• Proceedings of the Safety Management and Science Conference
• /
• 2006.04a
• /
• pp.195-200
• /
• 2006

건설업계는 제조업과 특성이 달라 여러 가지 문제점이 엿보인다. 특히, 건설업 근골격계 질환에 대한 연구 및 지원은 별로 찾아볼 수가 없다. 근골격계 질환의 제조업과 건설업의 비율을 보았을 때 "2004 산업재해분석" 요양자 업종별 분포를 보면 제조업이 3,281명(79.79%)로 건설업의 63명(1.53%)보다 월등히 많은 것으로 조사되었다. 이는 미국의 사례를 보았을 때, 2007년 업종별 분포를 보면 건설업이 42,867명(26.20%), 제조업이 101,437명(36.23%)로 우리나라에 비해 건설업 근골격계 질환자가 상대적으로 많은 것으로 조사되었다. 이는 건설업에서의 근골격계 부담 작업 실태조사 등을 통하면 제도적 문제점이나, 근로자가 몰라서 질병에 이환되는 경우가 아닌가 한다. 건설업 근로자들은 건설업 특성상 근골격계 질환예방을 위한 도구를 거의 사용하지 못하고, 작업의 연속성, 지속성이 떨어지므로 부자연스럽고, 불편한 자세를 작업을 위해 수시로 반복하여 취할 수 밖에 없다. 따라서 건설업체에 중대재해를 줄이기 위한 노력 뿐 만 아니라, 열악한 건설업체의 근로자의 근골격계 질환 예방에 대한 제도적인 지원과 안전담당자 교육, 근로자에 대한 근골격계 질환 예방교육(스트레칭, 작업 자세, 동작, 근력강화, 적절한 휴식시간 부여) 등 대책이 절실히 필요하고 하겠다.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.28-33
• /
• 2016

This study was conducted to investigate the effects of deep eutectic solvent (DES) treatment on properties of TMP fibers and handsheets. DES was prepared by mixing of lactic acid and betaine (L and B), and the molar ratio of these two components mixtures was controlled to 2:1 (L:B=2:1) and 5:1 (L:B=5:1). As results, lignin was partly extracted from the TMP fibers. Especially, the delignification of TMP samples was promoted according to the increase of the molar ratio of lactic acid. Except for tear index, both tensile index and burst index of handsheets were increased when higher molar ratio of lactic acid was mixed for DES preparation. However, the LB DES treatment of TMP fibers didn't give any effect on the optical properties of TMP handsheets. The plausibility of TMP fiber was to be enhanced by LB DES treatment.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.75-79
• /
• 2009

The ratio of aniline dimer (p-aminodiphenylamine), which is a nucleation site of chain growth in a chemical polymerization of aniline monomer, to aniline monomer was controlled to synthesize polyaniline with the molecular weight ($M_w$) between 10000 and 20000 g/mol. The result of OCP measurement showed that the reaction rate of polymerization was increased as the mole ratio of dimer was increased. The increase in the molar ratio of dimer resulted in the shift of absorption wavelength of polyaniline to the short wavelength region on measurement of UV/Vis and the decrease of molecular weight on the measurement of GPC.

• New & Renewable Energy
• /
• v.2 no.4 s.8
• /
• pp.46-55
• /
• 2006

본 연구는 불소그룹을 함유한 술폰화된 아릴렌에테르계 블록 공중합체 고분자 전해질막의 제조 및 연료전지 특성에 관한 것이다. 이러한 불소그룹을 함유한 술폰화된 아랄렌에테르계 블록 공중합체를 제조하기 위하여 양말단에 불소계 비닐기를 가지면서, 고분자 전환시 상온에서 술폰화 가능한 biphenyl계 단량체와 술폰화가 불가능한 sulfonyl계 단량체를 각각 합성하였다. Biphenyl계 단량체로 부터 올리고머를 합성한 후 sulfonyl계 단량체와 열적 고리화 부가중합을 하여 다양한 몰조성을 갖는 일련의 perfluorocyclobutane(PFCB)기를 포함하는 블록 공중합체를 제조하였다. 제조된 블록 공중합체를 상온에서 술폰화제인 chlorosulfonic acid(CSA)를 이용하여 후술폰화시켜 강산 이온기인 sulfonic acid를 biphenyl계 올리고머 부분에 선택적으로 도입하였다. 이렇게 제조된 술폰화된 고분자를 제막한 후 연료전지 특성을 Nafion-115와 비교하였다. 술폰화가 되는 올리고머 블록의 비율 증가에 따라 이온교환능력 (IEC)이 증가하였고 , 그에 따른 팽윤도 역시 증가하는 것을 보였다. 술폰화된 고분자들은 건조 및 습윤 상태에서도 기계적 강도가 우수하였다. 최적화된 술폰화 블록 고분자(S-2) 를 대상으로 membrane electrolyte assembly(MEA) 를 제조하여 연료전지 초기성능을 측정한 결과 Nafion-112와 유사한 전기화학적 성능을 나타내었다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.2
• /
• pp.141-145
• /
• 2002

Successive ion Exchange Column model was developed with the combination of mass action law and mole balance equation. consuming that ions entering the ion exchange bed pass the resin layer via consecutive ion exchange equilibrium. The application of the model to condensate polishing demineralizer in nuclear power plants indicates that the leakage of $Na^+$ and $Cl^-$ depends upon the degree of resin regeneration and that the ratio of specific ion concentration in Influent to in effluent is subject to the characteristics of resin and solution. The model can account for the local in-equilibrium with the correction of resin concentration and also can be applicable to a competitive ion exchange.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.410-416
• /
• 2006

For highly efficient operation of a Bunsen process section in an iodine-sulfur thermochemical hydrogen production cycle using nuclear heat, the process characteristics of $H_2SO_4-HI-H_2-O-I_2$ mixture system for separating into two liquid phases ($H_2SO_4$-rich phase and $HI_x$-rich phase) and the distribution of $H_2O$ to each phase were investigated.The experiments for process variables were carried out in the temperature range, from 298 to 353 K, and in the $H_2SO_4/HI/H_2O/I_2$ molar ratio of 1/2/14~20/0.5~8.0. As the results, for the $SO_2-I_2-H_2O$ Bunsen reaction system, the ranges between the starting point and the saturation point for two liquid phases separation were determined by calculation. The best result for the minimization of impurities (HI and $I_2$ in $H_2SO_4$ phase and $H_2SO_4$ in $HI_x$ phase) in each phase was obtained in an optimum condition with the highest temperature of 353 K and the highest $I_2$ molar composition. In this condition, the $HI/H_2SO_4$ molar ratio in the $H_2SO_4$-rich phase and the $H_2SO_4/HI_x$ molar ratio in the $HI_x$-rich phase were 0.024 and 0.028, respectively. For the distribution of $H_2O$ to each phase, it is appeared that the affinity between $HI_x$ and $H_2O$ was more superior to that between $H_2SO_4$ and $H_2O$. The affinity between $HI_x$ and $H_2O$ was decreased with increasing temperature but increased with increasing $I_2$ molar composition.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.439-450
• /
• 2009

The purpose of this study is to find out characteristics of the fillers made by epoxy resin (L-30) and filling epoxy resin (L-50) with talc, quartz sand and wollastonite with different mixture ratio of 5%, 50%, 80%, 120%, and 150%. The viscometer and colorimeter were used to measure the viscosity and chromaticity of the fillers. Additionally, IC and SEM were used to reveal characteristics of the filler, and checked ultrasonic wave velocity, compressive strength and contact angle to estimate the stability between the filler and stones which are essential for conservation treatments. The filler mixed with the talc had the lowest value in the ultrasonic wave velocity analysis, and its compressive strength decreased as the mixing rate of talc increased. On the other hand, wollastonite had higher values than others in the ultrasonic wave velocity and the compressive strength regardless of epoxy resin type, also, these values increased as mixing rate increased. The properties of the filler, which include the granularity and shape, have influence on characteristics of the stone conservation adhesives. Thus, the filler type, characteristic, and mixture ratio must be considered for effective conservation treatment.

• Korean Journal of Remote Sensing
• /
• v.39 no.2
• /
• pp.129-142
• /
• 2023

This study analyzed the ratio of carbon monoxide (CO) and carbon dioxide (CO₂), CO and nitrogen dioxide (NO₂) for cities and regionsin Korea and China using column-averaged carbon dioxide dry-air mole fraction (XCO₂) of the Orbiting Carbon Observatory-2/3, CO and NO₂ vertical column density (named XCO, XNO₂ in thisstudy) of TROPOspheric monitoring instrument from April 2018 to April 2022, and presented the relationship between socioeconomic indicators (population, number of vehicles, Gross Regional Domestic Product) and ratio, and differences in characteristics between Korea and China. First, CO₂ and CO were analyzed after calculating ΔXCO₂ and ΔXCO removing the background value and trend line due to the difference in atmospheric residence time of three gaseous substances (CO₂, CO, and NO₂). Comparing the three values by regions, ΔXCO and ΔXCO₂ were relatively higher in China and XNO₂ were higher in Korea and the ratio of both values (ΔXCO/ΔXCO₂, ΔXCO/XNO₂) was higher in China than in Korea. ΔXCO/ΔXCO₂, ΔXCO/XNO₂ and socioeconomic indicators have a positive correlation suggesting that the concentration of air pollutants and greenhouse gases is higher as the city is large and the economic activity is active. Regarding the differences in the ratio characteristics of Korea and China, the relationship between ΔXCO and ΔXCO₂ showed a negative correlation in Korea and a positive correlation in China. When the relationship between ΔXCO and XNO₂ was examined for summer and winter, the change of ΔXCO by season was not significant in Korea, whereasthe change of ΔXCO and XNO₂ by season waslarge in China resulting in the relationship between two countries appeared differently. These results suggest that seasonal variability and national emission characteristics should be considered in the process of analyzing the ratio of greenhouse gases to air pollutants.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.38 no.11
• /
• pp.1559-1563
• /
• 2009

Scaled-up production of oil containing diacylglycerol (DAG), so called diacylglycerol-oil, was produced by lipase-catalyzed reaction. Mixture of soybean oil and glyceryl monooleate with 1:2 molar ratio was esterified with Lipozyme RMIM in a batch-type reactor at 55$^{\circ}C$ and 300 rpm during 6 hr. After short-path distillation for removal of monoacylglycerol and free fatty acid as reaction by-products, diacylglycerol-oil mainly consisted of DAG (29 area%) and TAG (71 area%). The major compositional fatty acids in diacylglycerol-oil were oleic (44.36 wt%), and linoleic acids (37.36 wt%). Acid value and iodine value of diacylglycerol-oil were 0.13 and 112.6, respectively. Solid fat content (SFC) of diacylglycerol-oil was observed after differential scanning calorimetry (DSC) analysis in which three melting peaks at -25.0, 0.1, and 11.2$^{\circ}C$ were shown.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.720-727
• /
• 2017

This study determined the optimum mix proportions for volcanic-ash-based geopolymer by analyzing the flow, setting time, and compressive strength. $Na2SiO_3$ and NaOH were used as alkali activators, and NaOH concentrations of 2, 4, 6, and 8M were used for different experimental cases. The A/B ratios examined were 0.25, 0.3, 0.35, 0.4, and 0.45, and the ratios of volcanic ash to blast furnace slag binder were 7:3, 6:4, and 5:5. In the experiment, the flow and setting time tended to decrease and the compressive strength increased as the molarity of NaOH in the geopolymer increased. The optimum molarity of NaOH was determined to be 4M. As the A/B ratio increased, the setting time decreased and the compressive strength increased. The most advantageous A/B ratio for the setting time and strength was 0.35. Increasing the ratio of volcanic ash resulted in a longer setting time and lower compressive strength. The optimum binder ratio was chosen as 6:4 based on the setting time and compressive strength. Thus, 4M of NaOH, an A/B ratio of 0.35, and binder ratio of 6:4 are considered as the proper parameters for the volcanic-ash-based geopolymer.