• Journal of the Korean Wood Science and Technology
• /
• v.8 no.2
• /
• pp.1-5
• /
• 1980

This study is carried out to determine the scavenging effect of resorcinol added into the urea formaldehyde resin on the formaldehyde release of plywood, as the preliminary study of using the phenolic substances. The method for formaldehyde determination used in this report is the improved chromotropic acid determination. The results are summarized as follows: 1. Resorcinol added into the urea formaldehyde adhesive acts as a good scavenger. 4 percent of resorcinol reduced the formaldehyde release to less than half content. 2. Adding resorcinol gave better glue shear strength than that of control, showing the peak of the shear strength, at 2 percent and decreased to the same strength as control along its content of 4 percent. 3. Moisture content of air dried plywood met the standard very well.

• Journal of the Korean Wood Science and Technology
• /
• v.8 no.2
• /
• pp.9-16
• /
• 1980

The problem of tauns having the characteristics of severe variations in quality and unequally distributed moisture content in veneer sheets after drying for plywood could be cured to a proper even moisture distribution by the peeling of veneers in a prolonged period. The poor gluability of tauns was improved by applicaton of increased resin content of glue in spreading. Combinations of tauns with lauan and kapur for plywood showed good shear strength.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.15-19
• /
• 1996

To utilize the waste materials and develope wood adhesive from isolated bloods of slaughtered cow and pig and also to prevent water pollution, simple and rapid method of isolation and purification of plasma proteins from pig bloods with trichloroacetic acid(TCA) treatment was developed. Adding of TCA-precipitated blood powder to the phenol formaldehyde resin(PF) improved dry and wet strength of plywood and resulted in fast hot pressing times.

• Composites Research
• /
• v.30 no.4
• /
• pp.235-240
• /
• 2017

Animal glue, a water-soluble adhesive, has been used historically for high-performance traditional furniture despite the disadvantage of weakness against moisture. Many scientists studied the ways to improve water resistance of animal glue. Improvements on the interfacial, thermal, and water resistance properties of wood sandwich composites (WSC) was studied with carbon nanotube (CNT) wt% in animal glue. Real-time temperature of WSC was measured after WSC was heated with increasing CNT wt%. Lap shear test was performed to determine the interfacial properties of wood and animal glue with CNTs. Water resistance properties of animal glue were determined by lap shear test using specimens dipped in water and the results were compared with the dry case. Hydrophobicity of animal glue by static contact angle was correlated with the variation of lap shear test. Interfacial, thermal, and water resistance properties for animal glue were improved with properly added CNTs.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.2
• /
• pp.107-121
• /
• 2021

The purpose of this study is to optimize the bonding method of the plywood suitable for cross-laminated timber (CLT) with plywood as a core by analyzing the flexural performance and failure mode according to the lamina species, the method of bonding plywood in the longitudinal direction, and whether or not adhesive is applied to the joint. In the case of the Douglas fir lamina layer, the modulus of elasticity decreased by about 11.5% due to longitudinal bonding, and the modulus of rupture increased or decreased according to the adhesive application and bonding method. The optimal conditions were derived as the butt joint without adhesive, half lap joint with adhesive, and butt joint. In the case of the larch lamina layer, the modulus of rupture and the modulus of elasticity decreased by about 15% and 40%, respectively. When using the half lab joint and tongue & groove joint, it is believed that it reduces the load transmitted to the middle layer by primarily preventing the failure on flexure at the joint of the plywood layer. From the results of this study, the larch lamina layer used in the manufacturing process of Ply-lam CLT did not show any difference based on the bonding method. Butt joint and half lap joint bonding method are determined to be suitable when using Douglas fir lamina layer.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.1 s.129
• /
• pp.87-96
• /
• 2005

This study was carried out to evaluate the shear bond strength and adhesive bond durability of structural glued laminated timber (glulam) manufactured with mixed species lumber of Korean red pine, Korean pine and Japanese larch, using resorcinol adhesive and water-based polymeric-isocyanate adhesive (WPI). Each board used as a glulam lamina was graded by visual inspection. The visual lumber grade of the all species was very low due to the large size and number of knots and the steep slope of grain. In view of the results, appropriate pruning, sawing and drying processes might be needed to produce high grade lamina lumber with small knot size and drying defect free. Shear bond strength of every tested glulam specimen ranged between 7.9 and $9.9N/mm^2$, and much higher than the Korean Standard (KS) for glulam shear bond strength, $7.1N/mm^2$. There was not much shear bond strength difference between wood/resorcinol and wood/WPI. The resorcinol adhesive bond durability exceeded KS requirements. However, delamination on the end-grain surfaces of WPI glulam submerged in both room temperature and boiling water severely occurred, and its durability did not meet KS requirements. Further investigations may be required, and special care should be taken, to ensure long service life of WPI glulam used for exterior application. Results of this study are expected to be useful for improvement of mechanical properties and structural performance of mixed species glulam.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.28-35
• /
• 2017

In this study, specimens of rigid frame joint were produced by integrating joints with adhesive and other specimens were produced by inserting a wooden gusset integrated with a column member into a slit-processed beam member and joining them with pins. Then the moment resistance performances of the specimens were examined. For the wooden gusset, a GFRP-reinforced wooden gusset was used. The calculation results of perfect elasto-plasticity for the frame specimens for which a GFRP-reinforced wooden gusset was inserted into and joined with the slit-processed beam member by pins were 20-80% lower compared to the control group which consisted of steel plate-inserted frame specimens. The rigid frame specimens for which the column and beam members have been integrated with adhesive showed almost no initial residual transformations, as well as 38% greater initial rigidity and 41% greater plasticity compared to the steel plate-inserted joint.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.315-322
• /
• 2016

Block-glued glulam is a structural material that can be used as a construction member of a large-section wooden building, which is produced by edgewise bonding of two or more glulam beam elements. The edgewise bonding performance of the block-glued glulam was examined through delamination test and block shear strength test. According to the test results, the block-glued glulam that was manufactured with 1.5 MPa of compressive pressure after applying $500g/m^2$ of Resorcinol adhesive showed the best edgewise bonding performance. The block-glued glulam produced in a good edgewise bonding condition was compared with a control glulam with the same section modulus for bending strength performance. The modulus of elasticity (MOE) in bending was similar to that of the control glulam. The modulus of rupture (MOR) of the block-glued glulam was higher by 27% than that of the control glulam. No interfacial failure or cohesive failure were observed in the edgewise bonding layer.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.1
• /
• pp.11-16
• /
• 2010

Unlike other composites boards such as fiberboard and particleboard, plywood is manufactured with sheets of veneers. When the plywood manufactured, the adhesive is spreaded through gluelines on each surface of veneers. For that reason, formaldehyde emission of plywood can be considered as different way. Therefore, this research was conducted to understand the formaldehyde emission pattern of plywood. To measure formaldehyde emission, four different specimen preparing methods were used. The test specimen taken by a total surface area, a given number and a total side area showed inconsistent results. On the other hand, the result of formaldehyde emission showed consistency when considered only the length of adhesive layers.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.2
• /
• pp.84-91
• /
• 2003

In this study, the three species (Populus euramericana, Pinus densiflora and Quercus variabilis) were cut to difference (0, 0.15, 0.3, 0.45 mm) between the size of tip and that of root of the finger (DSTR) and jointed with poly vinyl acetate (PVA) and resorcinol-phenol resin (RPR). We described the relationship between the bending strength properties of finger DSTR and the acoustic emission (AE) generated during the bending test. The results were as follows: The AE generation time of finger-jointed specimens with RPR adhesive was earlier than that with PVA adhesive. The AE cumulative event count of finger-jointed specimens with RPR adhesive continuously increased with increasing load and the event count was much more than that with PVA adhesive. Also, the AE cumulative event count for resorcinol-phenol resin adhesive obtained from low load level was abundant. The AE wave in finger-jointed specimens with RPR adhesive could be detected in the below proportional limit load. Therefore, AE signals from bending test are useful for the estimation of strength in finger DSTR specimens.