /
• 2006

Biofilters packed with various materials commonly show problems such as low performance and clogging in a long-term operation. Recently, a bioactive foam reactor(BFR) using surfactants has been suggested to ensure efficient and stable VOCs removal performance. This study was mainly conducted to investigate the feasibility of the BFR system using styrene as a model compound. An abiotic md a biotic tests were conducted to estimate a mass transfer coefficient($K_La$) and a specific substrate utilization coefficient(k) for the BFR, showing the rate of mass transfer was greater in the BFR than in other diffuser systems. A dynamic loading test also indicated that the performance of the BFR was stable under a shock loading condition. Furthermore, the maximum elimination capacity of the BFR was determined to be 109 $g/m^3/hr$ for styrene, which was much higher than those for biofilter systems generally reported in the literature. Overall, the experimental results suggest that the BFR be a potential alternative to the conventional packed-bed biofilters.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.323-326
• /
• 2005

In this study, experimental studies were performed the combustion characteristics of end- burning hybrid propulsion system. PMMA, PE were used as fuel and gas oxygen as oxidizer. The regression rate depend on oxidizer flow rate also on thermodynamic properties of fuel. as result, empirical formula for regression rate was deduces with oxidizer flow rate and mass transfer coefficient B number.