• Culinary science and hospitality research
• /
• v.15 no.3
• /
• pp.128-138
• /
• 2009

This study analyzed the qualitative characteristics and antioxidant effect of Artemisia by experimenting its medicinal effect and functionality. Moisture content increased in proportion to heating time and decreased in reverse proportion to temperature and time. In the contents of mineral compounds, P was shown in the order of roasting temperature $230^{\circ}C$ > $80^{\circ}C$ > $110^{\circ}C$, and blanching condition was 0.50% in one and two minute treatment and 0.38% in five minute treatment. The contents of Ca didn't have significant differences according to the types of treatment. The contents of Fe were higher than general vegetables with 0.54~1.02 mg/100 g. The contents of phenolic compounds were highest in the control plot, followed by one minute blanching and roasting at $110^{\circ}C$ was the lowest. The intensity of electron donating ability was decreased in 14 minute blanching at $230^{\circ}C$. Based on the result of the study, roasting at low temperature and blanching which is Korean traditional method are desirable when cooking with Artemisia.

• Journal of the Korea Concrete Institute
• /
• v.19 no.4
• /
• pp.475-482
• /
• 2007

The property and applicability of the organic-inorganic synthesized penetrating and reinforcing agent, which is developed in order to improve durability of concrete structures and prevent deterioration that may occur as service years increased, are researched with experimental works. TEOS (tetra-ethoxyorthosilicate) and acrylate monomer are synthesized by the solution polycondensation method in order to formulate silicate with sol-gel process and improve durability of concrete. Additional substances such as isobutyl-orthosilicate is supplemented in order to improve the performance of the agent. After the developed organic-inorganic penetrating reinforcing agent penetrates, a flexible impact alleviating layer is formed with organic monomers as well as the agent strengthens concrete by filling up the internal pore of concrete with stable compounds after penetration. Penetrating and reinforcing agent can be applied as an effective life management method because it makes concrete more durable against the aging factors, such as chloride ion, carbonation, freezing-thawing, and compound aging.

• Clean Technology
• /
• v.12 no.3
• /
• pp.175-181
• /
• 2006

The feasibility of the use of porous fossil diatoms for indoor air pollution control was investigated via the characterization of physical and chemical properties. The fossil diatoms were observed by SEM(Scanning Electron Microscope). Diatomite had well-distributed pores below 5 nm and relatively large surface area compare to sericite. However, no porosity in sericite was found. Results showed that diatomite had better performance than sericite in respect to porosity and large surface area. But diatomite which is thermally treated at $950^{\circ}C$ has no porosity and low surface area because of combustion of fossil diatoms or calcination of inorganic oxide at high temperature, and has poor adsorption capability of ammonia gas. In conclusion, porous diatomite has relatively high performance to adsorb noxious chemical compounds, such as ammonia gas and VOCs.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.14 no.4
• /
• pp.151-160
• /
• 2006

Anaerobic treatment of landfill leachate was studied to investigate the behaviors of pollutant and the characteristics of microorganism for 10 months. The upflow anaerobic sludge blanket (UASB) reactor achieved about 90% chemical oxygen demand (COD) removal at organic loading rates(OLR) up to $20kgCOD/m^3.d$. At higher OLR ($8-20kgCOD/m^3.d$), the propionate concentration increased, indicating that converting propionate to acetate was the rate-limiting step. Nevertheless, increase in the precipitate inside and on the surface of granules as well as on the wall of the reactor resulted in operational problems. The main inorganic precipitate in the granule was calcium compound. Although specific methanogenic activity (SMA) was not affected seriously in this study, metals had to be removed prior to anaerobic treatment so as to be free from the excessive inorganic accumulation that resulted in operational problems.

• Journal of Navigation and Port Research
• /
• v.38 no.6
• /
• pp.601-606
• /
• 2014

Lab scale experiment study was carried out for biological treatment process development in shipboard. SBR(Sequence Batch Reactor) process with BM(Beneficial Microorganisms) was investigated for practical application on shipboard sewage treatment. From the results it was suggested that SBR process with BM might be a suitable process in terms of harmful materials removal. By adding BM to SBR system, the useful species of microorganisms and EPS(Extracellar Polymetric Substances) in sludge was increased. It was found that the biodegrability and harmful organic compounds like VOCs and harmful inorganic compounds like heavy metals. was reduced over 70%. As far as reclamation water is considered, this process is very advantageous to special environments such as cruise ships, because the method of adding BM makes it unnecessary to add other facilities on the SBR system.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.71-74
• /
• 2006

High $J_c$ over 1 $MA/cm^2$ YBCO film has been successfully prepared using nitrate precursors by spray pyrolysis method. Aerosol drolpets generated using a concentric spray nozzle were directly sprayed on a $LaAlO_3$(100) single crystal substrate. The cation ratio of precursor solution was Y:Ba:Cu=1:2.65:1.35. The distance between nozzle and substrate was 15 cm. Deposition temperature was ranging from $750^{\circ}C\;to\;800^{\circ}C$. Deposition pressure was 100 Torr, and oxygen partial pressure was varied from 10 Torr to 50 Torr. The microstructure, phase formation, texture development and superconducting properties of deposited films were largely changed with oxygen partial pressure. Deposited films showed a texture with(001) planes parallel to substrate plane. High quality film was obtained when film was deposited at $760^{\circ}C$ with an oxygen partial pressure of 30 Torr. The critical current density($J_c$) of the YBCO film was 1.75 $MA/cm^2$ at 77 K and self-field.

• Applied Chemistry for Engineering
• /
• v.21 no.5
• /
• pp.581-585
• /
• 2010

The surface of Alnico, one of the industrial dust waste, was treated with 1,3,5-trivinyl-1,3,5-trimethylcyclotrisilazane (VMS) as a surface treating agent and used as the filler for vibration isolator rubber. Maleated EPDM prepared from bulk polymerization of EPDM with maleic anhydride was copolymerized with ${\alpha},{\omega}$-bis(3-aminopropyl)polydimethylsiloxane to obtain maleated EPDM-polydimethylsiloxane copolymer (MEPDM-PDMS). EPDM/Alnico/MEPDM-PDMS vibration isolator rubber was prepared from compounding with Alnico treated with surface treating agent, 25 and 50 phrs to EPDM, respectvely based on 1 to 10 wt% of MEPDM-PDMS to EPDM. From the measurement of the thermal properties to the rubber, the glass transition temperatures (Tg) for the rubber containing maleated EPDM-PDMS copolymer was slightly lower temperature, $33^{\circ}C$ than EPDM rubber, and also DMA results showed higher tan ${\delta}$ peak to the rubber prepared from compounding with EPDM-PDMS copolymer. From the results, rubber prepared using EPDM-PDMS copolymer had better vibration isolator property.

• Membrane Journal
• /
• v.23 no.1
• /
• pp.80-91
• /
• 2013

Metal-templated condensation of cyclohexanedione dioxime and phenylboronic acid in the presence of Fe(II) sulfate heptahydrate proceeds cleanly in methanol to furnish the Fe(II) clathrochelate. An organic/inorganic hybrid membranes composed of Fe(II) clathrochelate and polyethersulfone was prepared by using phase inversion method. For membrane preparation, the Fe(II) clathrochelate was highly soluble (3~5 g/L) in DMF, NMP, and DMAc, which meets the requirements for the solubility of metal complexes in polar aprotic solvent used in membrane preparation. It was stable even in the presence of strong acids, such as trifluorosactic acid (pKa = 0.3). It was characterized by UV-vis spectroscopy, and their stability in solution phase studied in the presence of (i) strong acids or (ii) competing chelates. Organic/inorganic hybrid membranes were prepared with polyethersulfone, polyvinylpyrrolidone, p-toluenesulfonic acid, Fe(II) clathrochelate and DMF by using nonsolvent induced phase inversion method. The addition of Fe(II) clathrochelate leads increase of surface pore density, mean pore size and flux. We can obtain highly asymmetric membranes by addition of Fe(II) clathrochelate.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.735-740
• /
• 2002

In order to improve the anti-fogging property of polymer films, organic-inorganic hybrid coating solutions which have good hydrophilic property and transmission in the range of visible light were synthesized by the sol-gel method. The coating solutions were prepared by adding glycidoxypropyl trimethoxysilane(GPS) to a colloidal silica(15 nm) suspension(Ludox). GPS as silane coupling agent forms strong bonds to the colloidal silica and surrounding polymer matrix and links two different materials together. Solutions prepared by addition of GPS at the acidic condition resulted in coatings that were less prone to cracking, while those at the basic condition caused coatings with more cracking. These resulted in better hydrophilic property and transmission in the range of visible light for the solution prepared at the acidic condition(pH 2). Compared with coatings under acidic conditions, coatings prepared at basic conditions showed worse hydrophilic property and transmission in the range of visible light.

• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.335-339
• /
• 2007

In order to overcome the problem of poor hardness of transparent polycarbonate (PC) sheets, organic-inorganic hybrid hard coating solutions, which show a high refractive index above 1.58, were made by the sol-gel method. These hybrid coating solutions were obtained from mixture of titanium tetraisopropoxide (TTIP), and (3-glycidoxypropyl)trimethoxysilane (GPTMS). The PC sheets were spin-coated, and cured at $120^{\circ}C$ for 2 hr. Change of refractive index in the range of 1.53-1.61 was obtained by varying the GPTMS content. The refractive index of the coated film decreased with increasing the GPTMS content, while the pencil hardness of the coated film was found to increase with increasing the GPTMS content.